Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This refrigerator lamp socket holds an E12-base appliance bulb and provides the electrical connection for the light fixture. Replace it when the light won't turn on or flickers despite a known-good bulb and functioning door switch.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:
Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more
Refrigerator primary ice and water dual coil water inlet valve. For the filter valve order WR57X10024. For the assembly including both the primary and filter valve having the short bracket order WR57X10026. For the assembly including both the primary and filter valve having the long bracket order WR57X10022.
First, I had to remove the cover plate on the back of the refrigerator. Then I unscrewed the water inlet valve from the rest of the assembly. I then unplugged the electrical contacts by pulling them apart. There are two fittings on the valve. One has a nut on it. That one just needs the nut unscrewed, after which the pex tubing can be pulled out. The other one has a pex connection. This one can be separated by simultaneously pushing in on the fitting neck while pulling the pex tubing out. On... Read more
This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.
I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more
Door solenoid with plunger.
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside.... Read more
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more
This icing kit is a factory update designed to reduce frost build-up in the ice/dispenser area. It improves sealing and insulation to help keep the ice path clear and restore reliable dispensing performance.
Firstly, the Ice Door had a kink in the edge, which caused it to stay open and create lots of frost on the coils. $5.00 part, highly recommend it. (By the way, the new door was little too big and it too stay propped open and left a gap so I had to trim the top edge of the rubber with scissors to get it to fully close.) Secondly, there are two heaters for the defrost cycle, one that goes around the coils and another attached to a collector pan beneath the coils. When the cycle hits, those... Read more
This straight 1/4-inch water line coupler joins two sections of 1/4-inch OD refrigerator tubing, restoring a secure connection in dispenser and icemaker supply lines. Use it to splice, repair, or extend existing tubing.
Replaced hoses. They were not an exact replacement but they did end up working with the purchase of one additional fitting (5/16 x 1/4 coupler) Read more
This LED transformer supplies low-voltage power for your refrigerator's interior lighting. Replacing the transformer can restore consistent illumination when the doors open.
Tested the input voltage of the transformer (located at the bottom of the fridge) at 125V. Tested the output voltage and was only getting 1 volt. Ordered the listed new transformer, installed it, which was a major pain in the A*&^^& just not a lot of room to work with, but did get in in and "voila" the LED panel worked again! Very quick shipping from Appliance Parts Pros which included the correct part, Thank you. Read more
This water inlet valve controls the flow of household water into the refrigerator's ice maker during fill cycles. Replacing a sticking or leaking valve restores proper ice fills and helps prevent nuisance leaks at the back of the unit. What it does:
I researched the problem online and determined it was undoubtedly the water valve leaking. A visit to AppliancePartsPros.com to order the replacement valve and I was ready to go. Actual repair only took 15 minutes. Read more
This refrigerator dispenser funnel extension attaches at the front of the dispenser to better direct the stream into your cup. Replacing a cracked or missing extension reduces splashing and helps keep the dispenser area cleaner.
I ordered the ice door assembly and a door recess spring and while I was working on that particular area the ice chute funnel that kept falling off on one side. It was all very easy, took maybe 15 mins in all. I watched the "how to" video that was posted and it was extremely helpful, giving me to confidence to do this myself. The only thing I might do different another time would be to take a look at the assembly before ordering parts. I didn't as I didn't want to keep opening the area up... Read more
The Damper Assembly is an OEM component specifically designed for GE refrigerators. This assembly is located within the fresh food compartment and functions to control airflow and temperature regulation.
The damper works with the evaporator fan to carefully moderate circulating air, preventing cold spots and optimizing equal cooling. Consistent temperatures extend the shelf life of perishable goods.
Causes of a faulty damper assembly can include failure of the plastic gears or axle that coordinate its movements over time. Improper air circulation disrupts the refrigerator's performance.
Symptoms include:
This replacement assembly from GE restores dependable temperature control. Upgrade today for continued fresh food preservation abilities matching OEM standards. It is also compatible with Hotpoint, RCA, and some Kenmore models.
I replaced all sensors and defrost thermostat's, defrost heater, fan motor Read more
This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:
Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more
This Top LED board is the interior illumination module that provides the fridge's top-area lighting, restoring clear, even light for food visibility and convenience. What it does: