Solenoid Parts

This replacement pump moves water/condensate through your appliance so it can drain or recirculate as designed. Replacing a weak or failed pump restores proper water removal and helps prevent leaks, overflows, or nuisance shutoffs.

• Moves collected water from the sump/collection area to a drain hose or internal passage
• Maintains correct water level to prevent overflow conditions
• Common failure signs: water won't pump out, leaks near the base, or loud buzzing/grinding from the pump
• May trigger "bucket full," drain, or pump-related error indicators, depending on the model

• Disconnect power before servicing; allow unit to cool, and expect residual water in the lines or pan
• Note hose routing and wiring connections; transfer any clamps, grommets, or fittings from the old pump if reused
• Ensure hoses are fully seated and not kinked; tighten connections and check for leaks after reassembly
• Test operation after installation and water is expelled properly

The Washing Machine Water Inlet Valve is an OEM part for Whirlpool brand washing machines. It regulates water flow into the washer tub during fill cycles and shuts off the supply automatically when the proper water level is reached.

Causes of a bad inlet valve include mineral buildup inside the valve filter restricting flow over time, or mechanical failures of internal plastic parts like diaphragms and seals due to usage stress.

Symptoms of a bad water inlet valve include:

• Slow or inconsistent filling during wash cycles  
• Water failing to shut off fully after the designated fill level  
• An inability to properly meter incoming water supply amounts
• Water leaks noticed beneath or around the valve area

This OEM replacement valve ensures precise water flow regulation. Compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.

This microswitch senses the microwave door position and controls the safety interlock circuits. Replacing a worn switch restores proper start/stop behavior so the oven only runs when the door is fully closed.

• Detects door open/closed status to enable or disable cooking
• Part of the safety interlock system that stops operation if the door opens mid-cycle
• Replace if the switch fails a continuity check or shows heat or terminal damage

• Disconnect power before service; microwave capacitors can retain a dangerous charge
• Note wire positions and move them to the same terminals on the new switch
• Ensure the door latch cleanly actuates the switch; test operation before reassembly

Liquid propane to natural gas

This overfill float and shaft assembly monitors the dishwasher's water level. As the tub fills, the float rises and triggers the float switch to shut off the inlet water, helping prevent overfilling and leaks.

• Senses tub water level and moves up/down with the water
• Activates the float switch to stop filling at the correct level
• Helps protect against overfill-related leaks
• Common symptoms include: won't fill (float stuck up), continuous filling/overfilling (float stuck down or damaged), or float not moving freely

• Disconnect power and turn off the water supply before servicing
• Lift the old float straight up from inside the tub; access the underside (behind the toe panel) as needed to release the shaft from the float switch lever
• Install the new shaft through the guide and onto the switch lever; seat the float so it moves freely
• Verify smooth float movement and test a fill cycle while checking for leaks

This water inlet valve controls the flow of household water into the dishwasher at the start of a cycle. Replacing a weak, stuck, or leaking valve restores proper filling performance and helps prevent fill-related errors and leaks. What it does:

• Opens and closes electrically to regulate water entering the dishwasher
• Helps ensure correct fill level and timing for each cycle
• Common failure symptoms: won't fill or slow fill, water seeping into tub when off, external leak at valve connections, loud buzzing/chattering during fill
• May set fill or water supply-related error codes on some models

• 1 water inlet valve assembly

• Disconnect power and turn off the water supply before servicing
• Have a towel or shallow pan ready for residual water when removing lines
• Transfer any original mounting hardware or fittings from the old valve as needed
• Inspect/clean the inlet screen and flush the supply line; check all connections for leaks after installation

This water inlet valve regulates the flow of household water into the refrigerator for ice making and dispensing. Replacing a failing valve restores proper fill and helps resolve leaks, low flow, and no-ice/no-dispense issues. What it does:

• Opens and closes to supply water to the ice maker and/or dispenser when energized by the control
• Addresses symptoms like no water at the dispenser, no ice production, slow fill/hollow cubes, or dripping/leaks at the valve area
• Common failures include stuck or leaking valve, clogged screen, or a failed solenoid coil
• Helps eliminate valve buzzing with no fill when the coil is energized but the valve won't open

• 1 water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Keep towels/containers handy; some residual water will drain when lines are removed
• Note and label each tube and wire position; transfer any fittings/brackets from the old valve if applicable
• After installation, restore water and power, check all connections for leaks, and purge air by dispensing water

The Hook is an OEM part for Bosch microwave doors. Manufactured from heat resistant composite materials, it firmly holds the door closed during cooking cycles.  

Causes of a faulty latch/hook include failures of being worn down from repetitive opening/closing motions over time. Exposure to high heat or abrasive cleaners also leads to decreased functionality.

Symptoms of a damaged latch/hook involve:

• Doors not sealing fully or locking properly
• Failure to open after cooking
• Degrading latch fittings allowing moisture or debris entry

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This triple-solenoid washer water inlet valve regulates and routes hot and cold water into the tub and dispenser as the control commands. Replacing a weak, stuck, or leaking valve restores proper fill, temperature mix, and cycle performance. What it does:

• Opens and closes to allow water into the washer based on cycle and temperature selections
• Three solenoids manage hot/cold mix and direct water to the tub and dispenser compartments
• Typical symptoms: won't fill, slow fill, fills when powered off, incorrect temperature, or leaks from the valve
• May trigger fill-related error codes or cause extended/paused cycles due to fill timeout

• One water inlet valve assembly with three solenoids

• Disconnect power and turn off both hot and cold water supplies before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Label and transfer each wire connector and hose to the matching port on the new valve
• After installation, open supply valves and run a test fill; inspect all connections for leaks

The Refrigerator Water Inlet Valve is an essential component for maintaining the optimal functionality of your Samsung refrigerator. This genuine OEM part ensures a reliable water flow to your ice maker and water dispenser, preventing leaks and interruptions in performance. Designed specifically for Samsung refrigerators, it guarantees a perfect fit and seamless integration with your appliance system. The durable construction of the water inlet valve offers long-lasting performance, reducing the need for frequent replacements and providing peace of mind. Installing this valve is straightforward, allowing you to restore your refrigerator's water supply quickly and efficiently. By choosing the Refrigerator Water Inlet Valve , you ensure that your refrigerator continues to deliver fresh, clean water and ice with consistent quality. Whether you're experiencing decreased water flow or suspect a malfunctioning valve, this genuine OEM part is the ideal solution to keep your Samsung refrigerator running smoothly and efficiently, enhancing your overall user experience.

The Refrigerator Ice Dispenser Valve Coil Solenoid is essential for the optimal operation of your Samsung refrigerator's ice dispenser. This genuine OEM part ensures reliable performance by controlling the flow of water to produce ice efficiently. Designed specifically for Samsung refrigerator models, it guarantees a perfect fit and seamless integration with your appliance. The valve coil solenoid plays a critical role in regulating ice production, preventing leaks, and maintaining a consistent ice supply. By replacing a faulty or worn-out solenoid with this high-quality component, you can restore your ice dispenser's functionality swiftly and effectively. Installation is straightforward, allowing you to perform the repair with ease and confidence. Choosing this genuine OEM part means you are investing in durability and dependable performance, ensuring your refrigerator continues to provide fresh ice whenever you need it. Enhance your fridge's performance and enjoy the convenience of a fully functioning ice dispenser with the Refrigerator Ice Dispenser Valve Coil Solenoid .

Includes water inlet valve, vacuum break, wire harness and connector hose.

This oven door latch assembly secures the door during the self-clean cycle and reports lock status to the control. Replace a worn or failed latch to restore safe locking and reliable self-clean operation.

• Locks the oven door during self-clean to prevent opening at high temperatures
• Signals the control when the door is locked or unlocked
• Helps the oven start and complete a self-clean cycle safely
• Typical symptoms: self-clean won't start or finish, door won't lock/unlock, lock motor runs continuously or is noisy, lock indicator stays on

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Access is typically from the top or behind the control panel; remove panels as required and note linkage/switch orientation
• Transfer any linkages or mounting hardware from the original latch in the same orientation
• Manually cycle the latch to verify smooth operation before restoring power and testing self-clean

Color: metallic. Measures about 1 inch high by 2 inches deep.

The Refrigerator Water Inlet Valve Assembly is essential for managing the water flow in your Samsung refrigerator. This genuine OEM part ensures precise control of water entering the appliance, which is crucial for ice makers and water dispensers to function correctly. Designed specifically for Samsung refrigerators, it guarantees a secure fit and reliable performance. The assembly helps prevent leaks and maintains consistent water pressure, enhancing the efficiency of your fridge. Installing this genuine OEM part means you are choosing a durable and long-lasting solution that restores your refrigeratorGÇÖs functionality effectively. Whether you are replacing a worn-out valve or addressing water flow issues, the Refrigerator Water Inlet Valve Assembly offers the quality and dependability you need. Trust in this genuine OEM part to keep your Samsung refrigerator running smoothly and ensure a better overall customer experience.

This gas valve regulates and safely delivers fuel to your dryer's burner. When operating correctly, it opens for ignition and closes when heat is satisfied, providing consistent, reliable heating for effective drying.

• Opens to allow gas into the burner when the ignition system calls for heat
• Closes to stop gas flow during cycling or if ignition fails
• Possible symptoms: dryer runs but no heat; igniter glows yet no flame; intermittent heat or long dry times
• Helps restore proper burner ignition and stable flame

• Disconnect power and shut off the gas supply before servicing
• Work in a well-ventilated area; check all connections for leaks with a non-corrosive leak-detection solution after installation
• Transfer any brackets, fittings, or orifices from the original valve as required; secure connections
• Confirm gas type (natural/LP) and regulator/orifice settings per the service manual before restoring service