Thermal Coupler Parts

This line fuse protects the appliance's incoming power circuit by opening if an overload or short occurs. Replacing a blown fuse can help restore power once the underlying issue is corrected, preventing further damage to sensitive components.

• Interrupts line voltage when excessive current or a short circuit is detected
• Typical symptoms: unit completely dead, no display or interior lights, won't start or run
• Fuse tests open/no continuity with a multimeter when blown
• A blown fuse often points to another fault that must be addressed

• Disconnect power at the breaker/unplug before servicing; microwaves contain high-voltage parts that can retain a dangerous charge even when unplugged
• Replace only with the same type and rating as the original fuse
• Ensure the fuse seats firmly in its holders; do not bypass or jumper a fuse

2 clamps included.

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

The Faucet Adapter is an OEM part for GE dishwashers. This adapter connects the dishwasher’s water supply hose to a standard kitchen faucet, allowing the dishwasher to draw water for the wash cycles.  

Causes of a bad faucet adapter can include regular wear and tear, damage from frequent attachment and detachment, or cracks and leaks from improper handling.  

Symptoms of a bad faucet adapter include:

• Water leaking from the connection point
• Difficulty attaching the adapter to the faucet
• Reduced water flow to the dishwasher
• The dishwasher not filling with water properly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This outlet thermistor monitors exhaust air temperature in the dryer's outlet duct and reports it to the control. Replacing a faulty sensor helps restore accurate heat regulation, preventing over- or under-drying for consistent drying performance. What it does:

• Measures outlet/exhaust air temperature and sends a resistance signal to the control board
• Helps the control cycle the heater or burner on/off to maintain proper drying temps
• Failure symptoms can include long dry times, no heat, overheating/shutting off, or inconsistent temperatures
• May illuminate a sensor-related error on models with diagnostics

• 1 outlet thermistor

• Disconnect power; shut off gas supply for gas models before servicing
• Access the exhaust/outlet duct or blower housing (location varies by model); the thermistor mounts on this duct
• Note wire locations, remove the fastener/clip, transfer any bracket if present, and install the new sensor with its tip in the airflow; secure connections
• Reassemble and run a test cycle to proper heat cycling

This dryer safety thermostat monitors internal temperature and opens the circuit if the unit overheats, protecting the heater and wiring. Replacing a failed thermostat restores proper over-temperature cutoff and safe, consistent drying performance. What it does:

• Monitors air temperature at the heater/exhaust path
• Interrupts power to the heating element if temperatures exceed its limit
• Helps prevent overheating and thermal damage
• Common symptoms can include: no heat, heat cutting out early or overheating, or the dryer shutting off on high heat

• 1 safety thermostat

• Disconnect power before service; for gas dryers, also shut off the gas supply
• Typically mounted on the heater housing or exhaust duct; note wire positions and transfer one at a time
• Secure with existing hardware and ensure tight electrical connections
• After replacement, clean the lint filter, vent hose, and exhaust duct to ensure proper airflow and prevent repeat overheat trips

This temperature-control thermistor (temperature sensor) feeds accurate temperature data to the control so your appliance can cycle components correctly and, where applicable, manage defrost. Replacing a faulty sensor restores stable operation and consistent performance. What it does:

• Senses temperature and varies resistance to report conditions to the control
• Helps the control regulate system cycling for proper operation
• Supports defrost logic where applicable to prevent coil icing
• Common failure signs: erratic temperature control, short/long cycling, icing on the evaporator, or unexpected shutoffs

• 1 thermistor

• Disconnect power before servicing
• Note the original sensor location and wire routing; install the new sensor in the same position
• Transfer any mounting clip or sleeve from the old sensor if needed
• Fully seat connectors and route wiring away from sharp, hot, or moving parts

This rack holder supports the removable rack inside the appliance cavity, keeping it level and secure during use. Replace a cracked or missing holder to restore proper rack positioning and safer, more reliable operation.

• Provides a fixed support point for the rack inside the cavity
• Keeps the rack level and prevents tipping or slipping
• Helps the rack slide in and out correctly when supports are intact
• Common signs to replace: rack won't stay in place, tilts or falls, visible damage or missing holder

• Disconnect power and allow the appliance to cool completely before servicing
• Remove the rack to access the holder
• Remove the fastener(s), note orientation, and swap in the new holder
• Reinstall the rack and confirm it sits securely before use

This thermal cut-off (TML) is a temperature safety device that opens the circuit if overheating is detected, protecting components from heat damage. Replace a failed or tripped cut-off to restore safe, reliable operation.

• Monitors temperature at its mounting point and interrupts power at a preset limit
• Helps prevent overheating damage to components and wiring
• Typical symptoms include no power, shutting off during use, or no heat—depending on where it's installed
• Can be tested with a multimeter; an open (no continuity) reading indicates replacement is needed

• Disconnect power before servicing; some appliances (e.g., microwaves) can store dangerous high voltage—use proper discharge procedures
• Replace with the same type/rating and mount in the same location/orientation as the original
• Ensure solid contact with the sensing surface and clear airflow/venting to prevent repeat overheating
• Do not bypass thermal safety devices; verify proper operation after installation

Color: brown. It measures about 8-1/2 inches in diameter.

This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:

• Cuts power when overheating is detected to protect internal components
• Helps prevent damage from shorted heaters, motors, or wiring faults
• Common symptoms: no power, won't start, shuts off during operation, no lights/display
• A blown fuse reads open (no continuity) and must be replaced—it is not resettable

• 1 thermal fuse

• Disconnect power before servicing to avoid electrical shock
• Access the fuse location per your model's service information; note wire orientation and mounting
• Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.

This high-limit thermostat is a temperature safety switch for the heating circuit. It opens the circuit if temperatures climb too high, helping protect the appliance and restore safe, reliable heating performance.

• Monitors temperature and interrupts power to the heater when a limit is exceeded
• Helps prevent overheating that can damage components or trip other safeties
• If failed open: heater won't energize; cycles may run long or never reach target temperature
• If stuck closed: unit may overheat or shut down as other safety devices trip

• Disconnect power at the breaker before servicing; allow the appliance to cool completely
• Access the thermostat at the heater/temperature control area as designed for your model
• Note wire positions and transfer one at a time; ensure tight, secure connections
• After replacement, inspect the heater and controls for issues that could cause overheating

This thermal switch is a temperature-sensitive safety device used in many ranges and wall ovens. It opens or closes an electrical circuit at a set temperature to protect internal components and help maintain safe operation. What it does:

• Monitors temperature and opens/closes a circuit at a specified threshold
• Protects the appliance from overheat conditions
• Cuts power to heating circuits or controls a cooling/vent fan, depending on model
• Common symptoms of failure include: oven or certain functions won't run, unit shuts off mid-cycle, or operation returns only after cooling

• 1 thermal switch

• Disconnect power at the breaker before servicing
• Access location varies by model
• Move wires over one at a time to the new switch and secure it firmly to its mounting surface
• After replacement, verify proper airflow and cooling to prevent repeat overheating

The Faucet Adaptor is an OEM part for GE dishwashers. This adaptor is designed to connect portable dishwashers to standard kitchen faucets, enabling the dishwasher to draw water and drain correctly during operation. It ensures a secure and leak-free connection between the faucet and the dishwasher hose.

Over time, the faucet adaptor can wear out or become damaged due to frequent use, exposure to water, and the constant attachment and detachment process. Causes of a bad faucet adaptor can include cracks or breaks in the adaptor, worn-out seals, or mineral buildup that affects its functionality.

Symptoms of a bad faucet adaptor include:

• Leaks or drips at the connection point
• Difficulty attaching or detaching the adaptor
• Poor water flow into the dishwasher
• Loose or unstable connection

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Microwave Coupler is essential for maintaining the proper functioning of your microwave. This genuine OEM part ensures a secure connection within your Samsung microwave, enhancing performance and reliability. Designed specifically for Samsung microwave models, it offers a perfect fit and seamless integration. The Microwave Coupler helps resolve issues such as interrupted power flow or inconsistent heating, ensuring your appliance works efficiently. By choosing this genuine OEM part, you benefit from superior quality and durability, which prolongs the life of your microwave. Easy to install, this coupler provides a straightforward solution to restore your microwave's functionality without hassle. Trust in the Microwave Coupler to deliver reliable performance and enhance your cooking experience with peace of mind.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings