Tube Parts

This air brake/drain hose assembly creates an anti-siphon break in the drain line and safely routes wastewater to household plumbing. Replacing a cracked, kinked, or clogged assembly restores reliable draining and helps prevent leaks or backflow.

• Provides the air gap/vacuum break to help prevent siphoning and contamination
• Connects the dishwasher's drain outlet to the air gap or garbage disposal/inlet
• Helps keep water from backing into the tub after a cycle
• Typical failure signs: leaks, slow or no drain, water returning to tub, visible hose damage

• Disconnect power; shut off water supply and place towels to catch residual water
• Note original hose routing and clamp positions; reuse existing clamps and seals as needed
• Maintain a high loop or external air gap per local code when routing the drain line
• After installation, run a short cycle and inspect all connections for leaks or kinks

This 10-foot dishwasher drain hose routes wastewater from your machine to the sink drain or disposer. Replace a cracked, kinked, or too-short hose to restore reliable, leak-free draining and accommodate longer drain runs.

• Conveys drain water from the dishwasher to the household drain/disposer
• Helps address leaks from brittle, split, or loose hoses
• 10-foot length provides extra reach for extended routing

• Disconnect power and turn off water before service
• Route with a proper high loop or air gap per your model manual and local code to prevent backflow
• Avoid kinks; secure connections with appropriate clamps and ensure tight fits
• Run a test cycle and check all connections for leaks

This hose connector links internal water lines inside the dishwasher and maintains a secure, leak-resistant seal for proper water flow during each cycle. Replacing a worn connector helps stop leaks and keeps cleaning performance reliable.

• Joins internal water lines/components with a tight, reliable seal
• Helps prevent drips and leaks at a hose connection point
• Supports consistent water circulation through the wash system
• Typical symptoms: puddles under the unit, moisture around the base, visible cracks/swelling at the connector, or a loose fit

• Unplug the dishwasher and turn off the water supply before servicing
• Remove the toe-kick/access panel; place a towel to catch residual water
• Note hose routing and orientation; fully seat the connector and transfer/reuse existing clamps
• After reassembly, run a short cycle and inspect all connections for leaks

This washer door boot gasket (bellows) seals the opening between the outer tub and the front panel on front-load machines, keeping wash water inside the drum. Replace when the seal is torn, cracked, or leaking around the door.

• Forms a flexible, watertight seal between the tub and door opening
• Helps prevent leaks during fill, wash, and spin cycles
• Typical failure signs: water on the floor at the front of the washer
• Visible rips, cracks, or warping of the boot
• Drips or seepage from the door area after a cycle

• Unplug the washer and shut off water supply before servicing
• Remove the outer and inner retaining clamps and front panel as required by your model to access the boot
• Note the boot's orientation and alignment marks; match the same orientation on the new gasket
• Ensure the gasket lip is fully seated in the grooves; reinstall clamps evenly and securely

Size: 1 foot. This Bosch dishwasher drain hose comes with 2 o-rings. For the 5 foot drain hose order 00298564.

This pump hose and clamps create a sealed connection between the dishwasher's pump and internal plumbing. Replace when the hose is cracked or clamps are corroded/loose to stop leaks and restore a secure, watertight fit. What it does:

• Creates a sealed connection between the pump and internal plumbing
• Helps contain water flow during wash and drain operation
• Replace if the hose is cracked, brittle, swollen, or deformed
• Symptoms include water leaking under the dishwasher or loose/corroded clamps

• Disconnect power and water; pull the dishwasher forward as needed for access
• Expect residual water—protect flooring and have a towel or pan ready
• Remove old clamps and hose; fully seat the new hose on fittings, then position and secure clamps at the bead/ridge
• Run a brief cycle and check for leaks before reinstalling

This inlet hose routes fresh water into the dishwasher during the fill cycle. Replace a cracked, kinked, or leaking hose to restore proper water flow and help prevent puddles or water damage beneath the unit.

• Routes water into the dishwasher during fill
• Maintains a sealed path to help prevent leaks
• Common fix for leaks under the unit, visible cracks/kinks, or slow/no fill
• Replaces aged, brittle, swollen, or punctured tubing

• Disconnect power and shut off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing the old hose
• Note the original routing; transfer and secure existing clamps/fittings as needed
• Restore water and run a short cycle while checking all connections for leaks

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This waterline assembly supplies water from the household line to the refrigerator's ice maker and/or water dispenser, restoring reliable water flow and preventing leaks from damaged tubing. Ideal when the fridge isn't filling or water is leaking. What it does

• Carries water from the home supply to the refrigerator ice maker/water dispenser
• Replaces cracked, pinched, or leaking tubing that causes visible leaks or puddles
• Restores normal fill to the ice maker and consistent water flow to the dispenser
• Helps eliminate slow or intermittent fill issues caused by restricted or damaged lines

• One waterline assembly with attached fittings as shown

• Shut off the home water supply and unplug the refrigerator before starting
• Tighten fittings to manufacturer torque—do not overtighten plastic fittings
• Inspect existing connections and replace any damaged shutoff valves or connectors
• After installation, turn water back on and check all connections for leaks; flush line per manufacturer instructions

This gas tubing is a direct-fit replacement line that routes gas between components and restores a secure fuel path for safe burner operation. It helps stop leaks and ensure consistent gas flow to the appliance. What it does

• Replaces damaged, cracked, or corroded gas tubing that can cause leaks or loss of gas flow
• Restores a sealed connection between the gas valve and burner or between gas components
• Can resolve symptoms such as gas odor, intermittent ignition, or weak burner flame when tubing is the cause
• Designed to match OEM form and fit for straightforward replacement when listed for your model

• One gas tubing assembly as shown

• Shut off the gas supply and unplug the appliance before starting any work
• After installation, test all fittings with a leak detection solution; do not use an open flame
• Follow all local codes and OEM instructions for fittings, sealants, and torque values

This plastic extension fill tube continues the water path from the valve to the ice maker, restoring proper water delivery for ice production. It helps ensure the ice maker receives measured water without leaks or misdirection. What it does

• Extends the water fill line to reach the ice maker inlet and maintain proper fill height
• Directs metered water into the ice maker mold to form full, solid ice cubes
• Commonly replaces cracked, kinked, or detached tubing that leaks or reduces fill
• Helps stop intermittent or no-fill symptoms when the ice maker and valve are otherwise working

• One plastic extension ice maker fill tube

• Disconnect power and shut off the water supply before starting work
• Remove only panels or components necessary to access the ice maker and fill tube
• Securely seat tubing on the valve and ice maker inlet; check for kinks or contact with sharp edges
• Test for leaks and proper fill by restoring power and water, then observing one fill cycle

This flexible replacement hose routes water between appliance components to restore proper water flow and prevent leaks. It's a direct-fit service part when the original hose is cracked, split, or clogged. What it does:

• Carries water safely between the pump, valve, tank or dispenser as designed
• Restores proper drainage or water delivery when the original hose is leaking or collapsed
• Prevents water damage by replacing worn, brittle, or pinched tubing
• Helps eliminate noises and poor performance caused by restricted flow

• One replacement flexible hose

• Disconnect power and shut off the water supply before beginning any work
• Use appropriate clamps or fittings; tighten to manufacturer torque recommendations without over-tightening
• Inspect connections and run a water test after installation to check for leaks

This hose connector joins a refrigerator's/dispenser's water line to internal plumbing, restoring a secure, leak-resistant connection. It replaces cracked or worn connectors to help stop leaks and ensure reliable water flow. What it does:

• Provides a sealed connection between the water hose and the appliance plumbing or valve
• Stops leaks caused by cracked, brittle, or damaged connectors
• Restores proper water flow to the dispenser/ice maker when the connector is the failure point
• Works with hose clamps or fittings already present in the appliance plumbing

• Shut off water supply and unplug the appliance before servicing
• Inspect hose ends and replace clamps or O-rings if damaged; use proper-size clamps for a secure fit
• Hand-start threads, then tighten snugly—avoid over-tightening plastic fittings to prevent damage
• Turn water back on and check thoroughly for leaks after installation

This dishwasher sump assembly houses the pump inlet and integrated ball check valve to route wash water to the drain while preventing backflow. Replaces worn or cracked sumps to restore proper draining and prevent leaks. What it does

• Collects and channels dishwasher wash water from the tub to the drain pump.
• Integrated ball check valve stops backflow into the sump, helping prevent standing water and odor.
• Restores proper drain function when the existing sump is cracked, clogged, or leaking.
• Compatible with common Bosch/BSH dishwasher pump systems that use a molded sump with ball valve.

• One sump with integrated ball check valve (single assembly only).

• Disconnect power and water supply before starting any repair.
• Access typically requires removing the dishwasher lower kickplate and possibly tilting the unit; support the unit and follow the OEM service manual.
• Inspect surrounding seals, hoses, and pump gaskets for wear and replace as needed.