Huskee / Husky Snowblower Regular Starter Parts

• Doesn't shut off
• Won't start
• Will not tumble

I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter.... Read more

I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more

• Doesn't shut off
• Won't start

I watch the video on YouTube. And it went step by step on how to take it off and on Read more

• Won't start

Noticed Rolls on the top shelf no longer frozen, though the meat around it still was. Note: This is a good test, keep something that thaws quickly and is not expensive on top shelf, to act as a barometer for your freezer health! I first found a trip online to advance the defrost timer, as a failed timer is a common issue. I advanced the timer, but nothing happened. I emptied the freezer, then removed the thermostat and tested it. No continuity! With the Freezer continuing to thaw, I... Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

• Clicking sound
• Won't start
• Freezer section too warm
• Fridge too warm

Removed back cover and installed new start device. Plugged in refridgerator and it runs like new. Read more

• Won't start
• Too warm
• Fridge too warm
• Freezer section too warm

In short - I replaced the evaporator fan motor and the evaporator fan blade. The Appliance Parts Pros website was extremely helpful to me. Here's how. 1. The site helped me identify that even though my Freezer says it's a Frigidaire, it's actually an Electrolux. 2. The site identified the potential screech causing parts. (I didn't take a chance, I bought all three) It was a worthwhile investment. My freezer is 20 years old so it deserved some help. 3. The site provided guidance videos (not... Read more

The help tech helped me troubleshoot what the problem might be, and we narrowed it down to a faulty switch. He helped us pick the right part, and the video was helpful - it gave me the confidence that I could fix it myself. The part came, and it only took me 5 minutes to change out the switch. Now my dryer works great! I saved my wife $500 for a new dryer! :) Read more

We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

• Won't start

Looked at the diagnostic help on Appliance Parts Pros.com and the start switch was the problem, but only 25% of the time, so I was a little concerned it may be a different problem. The switch was reasonably priced, so I ordered it and it arrived in two days! It was very easy to follow the repair video, however, my GE Gas dryer had a lot of screws rather than 2 screws and tabs on the model in the video, so it took a little more time to open up. After turning off the gas and unplugging the... Read more

• Doesn't shut off

Background: Roper Electric Dryer model REX6634RQ0 purchased new in early 2006 by my wife. Dryer use profile is low to moderate as it was used by only one person (working from home) from 2006 to late 2007 then moved and stored in a dry basement until mid 2009. Moved and used by primarily just two people (plus occasional children visits) from mid-2009 thru late 2011 with three moves involved with in that time. Then stored in a dry shipping container until moved again in 2013. The multiple... Read more

Replaced the starter and capacitor, 30minutes, $60.... Bam!!! Fixed Read more

• Doesn't shut off
• Won't start
• Will not tumble

The timer knob simply pulls off the shaft with a solid, steady pull. Cleaned the timer cavity of lint/dust buildup. Aligned the keying flat of the shaft and knob and pushed the new knob on with careful, steady pressure until it was obviously seated. No tools required other than a vacuum. The door switch would sometimes not shut the dryer off when the door was opened. New switch came with new fast-on connectors. Replacement required opening the top cover of the dryer and hinging it up. This... Read more

Replaced the duct tape with a new switch Read more