Parts for Ge WPDH8900J2MG: 04 - Tub & Motor Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This wire harness assembly routes power and control signals between the appliance's components, restoring lost or intermittent electrical connections for reliable operation. It replaces damaged or burnt wiring and worn connector ends. What it does:

• Provides factory-style electrical connections between controls, motors, switches, and sensors
• Restores power and signal continuity when original wiring is frayed, cut, or corroded
• Helps stop intermittent operation, no-power conditions, or arcing caused by damaged wires or connectors
• Maintains correct wire routing and connector fit to prevent chafing and short circuits

• Disconnect power (unplug or shut off breaker) before starting any repair
• Compare the new harness to the original to ensure connector types and lengths before installing
• Route wires along original clips and channels; avoid contact with sharp edges or hot surfaces
• If connectors are corroded or damaged, replace them rather than splicing; follow OEM instructions

Small self-tapping screw used to secure appliance panels and internal components. Replaces worn or missing fasteners to restore proper fit and alignment for covers, brackets, and trim pieces. What it does

• Secures sheet-metal panels, brackets or trim to the appliance chassis
• Replaces stripped, corroded or missing screws that allow rattling or loose parts
• Helps restore proper panel alignment and prevents vibration noise
• Works where a self-tapping thread is required in thin metal or plastic mating parts

• Power off and unplug the appliance before servicing
• Use the correct screwdriver bit to avoid cam-out and head damage
• Start threads straight and drive carefully—do not overtighten to avoid stripping
• Replace like-for-like; match screw length and thread type to the original

This M8 hex nut is a standard threaded fastener used to secure components and panels. It restores proper clamping force for connections that have come loose, helping eliminate movement and intermittent contacts. What it does:

• Secures bolts, studs, and mounting hardware to hold parts and assemblies in place
• Restores tight mechanical connections that can prevent rattling or misalignment
• Helps maintain electrical grounding and stable joins where a nut is required
• Commonly used wherever an M8 threaded connection is specified by the manufacturer

• One M8 hex nut

• Disconnect power to the appliance before servicing; follow all safety guidelines
• Replace only with the correct size and thread type for a safe fit
• Hand-start threads to avoid cross-threading, then tighten to appropriate torque (do not overtighten)
• If the nut fastens components related to gas, water, or electrical systems, ensure those utilities are turned off and tested according to local codes

This flat metal washer provides a simple, durable spacer or load distributor for fasteners on select GE clothes washers. It helps maintain secure connections and proper spacing to prevent loosening and uneven loading during operation. What it does

• Distributes bolt or screw pressure to protect mating surfaces and prevent pull-through
• Maintains correct spacing and alignment for assemblies that use small fasteners
• Helps reduce loosening from vibration that can cause noise or misalignment
• Commonly used where a thin, durable washer is needed in washer assemblies

• Disconnect power and unplug the appliance before starting any repairs
• Turn off water supply when working near water lines or tub assemblies
• Use the correct size fastener and torque to avoid over-compressing the washer
• Inspect mating parts for damage and replace any worn hardware to ensure a secure repair

This gasket nozzle washer is a small rubber seal that fits at a spray/nozzle connection to help prevent leaks and ensure proper water flow. Replacing a worn gasket restores a secure seal and reduces dripping or pooling. What it does:

• Seals the connection at a spray nozzle or outlet to help stop leaks
• Maintains correct water flow through the nozzle for effective spraying
• Commonly replaces hardened, cracked, or flattened gaskets that allow dripping
• Helps eliminate minor water pooling or visible leaks near the nozzle area

• Turn off power and water supply to the appliance before servicing
• Remove the nozzle or fitting per the manufacturer's instructions; replace the old gasket with the new washer, ensuring it seats evenly
• Inspect mating surfaces for debris or damage before reinstalling

This door gasket replaces a worn or damaged refrigerator door seal to help restore a tight closure and improve cooling performance. It creates a consistent seal around the door edge to reduce air leaks and frost buildup. What it does:

• Seals the refrigerator/freezer door edge to keep cold air in and warm air out
• Helps prevent frost buildup and condensation inside the compartment
• Reduces compressor run time caused by air leaks around the door
• Often needed when the seal is torn, warped, compressed, or no longer magnets properly

• Disconnect power to the appliance before starting any service
• Remove the old gasket by loosening retaining screws or popping out mounting retainer
• Clean the mounting channel of debris and adhesive residue before installing the new gasket
• Align the new gasket around the door, secure the retainer if applicable, and press firmly to seat; warm the gasket with a hair dryer on low if needed to help it conform

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

GE Front load washer drum belt. Size: 48.4 inches at rest postion and 51.2 inches when working.

This motor assembly kit replaces a worn or failed motor to restore proper mechanical drive and motion in the appliance. It's a direct-fit replacement designed to match the original assembly's form and function. What it does:

• Replaces the appliance's motor assembly to restore spinning, stirring, or drive motion
• Stops symptoms like no movement, intermittent operation, or unusual humming from the motor area
• Restores correct mechanical linkage between the motor and driven components
• Matches OEM fit and mounting points to simplify replacement

• One motor assembly kit (single complete motor assembly)

• Turn off power to the appliance at the breaker or unplug before beginning any repair
• Follow OEM disassembly steps to access the motor area; keep fasteners and small parts organized
• Handle electrical connectors carefully; wiring matches diagrams before re-energizing

This support pressure hose connects the refrigerator's pressure-sensing system to the air chamber, helping the dispenser/ice system sense and regulate pressure. Replaces a cracked or collapsed hose to restore proper pressure communication. What it does:

• Channels air pressure from the dispenser/ice housing to the pressure sensor or switch
• Prevents false pressure readings caused by kinks, cracks, or blockage
• Commonly replaced when dispenser or ice maker shows inconsistent operation or error codes related to pressure
• Helps restore reliable dispenser/ice system response when the original hose is damaged

• Refer to the refrigerator service manual for proper routing and secure connection points
• Disconnect power and water supply before beginning service to avoid shock or leaks
• Inspect clamps and nearby fittings; replace damaged clamps or seals as needed

This pressure hose clamp secures the small vacuum/pressure hose to its fitting, keeping the hose in place so the appliance can accurately sense water level and cycle pressure. Simple, direct replacement for a worn or loose clamp. What it does:

• Holds the pressure/vacuum hose snugly to prevent leaks or hose detachment
• Helps maintain proper pressure signal for correct cycle and fill operation
• Commonly used when a loose or damaged clamp causes intermittent pressure-related symptoms
• Small replacement part that restores a firm hose connection

• Disconnect power (and water, if applicable) before servicing the appliance
• Use a small screwdriver or pliers to remove the old clamp and secure the new clamp in place
• Ensure the hose is fully seated on the fitting before tightening the clamp

This heater support stabilizes and secures the heating element assembly to keep the heater properly positioned for safe, efficient operation. Replaces a damaged or broken support to reduce rattling and prevent heater misalignment. What it does:

• Holds the heating element assembly in place so it stays aligned during operation
• Prevents the heater from contacting other components, reducing noise and wear
• Helps maintain proper airflow around the heater for consistent heat output
• Commonly replaced when cracked, warped, or missing mounting tabs

• Disconnect power to the appliance before starting any repair
• Inspect surrounding parts (heater, clips, wires) and replace any damaged items
• Use basic hand tools; handle the heater element carefully to avoid damage

A small sealing ball used in a valve assembly to control fluid flow and maintain a watertight seal. Replaces a worn or damaged valve ball to restore proper sealing and prevent leaks or improper filling. What it does

• Acts as a one-way seal inside a valve or dispenser, allowing flow in the intended direction and blocking backflow.
• Helps stop leaks by seating against a valve seat to create a watertight seal.
• Worn, cracked, or stuck check balls can cause slow or no fill, continuous flow, or leaking from the valve area.
• Functions silently; failure may present as intermittent filling issues or visible leakage.

• One check ball

• Designed to fit inside the valve/dispenser assembly—access requires removing the valve housing or relevant cover.
• Inspect the valve seat and surrounding components for wear or debris; clean before installing the new ball.
• Use manufacturer-recommended tools and follow safety steps: disconnect power and, if applicable, shut off water supply before servicing.

The Inner Door Boot Seal Clamp is an OEM part for GE washing machines. This clamp secures the door boot seal, ensuring it stays in place and forms a watertight barrier between the washer door and drum.  

Causes of a bad clamp can include regular wear and tear, corrosion from detergent and water exposure, or physical damage from rough handling. 

Symptoms of a bad inner door boot seal clamp include:

• Water leaking from the front of the washing machine
• The door boot seal coming loose or not staying in place
• The washing machine door not closing properly
• Visible rust or damage on the clamp

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Outer Door Boot Seal Clamp is an OEM part for GE washing machines. This clamp ensures that the seal is tightly held in place, preventing water from leaking out of the front load washer during operation.  

Causes of a bad Outer Door Boot Seal Clamp can range from corrosion due to exposure to moisture and detergents, to physical damage from improper installation or removal of the door seal.  

Symptoms of a malfunctioning Outer Door Boot Seal Clamp include:

• Water leaking from the front of the washing machine
• The door boot seal coming loose or detaching from the front panel
• Visible damage or corrosion on the clamp, compromising its integrity

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.