Zoneline Heater Parts

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This heater assembly restores heat production in electric dryers so clothes dry efficiently. It replaces a failed heating element and helps return the appliance to normal drying performance. What it does:

• Heats air passing through the dryer drum so laundry dries during operation
• Replaces a burned-out or open heating element that causes no heat or weak heat
• Addresses long dry times and extended cycles when the element isn't functioning
• Works with the dryer's blower and thermostatic controls to maintain proper air temperature

• Disconnect power at the breaker before starting any repair; this part carries live voltage during operation
• Handle the heating element carefully to avoid bending or damaging the coil
• Inspect fuses, thermostats, wiring, and connectors while replacing the heater to ensure full repair
• Follow the appliance manufacturer's service instructions for disassembly and reassembly

This surface heating element restores reliable heat to a cooktop burner. Replace a failed or damaged element to bring back even, responsive heating performance and consistent temperature control for everyday cooking.

• Converts electrical power into heat for one cooktop burner
• Common fix for a burner that won't heat or only heats intermittently
• Can address uneven heating or erratic cycling at a set temperature
• Appropriate when the element shows visible damage or burned spots

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access varies by model; lifting the cooktop or removing the glass top may be required
• Handle the element carefully and avoid stressing the heating surfaces
• Move wires one at a time to matching terminals; ensure all connections are secure before reassembly

This 8-inch Haliant radiant surface element mounts beneath the glass of a smooth-top range to heat a single cooking zone. Replacing a failed element restores proper heating response and consistent performance on that burner. What it does:

• Heats the 8-inch cooking zone by converting electrical energy to radiant heat beneath the glass
• Helps provide even heating and smooth simmer-to-boil control
• Works with the surface control to cycle and maintain the set temperature
• Typical failure symptoms: no heat, very slow heating, or inconsistent/uneven heating on that burner

• 1 Haliant 8-inch radiant surface element

• Disconnect power at the breaker; allow the cooktop to cool fully
• Lift/remove the glass top per your model's procedure to access the element
• Note wire locations and transfer any mounting clips/brackets from the old element if needed
• After reassembly, test the burner; if it still won't heat, the surface element switch/control may be at fault

1200w. Size: 6 inch. Location: Left front, right rear, and left rear.

This 12-inch defrost heater melts frost and ice from the evaporator so your refrigerator can run efficiently and keep food at the proper temperature. It replaces a failed heater to restore normal automatic defrost cycles. What it does:

• Warms the evaporator coils during the defrost cycle to remove frost and ice buildup
• Helps prevent reduced cooling and frost accumulation on the evaporator
• Commonly used when the freezer/back wall has visible ice or when defrost cycles fail
• Works with the fridge's existing defrost control/timer and thermostat to clear ice safely

• One 12-inch defrost heater

• Disconnect power to the appliance before starting any repairs
• Access usually requires removal of the evaporator cover; handle the evaporator and wiring carefully
• Verify correct heater orientation and secure connections; do not force or kink the element

Restore top-heat performance with this 240V broil element. It provides the intense overhead heat needed for broiling and finishing, replacing a burned-out or damaged element so your oven broiler works reliably and browns evenly again.

• Supplies the oven's top heat source for broiling and quick browning
• Common failure signs: broiler won't heat, uneven browning, visible breaks/blisters, or a breaker trip when broil is selected
• 240V design for standard residential electric ranges and wall ovens
• Replacing an open/weak element restores proper broiler operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; unfasten the element mounting screws and gently pull the element forward
• Transfer the two wires to the new element one at a time; do not let wires slip back through the liner
• Reinstall and secure; ensure terminals are tight and the element isn't touching oven surfaces before restoring power and testing

This thaw heater is the evaporator defrost heating element that melts frost during the refrigerator's defrost cycle. Replacing a failed heater helps restore normal defrosting and reduce frost buildup that can restrict cooling. What it does:

• Heats the evaporator coil during the defrost cycle to melt accumulated ice
• Prevents excessive frost buildup that can block airflow and reduce cooling efficiency
• Common symptoms of a failing heater: heavy frost or ice on the evaporator/back wall, reduced cooling, or long compressor run times
• Works as part of the appliance's defrost system alongside the defrost thermostat and control

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels and the evaporator cover; handle the evaporator and wiring carefully
• Inspect associated defrost components (thermostat, timer/control) if problems persist; replace only parts confirmed faulty

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

Restore reliable oven heat with this bake element. It produces the lower-oven heat during the Bake cycle, so replacing a failed element brings back normal preheat times and consistent, even results.

• Supplies primary heat from the bottom of the oven during Bake
• Common fix for: no heat on Bake, very slow preheating, uneven baking/browning
• Replace if the element is blistered, cracked, pitted, or has visible breaks
• Helps restore accurate, stable baking temperatures

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; take out the element's mounting screws to free the bracket
• Gently pull the element forward; transfer one wire at a time using insulated pliers and prevent wires from slipping back
• Re-secure the bracket/screws, ensure snug connections, restore power, and test Bake

Replacement dryer heating element that produces the hot air needed for normal drying. Replaces a failed or burned-out heating coil so the dryer can heat properly and clothes will dry in expected cycles. What it does

• Produces heat for the dryer by replacing the oven-like heating coil inside the element housing.
• Common symptoms include no heat, weak or inconsistent heat, or items taking much longer than normal to dry.
• Restores proper heating when the element coil is broken, burned, or open; does not address unrelated electrical or control faults.

• Disconnect power at the breaker or unplug the dryer before beginning any repair.
• Part installs behind the dryer access panel(s); some panel removal and basic hand tools are typically required.
• Avoid contact with sharp sheet-metal edges and the heating coil surface; allow the dryer to cool completely before handling.

This broil element delivers the high, direct heat the oven needs for broiling and finishing foods quickly and evenly. Replace a broken or burned element to restore upper-oven broil performance and consistent browning. What it does:

• Heats the oven's broil zone to provide the direct, high-temperature surface heat used for broiling and browning.
• Replaces a visibly broken, burned, or non-glowing element that prevents the oven from broiling.
• Helps eliminate uneven browning or lack of top-heat when the element fails.
• Works as the OEM-design replacement for compatible Whirlpool oven models when the original broil element no longer functions.

• One broil element

• Disconnect power to the appliance at the breaker before beginning any repair.
• Access typically requires removing the oven cavity racks and broil shield or the back panel to detach the element terminals.
• Handle the new element carefully and reconnect terminals securely; avoid forcing the element into place.

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This broil element is the oven's upper heating element that provides direct, high-heat cooking for broiling and browning. It restores the oven's broil function so foods brown evenly and cook from above. What it does:

• Heats the top of the oven cavity to produce direct radiant heat for broiling and browning
• Replaces a damaged, burned out, or non-heating upper oven element
• Commonly used when broil cycles fail or food doesn't brown on top
• Works with ovens that use a straight tubular broil element design

• Disconnect power to the range at the breaker or unplug before starting
• Element mounts with two screws accessible from inside the oven; handle glass and trim carefully
• Verify electrical connections are tight and correct before restoring power

The Refrigerator Heater Metal Sheath is essential for maintaining optimal temperature control in your refrigerator. This genuine OEM part is designed to protect the heater element, ensuring efficient operation and extending the lifespan of your appliance. Crafted from durable materials, the Heater Metal Sheath safeguards against wear and tear, preventing potential damage and maintaining consistent heating performance. Compatible with a variety of Samsung refrigerator models, it offers a secure fit and straightforward installation, making it an excellent choice for DIY repairs. By replacing a worn or damaged sheath with this genuine OEM part, you can restore your refrigerator's functionality, ensuring your food stays fresh and temperatures remain stable. This reliable component supports the overall efficiency of your appliance, providing peace of mind and enhancing your kitchen's performance. Choose the Refrigerator Heater Metal Sheath for a dependable solution that upholds the quality and functionality of your Samsung refrigerator.

This is the oven's bottom/bake heating element that provides the radiant heat used for baking and roasting. Replacing a failed element restores proper oven heating and helps return cook performance to normal. What it does:

• Heats the oven cavity during bake and roasting cycles so food reaches set temperatures.
• Failsafe indicator: oven won't reach or hold set temperature or baking is uneven.
• May show visible signs like breaks, blistering, or no glow when the oven is on.
• Restores even heating when the element is the source of the problem.

• Always disconnect power to the appliance at the breaker before starting work and allow the oven to cool completely.
• Access may require removing oven racks and the back panel or interior panel; handle the element gently to avoid damage.
• Inspect terminal connections for corrosion and tighten or replace fasteners as needed.