Solenoid Parts

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This water inlet valve controls the flow of household water into your appliance during operation. Replacing a sticking or leaking valve restores proper filling and helps prevent unwanted water entering the unit between cycles.

• Opens and closes to regulate water flow when energized by the control
• Failure can cause no fill or very slow fill during cycles
• Can contribute to leaks at the back or water-inlet/fill error alerts

• Disconnect power and shut off the water supply before servicing
• Keep a towel or pan handy to catch residual water; relieve hose pressure
• Note/label hose and wire locations; transfer any brackets or screws from the original valve as needed
• Restore water and power, tighten connections, and check carefully for leaks with a test fill

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

This latch and handle assembly engages the oven's door lock when you move the lever, allowing self-clean cycles to start and complete safely. Replacing a worn or broken latch/handle restores smooth locking and proper door interlock function.

• Provides the manual lever and latch mechanism that locks the oven door for self-cleaning
• Interfaces with the door lock switches to signal locked/unlocked status to the control
• Common symptoms: self-clean won't start or end, door won't lock/unlock, lever is loose/stuck/broken, or a door lock/latch error is displayed
• Restores safe door security during high-heat cleaning

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Access is typically from the control panel/top or rear, depending on model—take photos of linkage and any wiring for reference
• Move connectors and mounting hardware over one at a time to maintain orientation
• After reassembly, check lever travel and the door locks/unlocks before starting a clean cycle

This motor drives the fan or mechanism in your cooking appliance to move air as designed. Replacing a worn or seized motor restores proper airflow and quieter operation for consistent baking, cooling, or venting performance, depending on model.

• Powers the appliance's fan or drive to circulate air or move exhaust
• Helps maintain even temperatures or ventilation during operation
• Replaces a noisy, slow, or non-spinning motor
• Common signs: fan won't run, weak airflow, humming/grinding noise, overheating, or a tripped breaker

• Disconnect power at the breaker; shut off gas supply for gas models
• Access location varies by model; remove the necessary panels to reach the motor
• Note wiring and rotation; transfer any brackets, grommets, or the fan blade from the original, if required
• After installation, verify smooth, quiet operation and correct airflow

Replacement inlet valve assembly that controls water entering the washer so cycles fill properly and the appliance runs as expected. Installs at the water inlet to restore proper filling and stop leaks caused by a faulty valve. What it does:

• Opens and closes the water path into the washer to allow correct fill levels during wash cycles.
• Stops or reduces water flow when the valve is closed to prevent overfilling.
• Common symptom fixes: washer won't fill, intermittent filling, continuous filling, or water leaking at the inlet connection.
• Works with the appliance's inlet hose connections and electrical solenoid controls.

• Disconnect power and turn off the home's water supply before starting any repair.
• Remove the access panel, disconnect inlet hoses and electrical connectors, then replace the valve with the correct orientation and seals.
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks.

This surface burner valve controls gas flow to a cooktop or range burner for smooth ignition and precise flame adjustment. Replacing a worn valve restores reliable lighting and consistent simmer-to-high control at the knob. What it does:

• Regulates and meters gas flow to a surface burner from Off through all heat settings
• Wear or blockage can cause no ignition, hard-to-turn knob, or poor/unstable flame
• Helps correct burners that won't adjust properly or won't stay lit
• Ensures safer, consistent burner performance when operating correctly

• 1 surface burner valve

• Disconnect power and shut off gas supply before servicing; allow appliance to cool
• Work in a well-ventilated area and follow local codes
• Note knob orientation; transfer any orifice fittings or mounting hardware from the old valve
• After installation, check all connections for leaks using a non-corrosive leak-detection solution

This dishwasher float rises with the water level to engage the float switch. It regulates filling and helps prevent overflows, protecting your kitchen from leaks and keeping wash cycles running properly. What it does:

• Rises with the tub's water level and actuates the float switch
• Signals the inlet valve to stop water flow at the correct level
• A stuck, worn, or broken float may cause overfilling or no-fill conditions
• Symptoms can include leaking from overfill or no water entering during fill

• 1 float

• Disconnect power and turn off the water supply before servicing
• Open the door; remove the lower rack for access
• Lift off any float cap/retainer, pull the old float straight up, and seat the new float
• Ensure the float moves freely; restore power/water and run a brief fill test

This dishwasher water inlet valve controls the flow of water into the tub during the fill cycle. Replacing a sticking or leaking valve restores proper filling performance and helps prevent unwanted water or leaks.

• Opens and closes to allow the correct amount of water into the dishwasher
• Works with the control/float system to stop water flow at the right time
• Typical symptoms: won't fill or fills slowly; hums but no water; leaks at the valve or hose connections; water seeping into the tub when the unit is off

• Disconnect power and shut off the water supply before servicing
• Access the valve behind the lower kick panel; label/photograph wire positions and place a towel to catch residual water
• Install in the same orientation; secure the outlet hose with the included clamp and reconnect the inlet line and wiring
• Restore water and power, run a short fill test, and check all connections for leaks

Does not include instructions.The only literature inserted is a notification stating that these valves no longer come with the harness

Note: Due to design change, new part may look different but is still a functional replacement.

Water inlet valve controls water flow to the refrigerator's dispenser and ice maker. Replacing a failed valve restores normal water delivery and can resolve symptoms like no water, weak flow, or continuous running/filling. What it does:

• Opens to allow water into the ice maker and dispenser when requested.
• Closes to stop water flow and prevent overfilling.
• Common symptoms: no water from dispenser, slow/weak water flow, or the ice maker not filling.
• Also used when leaks or intermittent water flow are traced to the inlet area.

• Disconnect power and shut off the home water supply before servicing.
• Relieve line pressure by dispensing water or gently loosening a downstream connection.
• Inspect fittings and seals; tighten connections snugly but avoid overtightening.
• After installation, turn on water and power, check for leaks, and verify dispenser/ice maker operation.

New seals come with this valve.

Valve flapper for the washer's dual-pump drain assembly that directs water between pumps for proper draining. Replacing a worn or torn flapper helps restore drain operation and reduce leaks or poor drain performance. What it does:

• Directs water flow between the washer's dual drain pumps to ensure proper draining.
• Commonly linked to symptoms such as slow or incomplete draining, water remaining in the tub, or intermittent leaks.
• Replaces a cracked, torn, or hardened flapper that no longer seals or diverts flow correctly.

• Disconnect power and turn off water supply before beginning any repair.
• Access typically requires removing the washer's front or rear access panel and the drain pump assembly—use basic hand tools.
• Test drain function with a short cycle and check for leaks.

The Water Valve is an OEM replacement part for GE dishwashers. Located inside the valve body, this electronically-controlled component precisely regulates water inlet and flow during each cycle of the wash sequence. The water valve utilizes sensors and timer modules to open and close water lines at the correct times based on cycle selections.

Symptoms of a defective water valve include:

• Failure to fill or improper filling  
• Inability to switch between cycles
• Water leaks from the valve body area
• Erratic or inconsistent water usage amounts

Causes of malfunction often stem from worn internal seals, mineral buildup obstructing valve ports over time, or issues with the electronic control board. Replace yours today with this genuine GE water valve for reliable water control, sensor functions, and trouble-free dishwasher cycles. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

Control the water going into your washer with this triple water inlet valve. Three solenoids open and close to deliver water to the correct fill circuits or dispensers so cycles start and dispensing happens where it should.

• Regulates water flow into the washer when energized by the control
• Routes water to the correct fill path or dispenser compartment via three independently controlled outlets
• Common symptoms: no fill or slow fill, only certain cycles/dispensers receive water, water drips into the tub when off, or leaks at the valve/hose connections

• Unplug the washer and shut off the water supply before servicing
• Place towels, disconnect inlet hoses, and label/photograph wire connectors and outlet hoses for correct reassembly
• Transfer any mounting hardware from the old valve if required; ensure hoses/orientation match their original positions
• Restore water and power, then check all connections for leaks and run a test fill