Solenoid Parts

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more

1.) Located where the water leak was coming from in the refrigerator. 2.) Unplugged the refrigerator. 3.) Shut off the water supply to the refrigerator. 4.) Unscrewed the back cardboard panel. 5.) Unscrewed the Water Valve attached to the side of the refrigerator (one screw). 6.) Disconnected the three electrical plugs on the water valve. The plugs are different sizes so there is no need to worry about reconnecting incorrectly. 7.) Disconnected the two water lines by pushing down on... Read more

Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

I ordered a new solenoid valve set and watched the online video of the replacement process. So after emptying my freezer and fridge, removing the doors and freezer drawer, so I could mover the fridge out of its cove, I discovered after taking the panels off the rear, that my fridge is different than that shown in the video. I went back online and discovered in one of the exploded views of the cabinet there is a panel inside the refrigerator which can be removed after taking the shelves out of... Read more

• Will not fill with water
• Will not stop filling with water

The F20 code was low/no water pressure code. I watched a YouTube video and purchased a Water Inlet Valve from Appliance Pros. After my son installed the new part my washer still didn't work. I looked on Google for trouble shooting and the 1st thing it said was turn on both hot/cold water as the washer needs the pressure of the hot/cold water. I had turned off the hot valve because it was leaking. I assumed I could still do cold water loads. Read more

Replaced icemaker Read more

Replacement was easy and it works as it should. Thank you for your guidance. Read more

I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more

Replaced the cheap plastic lever supporter with another LG OEM cheap plastic lever supporter. I should have bought two as I can see this problem happening again. Job was a simple fix and only required a Phillips head screwdriver. I did not need to remove any connections as there was enough room and wire to pull out the oven control assembly and make the repair. One word of caution is to be careful as the sheet metal internal cover and bottom of the control knob panel is razor... Read more

Replaced water mixing valve. Read more

First - shut off water valves & unplugged electric. Second - opened up back of washer & removed top part as well. Third - turned hot & cold water back on one at a time to see where the leak was coming from...lucky for me it was the inlet valve which was right there at the back of washer. Turned water off again. Fourth - located part on internet - and found you & ordered part but not before I went to Lowe's and called local appliance part stores to see if I could find...did not...came home and... Read more

• Will not fill with water

Removed the old one. ordered a new one from appliancepartspros.com on Thursday afternoon, had the part on my front porch by Friday afternoon and installed it the next Monday morning. After I determined the problem, actual time fixing was maybe 30 minutes. Read more