Parts for Frigidaire LCE462PL0: 05 - Tubs, Water Valve And Lid Switch Parts

Secure hose clamp for dishwashers. Replace if hoses are loose, leaking, or clamp shows wear or corrosion. Verify fit with your model number before ordering.

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

Replacement mounting screw for washers and laundry centers. Secures panels, components, or brackets. Replace if lost, stripped, or corroded.

Fix leaking or noisy washer drums caused by broken trunnion bolts. This fastener secures the trunnion assembly to prevent water leaks and vibration.

Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.

The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:

• Secures and centers the spin basket on the drive shaft for balanced rotation
• Transfers drive torque to the inner tub during spin
• Helps maintain basket alignment to reduce vibration
• Typical symptoms of failure: loose/wobbly tub, scraping or grinding noises, poor or no spin, frequent out-of-balance events

• 1 trunnion

• Disconnect power and water before service; wear gloves and eye protection
• Access the hub by removing top/access parts, then the agitator/wash plate and inner-tub fasteners
• Clean the shaft and mating surfaces; seat the new trunnion fully and tighten fasteners evenly in a crisscross pattern
• Inspect related parts (tub seal, bolts, bearing) while open and replace if worn; run a short test cycle to ensure smooth spin

Replacement mounting screw for various appliances. Needed when original screws are stripped, lost, or damaged during repair or maintenance work.

Horizontal suspension spring for washer drum support systems. Replaces worn, stretched, or broken springs that cause excessive drum movement or noise.

Suspension spring for washer drum support system. Replaces worn, stretched, or broken springs that cause drum instability or excessive movement.

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.

Rubber washer that seals the connection between your washing machine's inlet hose and faucet. Replace if cracked, worn, or causing leaks at connection.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

A replacement bracket that secures the lid lock assembly to the washer cabinet, restoring proper lid alignment and latch engagement for safe operation. Fits the factory lid-lock hardware to keep the top lid stable during cycles. What it does:

• Holds the lid lock assembly in the correct position so the lid latch can engage reliably
• Prevents the lid from shifting or rattling during spin and agitation
• Helps restore normal start/lock symptoms when a loose or broken bracket prevents the washer from starting
• Works with the existing lid lock and strike to maintain safe operation

• Disconnect power to the washer before beginning any work
• Basic hand tools typically required; follow the washer model's disassembly steps to access the lock area
• Inspect the lid lock and strike for wear and replace if they show damage or prevent proper engagement
• After installation, verify lid closes and the lock engages before running a full cycle

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Sems screw for dryers. Secures internal components and panels. Replace if screw is stripped, missing, or no longer holding parts firmly in place.

Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.

Fix loud whirling noise during spin cycle with this washer spin bearing washer. Supports the belt pulley bearing for smooth rotation. Video available.

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.