Finite Switch Parts

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

This dual surface element infinite switch controls power to an electric cooktop or range's dual radiant burner. It restores precise heat selection and lets you choose inner-only or full dual-ring operation when the original switch fails.

• Regulates power cycling to maintain the selected heat level on a dual radiant element
• Selects between inner-only and dual-ring operation on compatible burners
• Common failure symptoms: no heat, only runs on high, cannot adjust temperature, burner won't shut off, dual feature won't engage
• Restores consistent, controllable surface cooking performance

• Disconnect power at the breaker before servicing—this is a high-voltage component
• Pull the control knob and open the control panel or rear cover to access the switch
• Photograph/note wire locations; move wires to the new switch one at a time
• Secure the switch, reassemble, restore power, and test both inner and dual-ring settings

This replacement switch assembly restores proper signaling between the dishwasher's mechanism and the control, so selected functions register and cycles can start and run consistently. A worn or failed switch can cause intermittent or no operation. What it does:

• Provides the on/off signal the control needs when the mechanism is actuated
• Can lead to a dishwasher that won't start or stops mid-cycle when failing
• May cause options or selections to be unresponsive or require extra pressure
• Heat damage or a broken actuator on the switch assembly can indicate failure

• 1 switch assembly

• Disconnect power to the dishwasher before servicing
• Access location varies by model; refer to your model's parts diagram/service information
• Photograph wiring and move connectors one at a time to the new assembly
• Verify secure connections and proper wire routing to prevent pinching during reassembly

This start switch completes the dryer's start circuit when you press Start, energizing the motor to begin the cycle. Replacing a worn switch restores consistent, reliable starting when the original becomes intermittent or electrically open. What it does:

• Completes the start circuit to send power to the drive motor when Start is activated
• Common failure symptoms include the dryer not starting or no response when pressing Start
• May cause intermittent starts that require multiple presses or jiggling
• Switch may feel loose or show heat discoloration at the terminals

• Includes 1 start switch

• Disconnect power to the dryer before servicing
• Access the control panel/console to reach the switch
• Label or photograph wire positions; transfer wires one at a time to the new switch
• Secure the switch, reassemble panels, restore power, and test start operation

The infinite switch regulates power to your range or cooktop's surface element, letting you set heat from low to high. Replace a failed switch to restore dependable burner control and consistent cooking performance.

• Regulates on/off power cycling to the surface element based on the knob setting
• Helps resolve no-heat, stuck-on-high, won't-turn-off, or erratic/uneven heat issues
• Often controls the surface "on" indicator light circuit; failure may affect the light
• Installs behind the control knob and connects to the existing wire harness

• Disconnect power at the breaker; allow the appliance to cool completely
• Remove the knob and access panel to reach the switch
• Photograph wiring and transfer wires to the same labeled terminals (commonly L1, L2, H1, H2, P)
• Reassemble, restore power, and test multiple heat settings; check the element and wiring

This push-to-start switch momentarily closes the start circuit to begin a cycle. Replacing a worn switch restores reliable starting when you press the Start button.

• Initiates operation by closing the start circuit when pressed
• Works with the door switch and timer/control to begin a cycle
• Common symptoms: won't start when Start is pressed; runs only while the button is held; intermittent starting; Start button feels loose or sticky
• Also known as an on/off PTS or start button switch

• Disconnect power before servicing
• Access the console/control panel and remove the start knob or button if present
• Move wires to the new switch one at a time to maintain correct terminal positions
• Secure the switch in the panel, reassemble, and test Start function

This surface burner infinite switch is the behind-the-knob control for an electric cooktop or range. It regulates power to a single surface element so you can dial in and maintain the heat you need.

• Regulates on/off power cycling to a coil or radiant surface element for variable heat control
• Helps address issues such as a burner not heating, only heating on high, not turning off, or fluctuating temperature
• Installs behind the control panel; connects with spade terminals to line, load, and element leads
• Single-surface-element control for one burner position

• Disconnect power before servicing; this component carries high voltage
• Note wire positions or transfer one wire at a time from the old switch to the new switch
• Secure the switch to the control panel and align the shaft with the control knob
• Reassemble and verify smooth low-to-high burner operation

This electrical microswitch opens or closes a circuit when its actuator is engaged, allowing the control to sense position or enable a function. Replacing a worn switch restores reliable signaling and prevents intermittent faults in select ranges and wall ovens. What it does

• Changes state (open/closed) when actuated to complete or break a circuit
• Sends feedback to the control or enables power to a related component
• Helps ensure operations start/stop only when the mechanism is in the correct position
• Failure signs can include intermittent operation, cycles that won't start or finish, or related error codes/alarms

• 1 switch

• Disconnect power at the breaker before servicing
• Note/photograph wire positions and transfer one at a time to the new switch
• Match actuator orientation to the original and secure the switch firmly
• Verify function with a multimeter (continuity changes when actuated) before reassembly and testing

This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.

The Refrigerator Door Switch is an essential component designed for your Samsung refrigerator. This genuine OEM part ensures that your fridge accurately detects when the door is open or closed, maintaining optimal temperature control. By reliably triggering the cooling system, it helps prevent energy loss and keeps your food fresh longer. The switch is compatible with a wide range of Samsung refrigerator models, ensuring a perfect fit and easy installation. Its durable construction guarantees long-lasting performance, reducing the need for frequent replacements and minimizing downtime for your appliance. Additionally, a properly functioning door switch can enhance the overall efficiency of your refrigerator, contributing to lower energy bills and a more sustainable household. Whether youGÇÖre replacing a faulty switch or upgrading your fridgeGÇÖs components, the Refrigerator Door Switch provides a dependable solution to restore your refrigerator's functionality and ensure a seamless user experience.

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

The Infinite Switch is an OEM part for GE electric ranges. It regulates precise temperature settings for the bake and surface elements.  This is specifically for 6" inch elements.

Symptoms of a bad infinite switch include:

• Wide variations in cooking temperatures 
• Failure to attain or maintain desired heat levels
• Non-working or faulty temperature selector dial 

Causes can involve degraded metal contacts, worn internal components, or damaged wiring connections after extended use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore electric range models. 

This door switch detects when the dishwasher door is fully closed and latched. Replacing a worn or intermittent switch restores reliable start/stop operation and ensures the safety interlock cuts power whenever the door is opened.

• Senses door-closed status and sends a signal to the control
• Interrupts power to the machine when the door opens
• Helps prevent operation with an unlatched door
• Typical failure symptoms: won't start, stops mid-cycle if the door is bumped, or only runs when pressing on the door

• Disconnect power at the breaker before servicing
• Access the latch/switch area by removing the inner door panel or console; note wire locations
• Transfer wires one at a time and secure the new switch in the bracket
• Verify latch engagement and switch actuation before restoring power

Note: Part has been revised and may no longer include the wires. The switch is the same. Use your existing wires.

This door-activated switch detects when the oven door opens or closes and signals the appliance to control the interior light. Replacing a worn or failed switch restores dependable light operation and accurate door-status feedback.

• Senses oven door position and opens/closes the light circuit
• Controls the oven's interior light based on door position
• Provides door-status input to the control for normal operation
• Typical symptoms: light stays on, won't turn on, or flickers with door movement; door-ajar messages may appear

• Disconnect power at the breaker or unplug the unit before servicing
• Access the switch from behind the front frame or control area, depending on model
• Move wires to the new switch one at a time to maintain correct positions; secure with existing hardware
• Restore power and verify light operation with door open/closed before reassembly