Parts for Frigidaire FFRE1533S11: Unit Parts

This replacement air filter screens airborne particles before they enter the appliance. Installing a clean, intact filter helps maintain proper airflow and protect internal components so the unit can operate as designed. What it does:

• Traps dust and lint before they reach the fan and internal parts
• Helps maintain smooth, unobstructed airflow
• A clogged or torn filter can cause weak airflow or unusual noise
• Replace when the filter is missing, damaged, or will not stay seated

• 1 air filter

• Disconnect power before servicing
• Open the filter access or grille and remove the old filter
• Insert the new filter in the same orientation; ensure tabs/slots fully engage
• Do not operate the appliance without a filter installed

This louver is the molded air outlet grille that directs airflow inside the appliance and helps cover the evaporator/vent area for a finished appearance. Replacing a damaged louver restores proper airflow direction and appearance. What it does:

• Directs cooled air from the evaporator into the fresh-food compartment.
• Covers and protects the vent/evaporator opening from debris.
• Helps maintain even airflow; cracked or broken louvers can cause drafts or uneven cooling.
• Restores the interior appearance when the original grille is warped, cracked, or broken.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Access may require removing interior shelves, drawers, or a trim panel.
• Remove clips or retaining screws carefully; do not force the plastic to avoid breakage.
• If clips are damaged during removal, replace them to ensure a secure fit.

This louver is the replacement air vent grille that directs airflow inside the appliance to help maintain even cooling and protect internal components from debris. Restores proper airflow and helps reduce unusual noises from broken or loose vents. What it does

• Directs and channels airflow over the evaporator and compartments for consistent temperature distribution
• Covers and protects internal openings from large debris and objects
• Replaces cracked, broken, or missing louvers that can rattle, vibrate, or allow uneven cooling
• Matches OEM fit to align with existing mounting points and airflow paths

• Disconnect power before starting any repair to avoid electrical shock
• Remove shelves, panels, or trim as needed to access the louver; keep fasteners for reuse unless replacement specified
• Inspect surrounding seals and mounting clips; replace damaged clips to ensure a secure fit

This louver is the replacement vent trim that covers and directs airflow while protecting internal components from debris. It restores appearance and proper airflow control for the appliance's vent opening. What it does:

• Covers the appliance vent opening and helps channel airflow
• Protects internal components from dust, debris and direct exposure
• Restores damaged or cracked vent trim for a finished look
• Can reduce draft and prevent items from contacting internal parts

• One replacement louver

• Disconnect power (or unplug) before starting any repair
• Remove any screws or clips holding the old louver; retain fasteners if reusing
• Align the replacement louver and secure with original fasteners without over-tightening

This electronic control board manages the oven's functions and user inputs, providing reliable timing and power signals to heating elements and displays. Replacing a faulty board restores proper control and cycle operation. What it does:

• Regulates oven timing, temperature commands, and cook cycles
• Processes user inputs from the touchpad or knobs and controls the display
• Sends power signals to heating elements, relays, and safety circuits
• Common symptom sources: unresponsive controls, incorrect cycles, error codes, or no heat

• Disconnect power at the breaker before starting any repair
• Handle the board by its edges and avoid touching contacts or components
• Verify the part number on the existing board matches before installing

This handheld remote control lets you operate compatible Frigidaire appliances from a distance, restoring convenient control of modes, temperatures, and timers without touching the main unit. What it does:

• Sends remote commands to the appliance so you can change modes, fan speed, temperature, or timers from across the room
• Replaces a lost, cracked, or unresponsive remote to regain full remote functionality
• Helps when the appliance doesn't respond to the existing remote or when buttons stick or fail
• Uses standard battery power

• One handheld remote control

• Insert fresh batteries and aim the remote at the appliance's IR receiver; check batteries first when troubleshooting
• Re-pairing or simple setup may be required per the appliance owner's manual—follow OEM instructions if prompted
• Keep remote dry and avoid dropping; remove batteries if storing long-term
• Recycle or dispose of old batteries and electronics according to local regulations

This replacement power cord restores AC power to compatible refrigerators by replacing a damaged or worn supply lead. It provides a direct, safe power connection so the appliance can run reliably. What it does:

• Replaces a frayed, cut, or otherwise damaged power supply cord
• Restores consistent power when the appliance will not turn on or has intermittent power
• Maintains the appliance's grounding connection for safe operation
• Prevents electrical arcing from exposed wiring or compromised insulation

• One replacement power cord

• Disconnect the appliance from the power source before inspecting or replacing the cord
• Install with the proper strain relief and secure fasteners to prevent pinching or pull-out

This electronic control board replaces the oven/range control assembly that manages cooktop and oven functions, restoring reliable control and display operation. It helps stop erratic cycles and restores normal user-interface responsiveness. What it does:

• Controls oven and cooktop cycles, temperature sensing inputs, timers and display functions
• Replaces a failed control that causes no display, unresponsive touchpad/buttons, or inability to start heating
• Regulates relays and signals to burners and bake/broil elements for proper operation
• Works with the appliance's wiring harness and sensors to restore normal electronic control

• One electronic control board (assembly) as pictured

• Disconnect power at the breaker or unplug the appliance before servicing to avoid shock
• Handle the board by the edges and avoid electrostatic discharge; use an ESD strap if available
• Verify connectors and wire harness orientation before removal; take photos to aid reassembly

This temperature sensor (thermistor) monitors fresh food/freezer temperatures and sends readings to the refrigerator control board so the appliance maintains consistent cooling. Replaces a failed or intermittent sensor to restore accurate temperature control. What it does:

• Senses interior temperature and reports it to the control board
• Helps the compressor, fans and defrost system run at the correct times
• Common symptom: fridge or freezer temperatures are too warm or fluctuate
• Common symptom: unit runs constantly or cycles erratically
• Common symptom: inconsistent cooling between compartments

• One temperature sensor (thermistor)

• Disconnect power to the appliance before attempting any repairs
• Handle the sensor and wiring gently; avoid kinking or stretching the lead
• Verify connector pins align and seat fully; some models use a simple plug-in connector

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

A replacement motor start/run capacitor that helps the refrigerator's compressor and fan motors start and run more reliably. Restores proper motor operation when the original capacitor has failed or weakened. What it does:

• Provides the boost of electrical charge motors need to start and maintain proper running speed
• Commonly linked to symptoms such as a humming compressor, motors that won't start, or intermittent cooling
• Helps stabilize motor performance and reduce hard-starting that can strain components
• Used in refrigeration motor circuits that require a start/run capacitor

• One motor start/run capacitor

• Disconnect power to the appliance before beginning any service
• Capacitors can hold a charge—discharge safely
• Inspect mounting and wiring; replace using the same terminal connections and secure mounting

This blower wheel circulates air through the dryer to maintain proper airflow for efficient drying and venting. Replacing a worn or damaged wheel restores air movement so the dryer can dry clothes and vent heat correctly. What it does:

• Spins with the motor to pull air from the drum through the heating assembly and out the vent.
• Restores normal airflow when worn, cracked, or missing fins reduce performance.
• Can resolve symptoms like weak airflow, long dry times, or overheating caused by restricted circulation.
• Works with the dryer's motor and housing to keep exhaust flow consistent.

• One blower wheel

• Disconnect power (and gas if applicable) before servicing.
• Access typically requires removing the dryer front or rear panel and drum; follow your model's service instructions.
• Inspect motor shaft and mounting hardware; replace any damaged fasteners or clips as needed.

This replacement blade fan moves cold air across the evaporator to help maintain even temperatures inside the compartment. It restores proper airflow for more consistent cooling and helps reduce frost buildup when working with a good motor. What it does:

• Circulates air across the evaporator to distribute cold air through the compartment
• Restores airflow when a cracked, warped, or missing blade reduces cooling efficiency
• Helps reduce uneven temperatures and localized warm spots caused by poor airflow
• Can reduce abnormal noises caused by damaged or unbalanced blades

• One replacement blade fan

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover/panel to access the fan assembly per your model's service instructions
• Handle the replacement blade carefully to avoid bending the blades or contaminating the evaporator
• If the fan motor or mounting hardware is damaged, replace those parts as well for reliable operation

This screw kit is a replacement hardware pack used to restore secure fastening of appliance panels and components. It provides the standard mounting screws needed when original fasteners are missing, damaged, or worn. What it does:

• Replaces missing or stripped screws that hold panels, trim, or small assemblies in place
• Restores secure fit to reduce rattling, vibration, or loose parts
• Helps correct minor alignment issues caused by lost fasteners
• Useful when preparing for panel removal/reinstallation during service

• Disconnect power to the appliance before servicing.
• Use the correct screwdriver or driver bit to avoid stripping screw heads.
• Tighten screws until snug; avoid overtightening to prevent damage.
• Follow OEM service instructions.

This window filler kit replaces the trim piece that surrounds an appliance viewing window to restore a finished appearance and help block gaps where dirt and drafts can enter. It's a direct-replacement trim designed to match the OEM fit. What it does

• Restores the finished edge around the appliance window for a clean, factory look
• Covers gaps between the window and surrounding trim to help reduce debris and drafts
• Replaces cracked, bent, or missing window filler trim that affects appearance or sealing
• Works with the original window assembly and mounting points for a straightforward fit

• One window filler kit (single trim assembly)

• Disconnect power to the appliance before attempting any repair; work on cool surfaces
• Remove any fasteners or clips securing the old filler; handle glass and painted surfaces carefully
• Use basic hand tools; align the new filler with existing holes and secure per manufacturer guidance