Wtw4955hwo Parts

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This part is a genuine OEM replacement drive motor. It is intended to replace a broken or faulty motor in various washers.This motor drives the washing machine, allowing the drum to rotate and agitate when the user selects the desired settings. Over time, the motor might become worn or start to malfunction, requiring immediate replacement. Before starting the repair process, unplug the appliance from the power source and check the resistance running through the motor windings using a multimeter. If the meter measures infinite resistance, the drive motor will definitely need to be replaced. Work gloves should be worn to prevent injury.This part has been made by Whirlpool and has been sourced directly from the manufacturer. This part is made out of high-quality, durable, non-corrosive materials to ensure high quality and is sold individually. It is compatible with washing machines manufactured by Whirlpool, Maytag, Jenn-air, and various other brands.

The Washplate is an OEM part for Whirlpool washing machines. The washplate is responsible for improving agitation and making sure clothes receive adequate and even washing.

Causes of washplate failure tend to be normal wear and tear over time, housing debris or foreign objects that become lodged in the washplate mechanism, or damage due to impact from heavy or unbalanced loads.

Symptoms of a bad washplate include:

• Improper water filling or drainage
• Imbalanced loads
• Excessive noise and vibration
• Uneven or inadequate cleaning results 

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

This rotary encoder mounts behind the washer's cycle knob and tells the main control which setting you select. When it fails, selections may be erratic or unresponsive. Replacing it restores accurate, dependable cycle selection. What it does

• Detects the position of the cycle selector knob
• Sends selection signals to the main control board
• Enables precise cycle and option changes
• Common symptoms: knob turns but lights don't follow, random/incorrect selection, can't select a cycle, won't start

• One rotary encoder

• Disconnect power to the washer before servicing
• Access the control console and remove the knob/dial to reach the encoder
• Note orientation, unplug the harness, release tabs/screws, and swap in the new encoder
• Handle electronics carefully and avoid static discharge; verify knob-to-light tracking before reassembly

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The washer pulley Cover is an OEM replacement part for Whirlpool washing machines. It is a removable plastic shroud that houses the drive pulley and belt mechanism.

Causes of a bad pulley cover can include cracks or breaks from repeated opening and closing over time. Chemical or moisture exposure can also damage plastic through standard usage cycles. 

Symptoms of a failing pulley cover include:

• Inability to properly close or latch the cover  
• Leaks or debris entering the pulley compartment
• Interference with belt or pulley movement
• Loose fasteners or mounting points that cause misalignment

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory screw fastens panels and components in your appliance to keep assemblies secure and aligned. Replace a missing, stripped, or rusted screw to restore a tight, rattle-free fit and reliable performance in the specified locations.

• Secures brackets, covers, and internal parts per the original design
• Helps prevent loosening, vibration, and rattling from unsecured panels
• Restores proper fastening when the original screw is missing, damaged, or stripped
• Direct-fit hardware for the designated points in compatible models

• Disconnect power; for gas or water appliances, shut off supply before service
• Match the driver to the screw head; start threading by hand to avoid cross-threading
• Tighten snugly; do not overtighten, especially into plastic bosses or thin sheet metal
• Clear debris and confirm alignment before tightening

Includes connector and both clamps.