Zoneline Heater Parts

Main broil heating element for the oven, designed to restore top-heat for broiling and browning. Replaces a failed broil element so the oven can produce even, high-intensity heat during broil cycles. What it does:

• Generates the high, direct heat at the top of the oven used for broiling and browning.
• Restores proper broil performance when the element no longer heats or glows.
• Fixes symptoms such as no broil heat, uneven browning, visible burn marks, or a broken/warped element.
• Works as the primary upper heating element used in broil cycles (main oven).

• Disconnect power to the range/oven at the breaker before starting any work.
• Remove oven racks and access the element from inside the oven; element typically secures with mounting screws and terminal connectors.
• Handle terminals and sharp metal edges carefully; wear gloves and eye protection.

This defrost heater melts frost and ice buildup on the evaporator so the freezer can maintain proper airflow and cooling. Replacing a failed heater helps reduce excessive icing and restores normal cooling performance. What it does:

• Heats the evaporator coil during the defrost cycle to remove frost and ice buildup.
• Restores airflow and cooling efficiency when frost accumulation is preventing proper cooling.
• Common symptom link: heavy frost or visible ice on evaporator coils.
• Common symptom link: freezer running continuously or temperatures that are warmer than expected.

• Disconnect power to the appliance before starting any repair.
• Access the evaporator by removing the freezer rear panel; avoid sharp sheet-metal edges.
• Inspect mounting clips and wiring; replace only if damaged and reconnect all terminals securely.
• Test the heater for electrical continuity with a multimeter before and after installation; restore power and confirm the defrost cycle operates normally.

This oven heating element replaces a failed bake element to restore even, reliable oven heat for baking and roasting. It's a direct-replacement style part that heats the oven cavity when the bake function is used. What it does

• Heats the oven cavity during bake cycles so food cooks evenly
• Commonly used when the oven won't reach or hold baking temperatures
• Can fail visibly (broken or burned) or electrically (open circuit)
• Works with the oven's temperature control to maintain set temperature

• Disconnect power at the breaker before starting any repair to avoid shock.
• Handle the element carefully; connectors and terminals can be fragile.
• Confirm wire terminal fit and secure mounting; replace only with the correct OEM-style element.

Size: 8 inch. 2200 watt. Radiant.

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This radiant surface element restores proper heat to a glass-ceramic cooktop burner. When the original element burns out or develops hot spots, replacing it brings back steady, controllable heat for everyday cooking. What it does:

• Generates heat for the selected cooking zone beneath the glass top
• Works with the surface control to cycle on/off and regulate temperature
• Helps deliver even heating across cookware
• Common fix for: burner won't heat, heats slowly or unevenly, only part of the burner heats, visible damage on the element

• 1 radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Support and handle the glass top carefully to avoid damage
• Note wire locations and transfer any mounting hardware from the old element
• After reassembly, test the burner on low and high settings

This surface radiant element sits beneath the glass cooktop and generates heat for one cooking zone. Replacing a failed element restores proper heating performance and dependable temperature response on the affected burner.

• Supplies electric heat to the selected surface burner under the glass top
• Common symptoms: burner won't heat, heats weakly or inconsistently, or only part of the ring glows
• Visual damage (burn spots/breaks) or an open reading on a continuity test indicate replacement
• Similar symptoms can also result from a faulty surface switch or wiring—diagnose before replacing

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift/remove the glass top per your service manual to access the element
• Note wire positions and bracket orientation; move wires one at a time to matching terminals
• Support the glass and avoid stressing the element; test operation before final reassembly

This Miraclon heater is a direct-replacement heating element assembly that restores proper heat generation in compatible appliances. It provides reliable, OEM-matching heating performance to help your appliance reach and maintain operating temperatures. What it does

• Replaces the appliance's failed internal heater assembly to restore heat production.
• Heats quickly and evenly to support cooking, drying, or defrosting cycles (depending on appliance).
• Common symptom: no heat or weak heat during normal operation.
• Common symptom: appliance runs but items fail to warm or dry as expected.

• Disconnect power and gas before starting any repair.
• Handle the heater carefully; avoid bending or damaging terminals and mounting tabs.
• Follow the appliance service manual for access, mounting, and wiring instructions.

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

This radiant defrost heater melts ice build-up on the evaporator coil so your refrigerator can maintain proper airflow and cooling. It restores normal defrost operation and helps prevent excessive frost accumulation. What it does:

• Radiant heating element designed to melt frost and ice from the evaporator coil during the defrost cycle
• Restores airflow and consistent cooling when the evaporator has been restricted by ice
• Common symptom: visible frost or ice on evaporator or in freezer compartment
• Common symptom: poor or uneven cooling, longer run times, or a freezer that cycles abnormally

• One radiant defrost heater (single unit as shown)

• Disconnect power to the appliance before servicing to avoid shock risk
• Access typically requires removing the evaporator cover; handle evaporator fins and heater carefully
• Inspect defrost thermostat/thermistor and defrost control components while replacing the heater — replace only the failed components

Bottom-mounted bake element that provides the primary heat for baking. Replace when burned out or damaged to restore proper preheat and even baking.

• Supplies radiant heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common failure signs: no heat in bake, slow preheat, uneven results, or visible cracks/blistering on the element
• A shorted element may trip the household circuit breaker when Bake is selected

• Disconnect power at the breaker or unplug; allow the oven to cool completely
• Remove racks; take out the element's mounting screws, gently pull it forward, and move the two wires to the new element one at a time using insulated pliers
• Don't let wires slip back through the rear panel; inspect terminals for heat damage, reassemble, restore power, and test preheat

This fill tube heater keeps the ice maker's water inlet from freezing so your refrigerator can produce ice reliably. It applies gentle heat around the fill tube to help prevent ice blockages and water drips in the freezer.

• Warms the ice maker fill tube to help prevent freezing and ice buildup
• Helps maintain consistent water flow into the ice maker during fill
• Can address symptoms like no ice production, small/hollow cubes, or a frozen fill tube
• Reduces leaks at the fill spout caused by ice blockage

• Unplug the refrigerator and turn off the water supply before servicing.
• Defrost any ice in the fill tube area; avoid sharp tools that can puncture plastic.
• Route and secure the heater along the fill tube as originally installed; avoid pinching wires.
• Ensure the electrical connector is fully seated, then restore power and verify ice maker operation.

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

This kit restores your refrigerator's automatic defrost, melting frost from the evaporator so airflow and temperatures stay consistent. Use it when frost builds up and cooling performance drops in the fresh food section. What it does:

• Heats the evaporator coil during the defrost cycle to melt frost and ice
• Bimetal thermostat opens to end defrost at the correct temperature, preventing overheating
• Helps maintain proper airflow between freezer and refrigerator compartments
• Common signs include heavy frost on the back freezer wall, warm refrigerator section, or long run times with poor cooling

• 1 defrost heater and 1 defrost termination thermostat

• Unplug the appliance before service; wear cut-resistant gloves—edges can be sharp
• Remove freezer shelves/bin and rear panel to access the evaporator; photograph wiring for reference
• Clip the new thermostat to the same tubing location/orientation as the original and ensure firm contact
• Route wiring like the original, avoid damaging fins, reinstall the rear cover for proper airflow, and allow up to 24 hours for temps to stabilize

Defrost heater that melts frost from the evaporator coil so the refrigerator can maintain efficient cooling. Replacing a failed heater restores normal defrost cycles and helps prevent ice buildup that blocks airflow. What it does:

• Heats the evaporator coil during the defrost cycle to remove frost and ice buildup.
• Restores proper airflow and cooling when ice accumulation was restricting the evaporator.
• Common symptoms of a failing heater: visible frost or ice on the evaporator, freezer running warm, or extended run times.
• Works with the appliance's defrost thermostat and control to complete the defrost cycle.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Handle the heating element carefully; avoid bending or damaging the coil or terminals.
• Verify the part number matches your appliance before installation.
• If other defrost components (thermostat, control board, sensors) show signs of failure, inspect and replace them as needed.