Parts for Kenmore 110.67132410 (11067132410, 110 67132410): Top And Console Parts

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This mounting bracket secures and supports appliance components to keep panels and internal parts aligned for reliable operation. It prevents shifting and reduces noise caused by loose or damaged supports. What it does:

• Secures panels or assemblies to the appliance frame to maintain alignment
• Prevents movement that can cause rattling, vibration, or uneven operation
• Replaces cracked, bent, or worn brackets that fail to hold components firmly
• Restores proper fit where mounting points were compromised

• One mounting bracket

• Disconnect power (and water if applicable) before starting any repair
• Use the original fasteners when possible; replace damaged hardware as needed
• Tighten to a snug fit—do not overtighten and strip mounting holes

This mounting bracket secures and supports appliance components to keep panels and internal parts aligned for reliable operation. It prevents shifting and reduces noise caused by loose or damaged supports. What it does:

• Secures panels or assemblies to the appliance frame to maintain alignment
• Prevents movement that can cause rattling, vibration, or uneven operation
• Replaces cracked, bent, or worn brackets that fail to hold components firmly
• Restores proper fit where mounting points were compromised

• One mounting bracket

• Disconnect power (and water if applicable) before starting any repair
• Use the original fasteners when possible; replace damaged hardware as needed
• Tighten to a snug fit—do not overtighten and strip mounting holes

This replacement nut secures appliance parts and hardware to keep assemblies stable and prevent loose connections. It's a simple, direct replacement for worn or missing fastening hardware to restore proper fit and reduce vibration. What it does:

• Fastens mounting studs, brackets or panels to hold components in place
• Restores secure mechanical connections that can loosen over time
• Helps eliminate rattling, vibration and misaligned panels caused by missing or stripped hardware
• Provides a straightforward, durable replacement for corroded or damaged nuts

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket; ensure threads engage smoothly before tightening
• Tighten until snug—avoid overtightening that can strip threads or damage components
• Inspect mating threads and replace any damaged studs or hardware for a reliable repair

This replacement screen filters debris within your appliance to help protect internal components and maintain proper performance. A clean, intact screen supports consistent flow and reduces the risk of clogs or premature wear.

• Traps debris to help prevent clogs in the designated flow path
• Helps protect downstream parts such as valves, pumps, or passages
• A torn, missing, or clogged screen can contribute to reduced performance, unusual noises, slow flow, or error codes
• Restores proper flow when replaced with a new, clean screen

• Disconnect power and, if applicable, shut off water or gas before servicing
• Access the screen per your model's service information and note its orientation
• Clean the mating area and remove any debris before installing the new screen
• If the original screen used an O-ring or seal, transfer it if reusable or replace as needed; seat fully and check for leaks or proper operation

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

This console is the replacement control panel housing that covers and supports your appliance's user controls, restoring a clean appearance and proper button/knob alignment for reliable operation. What it does

• Replaces a cracked, broken or damaged control panel housing that exposes switches or wiring
• Provides a stable mounting surface for buttons, knobs and the control board
• Helps prevent dirt and moisture from reaching internal electronics
• Restores proper alignment so controls actuate correctly and safely

• Disconnect power before beginning any repair to avoid shock or injury
• Basic hand tools are usually required; remove trim or screws to access the original console
• Handle edges and mounting tabs carefully to avoid damage during installation
• Test that all controls operate correctly after reassembly; for exact steps

Specs: 10-16 x 1/2 inch.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.