Wtw4955hwo Parts

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This replacement nut is a small hardware fastener used to secure components inside your appliance. It helps keep parts tight and properly aligned so assemblies don't loosen from vibration or normal operation.

• Threads onto a mating bolt, stud, or shaft to clamp parts together
• Maintains alignment and reduces movement and rattling
• Replaces a stripped, missing, or damaged nut to restore a secure fit
• Common signs of failure: loose panels or components, unusual vibration/noise, hardware missing

• Disconnect power; shut off gas and/or water if applicable before servicing
• Note the original hardware stack-up (washers/spacers) and orientation for reassembly
• Start by hand to avoid cross-threading; tighten to manufacturer guidance—do not overtighten
• Replace any damaged washers or locking devices

This dishwasher dispenser stores detergent and rinse aid and releases them at the correct points in the cycle to support consistent cleaning results. Replace a broken, stuck, or leaking dispenser to restore reliable detergent delivery.

• Holds detergent and rinse aid and dispenses them automatically during the wash and rinse portions of the cycle
• Door/actuator mechanism controls the timed release of detergent
• Seals help prevent leaks around the dispenser opening
• Typical failure symptoms: detergent cup won't latch or open, detergent left in the cup, rinse aid not dispensing, or leaks from the dispenser area

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire connector
• Release mounting screws/clips, clean the door cutout, and seat the new dispenser evenly
• Tighten screws in a cross pattern to compress the gasket uniformly; run a test cycle to check for leaks and proper operation

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Used from harness to top.

Right hand side. For screws use WPW10119828.

The Knob is an OEM component for Whirlpool dryers. As the user interface, it allows selections of temperature, settings, and time options with the twist of a finger.

Designed for comfort during extended cycles, the durable knob utilizes non-slip textured surfaces around robust internal gears. Integrated fasteners mount securely to shafts coupling knobs to their respective switches. 

Causes of faulty knobs can include stripped internal teeth from mineral deposits binding moving parts or broken mounting tabs weakened through normal wear over many years.

Symptoms of a damaged knob include:

• Failure to engage settings or spin freely  
• Dials loose on shaft allowing accidental shifts   
• Missing labels from normal cleaning/wear reducing visibility
• Cracks or breaks compromising seal against moisture

Replace yours today with this genuine Whirlpool knob to restore easy navigation of cycles. Compatible with Kenmore and some Maytag dryers.

Right hand side

This outer tub is the main water-holding housing for a top-load washing machine. It supports the inner basket and seals the wash chamber, helping the washer contain water and direct proper wash action. What it does:

• Holds wash water and surrounds the inner basket during fill, wash, and rinse cycles
• Supports the inner tub and transmission/agitator assembly for stable operation
• Prevents leaks by maintaining the sealed wash chamber; a cracked tub can cause visible water under the machine
• Helps reduce noise and vibration by keeping the wash components aligned

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain any remaining water from the tub and remove the washer cabinet or top to access the tub
• Transfer any components (basket, agitator, seals, mounting hardware) only if explicitly listed in your parts list; replace worn seals and gaskets when reinstalling

Restore precise cycle selection with this rotary encoder cycle switch. Mounted behind the control knob, it sends your chosen setting to the washer's control, resolving unresponsive or erratic knob behavior so the correct cycle and indicators engage.

• Translates knob rotation into signals the main control uses to select a wash cycle
• Helps ensure the selected cycle registers accurately on the user interface
• Wear or internal faults may cause an unresponsive or erratic cycle knob
• May also lead to incorrect indicator lights, intermittent selection, or a no-start condition

• Disconnect power before servicing
• Pull the knob straight off; open the console to access the encoder
• Release locking tabs and transfer wiring one connector at a time; align the keyed shaft
• Reassemble and verify the indicators respond to knob rotation before running a load

This fill hose carries water from the home supply to the appliance inlet valve, restoring proper water fill and helping prevent leaks when the original hose is cracked, worn, or blocked. Ideal for replacing damaged inlet lines. What it does:

• Delivers water from the household supply to the appliance inlet valve for normal fill cycles.
• Replaces cracked, split, or deteriorated hoses that can cause leaks at connections.
• Resolves symptoms such as slow or no water fill, visible leaks, or intermittent filling.
• Durable replacement designed to match OEM routing and connection points.

• Always shut off water supply and disconnect power before starting work.
• Inspect and replace hose clamps or inlet gaskets as needed; ensure proper seating to prevent leaks.
• Hand-tighten fittings and secure clamps—avoid overtightening metal fittings.
• After installation, restore water and power and run a short fill cycle while checking for leaks.

This electronic control board is the appliance's main logic module, coordinating sensors, user inputs, and component power to run cycles correctly. Replacing a failed board can restore normal operation when controls are unresponsive, cycles won't start, or error codes persist. What it does:

• Manages timing and sequencing for selected cycles and options
• Interprets control panel input and switches power to motors, valves, fans, or heaters
• Monitors sensors and switches; can trigger safety shutoffs when faults are detected
• Common symptoms may include: won't start, unresponsive controls or display, stops mid-cycle, erratic beeping/lights, or error codes

• 1 electronic control board

• Disconnect power at the breaker or unplug the appliance before servicing; if gas is involved, shut off the gas supply
• Use ESD precautions; handle the board by the edges and avoid touching components
• Photograph/label connectors; move wiring one at a time and transfer any jumpers or mounting hardware from the original board if present
• Restore power and run model-specific diagnostics; some models require calibration or configuration after control replacement—refer to the service information for your unit

Size: .20 Fl. Oz. (6 ml)

Screw: 8-16 x 3/8 inch.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening