Wtw57avs-W1 Parts

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This vacuum break hose connects the water path to the appliance's anti-siphon assembly to help prevent backflow. Replace a cracked, brittle, or leaking hose to restore safe water flow and stop nuisance leaks.

• Routes water between components of the vacuum break/anti-siphon assembly
• Helps maintain proper backflow protection in the water path
• Common symptoms: water dripping or pooling near the rear/top, leaking during fill, visible cracks, swelling, or loose hose ends
• Restores reliable, leak-free connections when the original hose deteriorates

• Disconnect power and turn off the water supply before servicing
• Place a towel/container to catch residual water when removing the old hose
• Use pliers or a driver to release hose clamps, then transfer and secure the new hose with existing clamps
• Route the hose exactly like the original and check for kinks; restore water/power and verify no leaks

This lid hinge pad fits between the washer lid hinge and the cabinet. It cushions the joint to reduce squeaks and metal wear, helping keep the lid aligned and operating smoothly.

• Provides a protective wear surface between the hinge and cabinet/lid
• Reduces squeaks, creaks, and rattling when opening or closing the lid
• Helps maintain proper lid alignment and smooth movement
• Common signs it's worn or missing: squeaking lid, rubbing/scuff marks at the hinge, loose or wobbly lid

• Disconnect power to the washer before servicing
• Support the lid to relieve hinge tension and access the hinge area per your model
• Remove the worn pad and press the new pad fully into the hinge location
• Test lid operation; inspect the opposite hinge and replace its pad as needed if your model uses two

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

Replacement lid strike assembly that secures the washer lid so the machine can operate reliably. Restores proper lid engagement to help prevent the washer from stopping mid-cycle or the lid from coming unsecured during use. What it does:

• Engages with the lid latch to hold the lid closed during wash and spin cycles
• Restores proper lid alignment and secure closure when the original strike is worn, broken, or missing
• Common repair for symptoms like the lid not staying latched, the washer refusing to start, or a rattling/slipping lid

• Disconnect power before servicing the washer
• Typically installs at the lid/hinge area; may require removing the top panel or console for access
• Use basic hand tools and take care around springs and hinges to avoid injury

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

This timer skirt assembly replaces a cracked, worn or loose dial skirt so the timer knob fits securely and operates smoothly. It restores proper knob alignment and protects the timer control opening. What it does:

• Replaces a broken or cracked dial skirt that lets the knob wobble or sit unevenly
• Helps the timer knob engage the control shaft correctly for reliable selection
• Covers and protects the timer mechanism from dirt and debris around the control
• Reduces knob play and improves the appearance of the control panel

• Disconnect power to the appliance before servicing to avoid shock or injury
• Typically requires removing the control knob and/or control panel; have basic hand tools ready
• Handle plastic parts gently to avoid cracking; align skirt before securing components

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Part of the agitator cam (short) assembly. For complete repair kit use 285809.

This adjustable leveling leg helps stabilize and properly level your appliance on uneven floors. Replacing a worn or missing leg reduces wobble and vibration so doors align and the unit operates smoothly.

• Screws into the base to raise or lower a corner for precise leveling
• Helps prevent rocking, vibration, and rattling during use
• Promotes even weight distribution to protect the cabinet and flooring
• Restores proper door/drawer alignment once the unit is level

• Disconnect power; shut off water supply before servicing
• Carefully pull or tip the appliance to access the leg; use a helper for safety
• Start threads by hand, then adjust height with a wrench—do not over-extend
• Verify level front-to-back and side-to-side; recheck after moving or loading

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A