Slow Snowblower Spark Plug Parts

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This sump cover sits over the dishwasher's pump inlet, acting as a protective guard. It helps keep debris out of the pump, maintains proper water circulation, and protects internal components for consistent cleaning performance. What it does:

• Covers the pump/sump intake to screen larger food particles
• Helps prevent debris from entering the wash pump
• Aids proper water flow to support spray pressure and cleaning
• Common symptoms of a failed cover include poor cleaning, unusual pump noise, and visible damage or warping

• 1 sump cover

• Disconnect power and water supply before servicing; allow the unit to cool
• Remove the lower rack and spray arm or access parts as needed to reach the sump
• Release retaining screws or tabs; note the cover's orientation for reassembly
• Seat the new cover fully and secure it; hand-spin the spray arm and run a short test cycle to check operation

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

This dishwasher detergent dispenser assembly stores detergent and releases it at the correct time in the wash cycle to ensure consistent cleaning results. Replacing a worn dispenser restores reliable soap release and helps improve wash performance.

• Holds detergent and opens when signaled by the control
• Common symptoms: detergent cup won't open, soap left in the cup after cycle, broken dispenser door/latch

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to access the dispenser
• Release locking tabs, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser evenly, reinstall screws, restore power, and run a test cycle

This replacement dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle, while also controlling rinse-aid dosing. It restores reliable cleaning performance when the original dispenser is damaged, leaking, or won't open.

• Holds detergent securely and opens on command during the wash cycle
• Meters rinse aid during the final rinse to help reduce spots and film
• Seals to the inner door at the dispenser opening to help prevent leaks
• Typical symptoms: detergent left in cup, dispenser door won't latch/pop open, rinse aid not dispensing or leaking, visible cracks or warping

• Disconnect electrical power and turn off water supply before servicing
• Open the door and remove inner-door panel screws to access the dispenser
• Unplug the wire connector(s), release retaining screws/tabs, and remove the old dispenser
• Clean the door cutout, seat the new gasket evenly, secure the dispenser evenly, reconnect wiring, and run a leak check

Note: Check Serial Number for correct part

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

This actuator arm is the mechanical lever inside the dishwasher door's dispenser assembly. Working with its spring, it releases the detergent cup at the proper point in the cycle to restore consistent detergent dispensing. What it does

• Transfers motion from the control/drive mechanism to the dispenser latch to open the detergent cup
• Provides the spring tension needed for the lever to return to its home position
• Helps ensure detergent is dispensed at the intended time in the wash cycle
• Common symptoms include detergent left in the cup, a dispenser door that won't latch or opens inconsistently, or a visibly broken/missing lever

• 1 actuator arm with spring

• Disconnect power to the dishwasher before servicing
• Open the door and remove the inner door panel fasteners to access the dispenser linkage
• Note the spring orientation; move the spring to the new arm if needed and seat the arm in the correct pivot location
• Reassemble the door and manually test the dispenser action before running a cycle

Wax motor for detergent/rinse-aid dispenser.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This is the small trim cap that snaps over the end of a refrigerator door handle. It finishes the handle, covers the mounting hardware, and helps keep the handle secure and looking clean.

• Covers exposed door-handle screws and mounting points
• Restores a finished appearance if the original cap is missing or damaged
• May help reduce handle looseness if the old cap no longer held properly
• Common symptoms: missing end cover, visible handle screws, loose or rattling handle

• Unplug the appliance before starting and open the door for access
• Remove the old cap by gently prying at the seam; avoid scratching the door finish
• Align the new cap with the handle end and press until it snaps fully into place
• If required, tighten handle mounting screws before installing the cap

This dispenser assembly replaces a refrigerator's door-mounted ice and water dispenser to restore normal dispensing and reduce leaks or delivery issues. It provides the core housing and user-facing dispenser opening for door-based dispensing systems. What it does:

• Directs water and ice from the door dispenser to the user, forming the visible dispensing opening and housing.
• Helps stop common dispenser symptoms such as water dripping from the dispenser opening or ice/jam buildup at the dispenser chute.
• Supports normal push-lever or paddle operation and routes water/ice to the exterior dispense area.

• Disconnect power and shut off the water supply before starting any work.
• Removal typically requires taking off the refrigerator door panel or trim to access mounting fasteners—retain all hardware and note fastener locations.
• Handle the dispenser housing carefully to avoid cracking plastic or damaging seals; inspect gaskets and fittings and replace if brittle.

This spacer sets the correct gap and alignment between appliance components so panels, brackets, or handles mount securely and operate quietly. Replacing a worn or missing spacer helps prevent rubbing, noise, and premature wear. What it does:

• Maintains proper clearance between mating parts for accurate alignment
• Positions mounting hardware at the correct depth
• Helps prevent rattling, rubbing, or uneven gaps
• Replaces a missing, cracked, warped, or heat-damaged spacer

• 1 spacer

• Disconnect power and allow the appliance to cool before service
• Note the original order/orientation of washers and spacers during disassembly
• Install the new spacer in the same position; reuse hardware if undamaged
• Tighten fasteners evenly and avoid overtightening; verify clearances before restoring power

The Dishwasher Rinse Aid Dispenser is an essential component for maintaining spotless and efficiently dried dishes in your Samsung dishwasher. This genuine OEM part ensures optimal performance by releasing the right amount of rinse aid during each wash cycle, which helps to prevent water spots and improve drying results. Designed specifically for Samsung dishwashers, this dispenser guarantees a perfect fit and seamless integration with your appliance. The high-quality materials used in its construction provide durability and reliable operation, ensuring that your dishwasher continues to perform at its best for years to come. Installing the Dishwasher Rinse Aid Dispenser is straightforward, allowing you to quickly restore your dishwasherGÇÖs functionality without any hassle. By using this genuine OEM part, you can trust that your dishwasher will operate smoothly, delivering clean and sparkling dishes every time. Enhance your dishwashing experience with the Dishwasher Rinse Aid Dispenser and enjoy the benefits of a well-maintained appliance that efficiently handles your kitchen needs.

This lever connects to the dishwasher detergent dispenser mechanism and actuates the cup lid. A worn or damaged lever can prevent the dispenser from opening at the right time, reducing wash performance.

• Transfers motion from the timer/actuator to release the detergent cup lid
• Common symptoms: detergent remains in cup, soap door won't open, poor cleaning results
• Restores reliable dispenser operation during the wash cycle

• Disconnect power and turn off water before servicing
• Access typically requires removing the inner door panel to reach the dispenser linkage
• Note linkage orientation before removal; transfer any springs or clips
• Test dispenser door movement by hand before reassembling

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.