Parts for Ge GTW860SPJ1MC: Tub & Motor Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This clamp secures a flexible hose or line to a fitting, helping prevent leaks and keep connections stable during normal appliance operation. A small but essential fastening part for fluid or air lines. What it does:

• Holds a hose or line firmly to a barb, spud, or pipe to maintain a sealed connection
• Helps prevent leaks caused by loose or slipping hoses
• Keeps plumbing or venting lines routed and secure under vibration
• Common replacement when clamps become corroded, cracked, or lose tension

• Inspect mating hose and fitting for damage before installing a new clamp
• Tighten securely but avoid over-tightening, which can cut or deform the hose
• Use appropriate tools (screwdriver or nut driver) and follow appliance safety procedures
• Disconnect power and water supply when working on electrical or plumbing connections

The Impeller is an OEM internal component used in GE washing machine pump and drain assemblies. It circulates water through vanes that spin to transfer liquid within the system.

Symptoms of a bad impeller include: 

• Inability to properly pump or drain water from washer tub
• Pooling, flooding, or residual water left after cycles     
• Grating, squealing, or impaired motorized drain noises

Causes involve cracked, corroded, or out of round vanes reducing hydraulic efficacy over time. Impeller degradation risks flooding.

This GE OEM replacement impeller restores water circulation for efficient draining cycles. Compatible with some Hotpoint and Kenmore models as well, installation maintains optimal liquid transfer capabilities. 

This 1/4-20 2A Sinuloc replacement screw secures panels, brackets and internal components on compatible GE appliances, restoring a tight, vibration-resistant attachment for reliable operation and quieter performance. What it does:

• Secures panels, mounting brackets and other small components to prevent movement.
• Sinuloc (self-locking) design helps resist loosening from vibration or thermal cycling.
• Use when missing, damaged or loose screws cause rattling, misaligned panels or unstable parts.
• Matches the OEM thread form and size for proper fit and engagement.

• Disconnect power and water before accessing the appliance interior.
• Use the correct driver to avoid stripping the head; start threads by hand before tightening.
• Tighten until snug—do not over-torque; replace any additional damaged fasteners.
• Keep small parts secure and follow the appliance manufacturer's service instructions.

The Tub Seal is an OEM part for GE washers. This part seals the washing machine's outer tub, preventing water leakage during the wash cycle.

Causes of a bad Tub Seal can include wear and tear over time, improper installation, or physical damage from foreign objects getting caught in the seal.  

Symptoms of a faulty Tub Seal include:

• Water leaking from the washer during operation
• Excessive moisture or dampness around the washer base
• Mildew or mold growth due to persistent leaks
• Loud sloshing or sloshing noises during the spin cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Spring is an OEM part for GE front-loading washing machines. It is responsible for assisting with the opening and closing of the washer door during the loading and unloading of clothes.

Causes of a bad spring can include cracks or fractures from repeated flexing over thousands of cycles. Stress and damage from excessively heavy loads or forced/slammed door movements can hasten spring failure.

Symptoms of a failed spring include:

• The door being hard to open/close or moving too freely
• An inability to hold the door securely closed
• Unnecessary noise and vibration from the door

Replace the worn spring with this genuine GE OEM part to restore proper function and balance to the door. It is designed for precise performance and durability. This replacement is also compatible with some Kenmore machines using GE components.

A 1/4-20 hex head cap bolt used to secure assemblies and components in compatible appliances. Provides a durable, easy-to-grip head for tightening with a wrench or socket and helps maintain proper alignment. What it does:

• Fastens panels, brackets, and components where a 1/4-20 hex head bolt is required
• Restores secure mounting when a damaged or missing bolt causes loose or rattling parts
• Helps prevent misalignment or movement of assemblies during operation
• Works with standard 1/4-20 threaded holes and mating nuts

• Use the correct socket or wrench size to avoid rounding the hex head
• Tighten to the appliance manufacturer's recommended torque when available; avoid over-tightening
• Replace damaged or corroded bolts with identical thread size and length for safe operation
• Disconnect power and follow appliance safety procedures before servicing

This replacement screw secures appliance components using a 5/16-24 Sinuloc style thread for a vibration-resistant hold. Use it to restore proper fastening and reduce rattling or loose panels caused by worn or missing hardware. What it does:

• Fastens panels, brackets, or assemblies with a 5/16-24 threaded connection
• Sinuloc design helps resist backing out from vibration or thermal cycling
• Restores secure mounting when original screw is stripped, lost, or damaged
• Helps eliminate rattles and movement of attached parts

• Verify correct thread size and engaging part before installation
• Start threads by hand to avoid cross-threading; tighten until secure
• Do not overtighten—use appropriate driver and moderate torque
• Disconnect power and follow appliance-specific safety procedures before servicing

The Platform & Brg Retnr Asm is an OEM replacement part for GE washing machines. It is responsible for supporting and securing the tub while also providing a water-tight seal.

This assembly includes the platform, bearing retainer, and tub seal, all designed to work together to ensure a smooth and efficient washing cycle. The platform and bearing retainer help maintain the stability of the tub, while the tub seal prevents water from leaking out during operation.

Symptoms of a faulty assembly include:

• Excessive noise or vibration during the wash cycle
• Water leaking from the tub area
• Unstable or wobbly tub

A bad platform and bearing retainer or tub seal assembly can be caused by normal wear and tear over time or damage due to heavy loads or unbalanced loads. If you notice excessive noise, leaking water, or a wobbly tub, it may be time to replace this assembly.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed

The Mode Shifter Assembly is an OEM component specifically designed for GE washing machines. It contains the lever and gears necessary to shift the transmission between agitate, spin, and drain functions based on selections made on the control panel. 

Symptoms of a bad mode shifter assembly include:

• Washer fails to switch between cycles properly  
• Repeatedly lands between gears rather than engaging fully
• Grinding noises or difficulty shifting heard from internal mechanisms
• Inability to agitate or spin clothes effectively

Causes can involve worn gears, bent linkage components, or internal issues preventing smooth operation over time. 

This OEM GE replacement part is also compatible with some Hotpoint, RCA, and Kenmore models. 

This rotor position sensor (RPS) module monitors the washer's drive motor position and speed and reports it to the control. Replacing a failing sensor helps restore smooth agitation and dependable spin, reducing stalls and early cycle stops.

• Detects the motor rotor's position/speed so the control can start, reverse, and ramp the motor correctly
• Typical symptoms include no spin or agitation, motor starts then stops, or the cycle ends early
• Causes intermittent/erratic motor movement; lid locks but the tub doesn't move
• Use when diagnostics indicate an RPS/speed-sensor or motor feedback fault

• Disconnect power and turn off water before servicing
• Access the motor area; photograph wiring before disconnecting
• Align the sensor correctly and fully seat the harness connector—do not force pins
• Run applicable diagnostics/calibration after installation to ensure proper spin and agitation

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Hub nut is an OEM part for GE washing machines, designed to securely fasten the tub assembly to the drive system of the washer. This component is crucial for the stability and operation of the washing machine's drum, ensuring that it remains properly aligned and attached during the vigorous motion of the wash cycles.

Per the manufacturer due to the high torgue on the hub nut an impact wrench should be used to remove and replace the hub nut. It also rquires a 90 ft lb torque limiting extension WX05X10028 and a 1 5/16th impact socket WX05X10022. You can order these through the links or use ones you already have. WARNING: The 90 ft lb torque limiting extension must be used when removing or installing the hub nut to prevent damage to the hub nut and transmission due to over torquing with the impact wrench. 

Causes of these issues can range from natural wear and tear over time to improper installation or overloading of the washer, which can exert undue stress on the Nut Hub and other related components. Ensuring that the Nut Hub is in good condition and properly tightened is essential for the longevity and proper function of your GE washing machine.

Symptoms of a faulty Hub nut include:

• Unusual noises during the spin cycle, indicating that the drum may be loose or off-balance
• The washing machine's drum exhibiting excessive movement or vibration beyond normal levels
• Water leaks from the area surrounding the drum

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Washer Hub is an OEM replacement part for GE washing machines. It is a central component located inside the washing machine basket that the inner tub, drive motor, and suspension springs connect to. The washer hub rotates the washing basket during agitation and spinning cycles to clean clothes thoroughly.

Constant rotational motion and vibration placed on the hub can potentially cause cracks or weakness over an extended time. Improper load balancing causing excessive shaking may also damage the hub.

Symptoms of a bad washer hub include: 

• The washing machine basket fails to spin or agitate properly
• Loud grinding or clicking noises coming from inside the machine  
• Vibrations felt through the cabinets or floor during cycles
• Misalignment or wobbling of the inner washing tub

This OEM GE replacement part is compatible with some Hotpoint, RCA, and Kenmore.

This O-ring thermistor is a sealed temperature sensor that restores accurate temperature sensing in refrigeration circuits. It helps the control board read temperatures so the appliance can maintain proper cooling and defrost cycles. What it does:

• Senses temperature at the evaporator/area it's installed in so the control can regulate cooling
• Helps prevent overcooling or undercooling when operating correctly
• Can cause temperature-related error codes or improper defrosting when faulty
• Common symptom of failure: inconsistent temperatures or an error indicating a bad thermistor

• Disconnect power to the appliance before servicing to avoid shock or damage
• Replace with the exact part number to ensure fit and proper operation
• Handle the sensor and O-ring carefully to avoid damaging the lead or seal
• Test continuity/ resistance per the service manual

The Rod & Spring Assembly is an OEM part for GE washers. It contains both the rod and spring components, working in tandem to support and balance the wash basket or tub during agitation cycles. Providing counterbalancing is essential for proper washing performance.

Causes of a bad rod & spring assembly can include fatigue and wear from years of operation, damage or breaks from shifting heavy laundry loads, or corrosion hastened by mineral deposits inside the tub.  

Symptoms include: 

• Excessive vibrating noises 
• The tub or basket no longer agitates properly
• Difficulty moving or spinning freely
• Physical deformation or instability of the tub

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This rotor motor is the rotating motor assembly that spins the appliance rotor to enable proper rotation. It replaces a worn or failed rotor motor to restore normal rotating function and reduce noise. What it does:

• Drives the rotor/turning assembly so the rotor or turntable rotates smoothly
• Replaces a motor that has stopped turning or only hums without spinning
• Can eliminate intermittent rotation or noisy operation caused by a failing rotor motor
• Restores consistent rotation for even operation of the appliance's rotating components

• Disconnect power before beginning any repair to avoid shock or injury
• Remove access panels and mounting screws to access the existing rotor motor
• Note wiring locations or label connectors before disconnecting to ensure correct reassembly
• Test rotation after installation; if issues persist, inspect related parts (mounts, couplings, wiring)

A conical suspension spring that cushions and supports the washer tub to reduce vibration and help stabilize the drum during agitate and spin cycles. Replaces a worn or damaged spring to restore smoother operation. What it does:

• Helps absorb tub movement and shock during spin and agitation
• Reduces excessive vibration and rocking of the washer cabinet
• Can help stop loud banging or thumping noises caused by worn suspension
• Works with the washer's suspension system to keep the tub centered

• One conical suspension spring

• Disconnect power and water before servicing the washer
• Support the tub or cabinet while removing/installing the spring to avoid injury
• Inspect related suspension components and replace as needed
• Follow the manufacturer's diagram and instructions for proper routing and attachment

This hex nut secures threaded studs and fasteners on compatible appliances, providing a reliable metal-to-metal connection that keeps components in place during normal use. Use it to replace a worn or missing nut for a snug, safe fit. What it does:

• Fastens onto a 7/16-20 threaded stud to hold panels, brackets or components together
• Restores proper clamping force where a stripped, corroded or missing nut causes looseness
• Helps stop rattling, movement or misalignment tied to a loose fastener
• Simple hardware replacement that returns original fit and function

• One hex nut (7/16-20 thread, 2B)

• Turn off and unplug the appliance before performing any repair that exposes wiring or moving parts
• Use the correct wrench size and tighten until secure—do not overtighten to avoid damaging studs
• If removing rusted hardware, apply penetrating lubricant and take care not to break studs

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.