Kenmore Refrigerator 106.51212100 (10651212100, 106 51212100) Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Not dispensing water

Our Kenmore (Whirlpool) refrigerator's ice maker had stopped making ice. I searched YouTube and found a repair videos for this exact problem, finding one with a similar refrigerator and the identical ice maker. I learned that the Water Inlet Valve had likely gone bad and would need to be replaced. In the video the tech pointed out the small rubber tube inside the freezer that comes down from the ceiling of the refrigerator into the ice maker. This tube feeds it the water to make ice with and... Read more

• Ice maker dispenses too little ice
• Ice maker dispenses too much ice
• Ice maker won't dispense ice
• Ice maker not making ice

Replace assembly Read more

Installed replacement drawer Read more

• Frost buildup
• Freezer not defrosting
• Freezer section too warm
• Fridge too warm

Condenser was encased in solid block of ice due to automatic defrost not working. Replaced thermostat and ADC control board. Working fine now. Most tedious part was using a heat gun to melt all the ice off the condenser coils. You will need a couple small wire nuts to splice the new thermostat into the existing harness (they are not included). Service tech wanted over $400 to repair, fixed it myself for half that. Thanks ! Read more

• Door sweating
• Door won't open or close
• Clicking sound
• Fridge too warm

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

Took broken bin out and replaced with new one. No tools were required ( for the next section since it won't allow me to only select other). Read more

• Fridge too cold
• Fridge runs too long
• Won't start
• Freezer section too warm

The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a... Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

• Door won't open or close
• Door sweating
• Fridge too warm
• Noisy

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

• Too warm
• Fridge runs too long
• Fridge too cold
• Frost buildup

A word of thanks to AppliancePartsPros - they delivered in one day. Ordered at 4PM CDT and received the part by noon the next day. Also, Alicia in the help department was able to locate an electrical diagram for my old freezer. This was essential for proper setup and her persistence in tracking down the diagram was top notch. Now on to my problem. One day I opened the freezer and found frost and thawing food. I attributed this to the door hitting an item in the freezer and not completely... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

First Problem - WATER INLET VALVE - After having problems with ice maker not making ice, I troubleshot and replaced the water inlet valve. Video and instructions were excellent. With 16 year old fridge, the water lines had compression fittings in the old valve, so had to cut the fittings off with a razor blade to allow the lines to insert into the new valve press-in type fittings. Worked great / no leaks at the new valve. But, new leaks occurred at the water filter housing spraying down into... Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

• Ice maker not making ice
• Ice maker won't dispense ice

SO I FIGURED THAT ALL THE MECHANICAL PARTS OF IT WERE FINE SO THE LOGICAL THING TO DO WAS TO REPLACE ELECTRICAL COMPONENTS WHICH CONSISTED OF THE THERMOSTAT {THE BRAIN} AND THE CONTROL MODULE WHICH I PURCHASED AT A VERY REASONABLE PRICE . I REASSEMBLED THE UNIT AND IT HAS BEEN WORKING LIKE NEW EVER SINCE. THANK YOU! Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more