Wsm2700rdwwh Parts

The Dryer Belt is an OEM part for GE dryers. This belt wraps around the drum, motor pulley, and tension pulley, enabling the drum to spin during the drying cycle. It plays a crucial role in the mechanical operation of the dryer.

Common causes of a bad dryer belt include normal wear and tear from repeated use, overloading the dryer, or damage from obstructions inside the drum.

Symptoms of a bad dryer belt include:

• The drum not turning when the dryer is running
• A burning smell during operation
• Unusual noises such as thumping or squeaking
•  The dryer stopping mid-cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Washer Fill Hoses are OEM parts for various washing machines, specifically designed to transport hot and cold water from the home's supply lines to the washer. These hoses are essential for the proper functioning of the washing machine, ensuring a steady and reliable flow of water during the wash and rinse cycles. Coming in packs of 2, each hose measures 5 ft.

Causes of bad washer fill hoses can include wear and tear over time, exposure to high water pressure, or damage from kinks and bends. Additionally, hoses can deteriorate due to exposure to harsh water conditions or chemical buildup.

Symptoms of bad washer fill hoses include:

• Leaks or puddles around the washing machine
• Reduced water flow into the washer
• Visible cracks or bulges in the hoses
• The washer taking longer than usual to fill with water

These washer fill hoses are compatible with a variety of washing machine brands and models, ensuring a secure and efficient water supply.

The V Belt is an OEM part for GE washing machines. This belt connects the drive motor to the washer's drum, facilitating the rotation of the drum during the wash and spin cycles. 

Causes of a bad V belt can include wear and tear from continuous use, stretching, fraying, or snapping due to overloading or improper installation. 

Symptoms of a bad V belt include:

• The washer drum not spinning or agitating
• Unusual noises, such as squealing or slapping, during operation
• A burning rubber smell coming from the washer
• The washer stopping mid-cycle or not completing cycles properly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This dryer safety thermostat monitors internal temperature and opens the circuit if the unit overheats, protecting the heater and wiring. Replacing a failed thermostat restores proper over-temperature cutoff and safe, consistent drying performance. What it does:

• Monitors air temperature at the heater/exhaust path
• Interrupts power to the heating element if temperatures exceed its limit
• Helps prevent overheating and thermal damage
• Common symptoms can include: no heat, heat cutting out early or overheating, or the dryer shutting off on high heat

• 1 safety thermostat

• Disconnect power before service; for gas dryers, also shut off the gas supply
• Typically mounted on the heater housing or exhaust duct; note wire positions and transfer one at a time
• Secure with existing hardware and ensure tight electrical connections
• After replacement, clean the lint filter, vent hose, and exhaust duct to ensure proper airflow and prevent repeat overheat trips

This replacement heating element restores proper electric heat inside the dryer so clothes dry consistently and on time. A worn or open element can leave loads damp or extend cycle times; swapping it brings heat output back to spec.

• Generates the electric heat used during drying
• Common failure signs: no heat, long dry times, partial heating, or tripping the thermal cutoff
• Visual cues can include broken/warped coil or obvious burn spots
• Restores normal temperature rise for even drying performance

• Disconnect power before servicing; elements run on high voltage
• Access typically from the front or rear depending on model; note wire positions
• Avoid touching the coil with bare hands; handle by the frame
• Inspect thermostats/thermal cutoff if the old element failed

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This dryer blower wheel mounts on the motor shaft to move air through the drum, lint filter, and exhaust duct, helping maintain proper airflow, even drying, and overall dryer performance.

• Moves air through the drum, lint screen, and duct to exhaust moisture and lint
• If the hub is stripped or the wheel is loose on the motor shaft, airflow drops and dry times increase
• Cracked, warped, or broken fins can cause rattling, scraping, or vibration during operation
• Common symptoms include weak air at the vent, longer cycles, or unusual noise from the lower/front cabinet area

• Disconnect power; if gas, also shut off the gas supply. Wear gloves—sheet-metal edges can be sharp
• Access the blower housing by removing the front/lower panel and blower cover as your model requires
• Note thread direction and any retaining nut/clip when removing; transfer any reusable hardware to the new wheel
• Clear lint and debris from the blower housing and ducts; ensure the new wheel spins freely without rubbing before reassembly

Replace a failed dryer timer to restore reliable cycle selection and timing. This dryer control advances the machine through selected cycles so loads run and finish on the chosen program. What it does

• Advances the dryer through cycle steps and governs timed run lengths.
• Used for selecting timed and automatic cycles; coordinates cycle changes.
• Common symptoms: timer won't advance, dryer stays on one cycle, or cycles don't complete.
• Replace when the timer knob fails to turn or cycles no longer respond to controls.

• Disconnect power (unplug or shut off the breaker) before servicing to avoid electric shock.
• Access usually requires removing the control panel and unplugging the wiring harness; keep track of fasteners and connector locations.
• On gas dryers, shut off the gas supply before starting any work.

Includes 12 washers.

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run

For complete bearing kit order WE25X10001.

This plug is an electrical wire connector that restores a secure, insulated connection between appliance wiring and components. It helps prevent intermittent power loss and reduces the risk of shorts from damaged or loose wiring. What it does:

• Provides a secure mating point for a component or harness to carry electrical power
• Insulates and protects exposed terminals from contact and shorting
• Replaces cracked, melted, or loose connector housings that cause intermittent operation
• Commonly used when a control, sensor, or motor has lost power due to a failed connector

• Always disconnect power at the breaker or appliance plug before inspecting or replacing electrical connectors
• Match the connector shape and terminal count to the existing harness to ensure proper fit
• Inspect surrounding wiring and terminals for heat damage; replace any damaged wires or terminals to prevent recurrence

This replacement part is a dryer clip, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This dryer clip is typically found on dryers and there are usually multiple clips on one appliance. These clips help hold the front panel in place and secure so that it does not come off during the drying cycle. A new dryer clip might be needed if the front panel of the dryer is off balance or not attached correctly. It is possible that the clips can become loose over time as the appliance is prone to shaking and vibrating. The clips are important as it keeps the dangerous parts covered. If the entire front panel can be lifted off then it is time to replace the dryer clips. These clips are sold individually even though dryers typically have more than one. This clip is a genuine OEM part.

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.