Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Distributes load under drum support fasteners to prevent hardware loosening. Replace if worn, cracked, or causing noise. Confirm fit with your model number.
Simple fix, right parts fast. Read more
4-wire power cord connects your electric dryer to a 4-prong household outlet. Replace a worn, damaged, or overheated cord to restore safe power connection.
I previously ordered the heating element, thermostat, and fuse. Also the rear drum rollers. However, after completing that repair I noticed that the terminal block and power cord had some damage from an apparent overheating while allowing the dryer to continue to run in order to dry the clothes. All is well now and the unit is working just fine. I appreciate the quick delivery of all 3 orders. Read more
Dryer not heating or overheating? This temperature switch monitors heat levels and cycles the heating element. Direct replacement restores proper drying.
Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.
We replaced the broken door hinge. Read more
Fix rattling or gaps at the top of your dryer with this front top panel lock. Secures the panel to the cabinet frame for a tight, aligned fit.
With the thermister Read more
Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.
I replaced the Temperature Selector Switch with a new one ordered from AplpliancePartsPros.com Read more
Dryer idler pulley maintains belt tension for smooth drum rotation. Replace if dryer squeaks or makes loud noises. Verify fit with your model number.
Replaced rollers, belt and idler pulley Read more
Replace a cracked or missing dryer mounting bracket to keep components securely aligned. Restores support to prevent movement and premature wear.
Disassembled dryer, replaced worn parts and reassembled dryer. Removed top cover, disconnected front connector, removed front panel, removed belt from idler pulley, removed washer drum and belt, replaced push clip, retaining clips, 2 support rollers and idler pulley. Reassembled in reverse order. Read more
Fixes excessive vibration and rattling from dryer motor movement. This clamp secures the motor to its bracket, restoring stability. DIY-friendly repair.
Replaced the motor, blower, rear drum felt seal, and drive belt. Vacuumed up the lint everywhere, cleaned extra lint out of the chute, around the blower, and rear vents. Read more
Timer won't advance and dryer runs continuously? This 4-cycle timer controls cycle selection and timing. DIY repair typically takes 15-20 minutes.
Part ordered installed (easy), fixed problem for two loads of wash. Dryer then ran but did not heat. Researched on web and tested thermal interrupt fuses. Ordered (easy install) and now all is well. In the course of the fix it became apparent that the exhaust vent had rotted open on the portion resting on the floor. This was blowing hot air into and below the dryer and opened the fuse. All fixed, all is well. appliancepartspros.com Rated as a ten!!!!! Read more
Plastic drum baffle that lifts and tumbles clothes during drying. Replace if cracked, broken, detached, or missing from inside your dryer drum.
I installed it my self by watching your video Read more
Connects your dryer to the wall outlet to supply household electricity. Replace a damaged, frayed, or overheated cord to restore safe power connection.
Thanks to you, all went well. No problems. Read more
Factory protective shield panel for dryer assembly. Guards internal components and directs heat or airflow. Replace if cracked, broken, or missing.
I changed the thermostat and replaced the worn out seals. Read more
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
It was very easy to fix after watching your video.. Read more
Hex head screw for trash compactor assembly. Replaces lost, stripped, or damaged screws during repairs. Essential hardware for securing components.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Factory retaining nut secures dryer components with mating bolts or studs. Replace worn, stripped, or missing nuts to restore tight fit and prevent rattling.
Replaced the drum support rollers and shaft, plus the idler pulley. Read more