Parts for Jenn-Air JBRFL24IGX10: Upper Unit Parts

This outer trim cover protects internal components and finishes the appliance's exterior while keeping wiring and controls out of sight. It restores a clean look and helps prevent contact with moving or electrical parts. What it does:

• Covers and protects internal components behind the control area or access opening
• Prevents dirt, debris and accidental contact with wiring or switches
• Stops drafts and reduces noise from internal components
• Commonly replaced when cracked, broken, warped or cosmetically damaged

• Disconnect power to the appliance before attempting any service
• Handle carefully to avoid scratching the finish or cracking plastic tabs
• Use only manufacturer-recommended fasteners; do not force tabs or hinges

This replacement filter cap secures the refrigerator water/air filter housing and helps maintain a tight seal to prevent leaks and ensure proper filter alignment. Fits as the direct replacement part number W11679634. What it does:

• Seals the filter housing to help prevent water or air leaks
• Keeps the filter properly seated for reliable operation
• Restores the original mounting/retention function when a cap is cracked or missing
• Helps maintain normal water/ice dispensing and filtration performance when filter is correctly installed

• One filter cap (part W11679634)

• Disconnect power and shut off the water supply before beginning any repair
• Remove the old cap by following the OEM instructions for your model; installation typically involves aligning and snapping or fastening the cap into place
• Inspect the filter housing and O-rings for damage and replace if necessary to ensure a proper seal

The Whirlpool EveryDrop Ice and Water Refrigerator Filter 2 is an OEM replacement part for Whirlpool refrigerators. This advanced water filter is designed to provide superior filtration for both the ice maker and water dispenser. This water filter effectively reduces numerous contaminants, including lead, pesticides, and pharmaceuticals, ensuring that your drinking water and ice are not only clean but also taste great.  

Regular replacement of the EveryDrop Filter is recommended to maintain optimal performance and water quality. Over time, filters can become clogged with particles and contaminants, leading to reduced water flow and a decline in the effectiveness of filtration.

Symptoms of a filter that needs to be replaced include:

• Noticeable decrease in water flow rate from the dispenser
• Unpleasant taste or odor in the water and ice
• The filter indicator light on the refrigerator turns on

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This refrigerator water filter housing holds the filter and routes water through it to the dispenser and ice maker. Replace it if the housing is cracked, leaking, or won't engage the filter to help restore consistent water flow. What it does:

• Directs household water through the installed filter to the dispenser and ice maker
• Locks and seals the filter; opens/closes the internal shutoff when the filter is engaged
• Helps maintain proper flow and reduce leaks at the filter connection
• Common failure symptoms may include water dripping from the filter area, the filter not seating or popping out, low/no dispenser flow, or no ice production

• 1 water filter housing assembly

• Unplug the refrigerator and shut off the water supply; dispense water to relieve pressure
• Place a towel under the area to catch residual water
• Remove any cover/bracket as needed; disconnect tubing from quick-connect fittings and note routing/orientation
• Install the new housing, fully seat tubing in the fittings, restore water and power, check for leaks, and flush per your model's instructions

This water inlet valve controls the flow of water into the appliance so it fills when needed and stops when full, restoring proper water delivery for cycles and ice/water features. Designed as a direct-fit replacement. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Prevents overfilling by shutting off water when the cycle completes
• Common symptom: appliance won't fill or fills slowly
• Common symptom: continuous water flow or valve leaking at the connection

• Disconnect power and shut off the water supply before starting work
• Use basic hand tools; support water lines and replace any worn inlet gaskets or seals
• Inspect fittings for damage and tighten connections to prevent leaks
• Test multiple cycles after installation to ensure proper operation

The Power Control Board is an OEM component for Whirlpool refrigerators. It is an essential electronic component responsible for monitoring and regulating power distribution throughout the entire unit. The power control board controls components such as cooling fans, compressors, lights, ice makers, and more.

Symptoms of a bad power control board include: 

• Lights, fans, or other components failing to turn on
• Inability to adjust temperature settings  
• Constant tripping of circuit breakers
• Error codes displayed that cannot be cleared

Causes of failure include moisture damage, component breakdown over time, or power surges that can fry circuitry.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

This electronic control board replaces the appliance's main control module to restore proper operation of timed cycles, displays and user commands. It provides the control logic that manages the unit's functions and user interface. What it does:

• Manages and sequences appliance functions such as cycle selection, timing and accessory control
• Powers and communicates with the display and touch/selector controls
• Interprets user inputs and triggers valves, motors and other components
• Faulty boards can cause unresponsive controls, incorrect cycles, intermittent operation, or display error codes

• Disconnect power to the appliance before starting any repair to avoid electrical shock
• Handle the board by the edges and avoid static discharge—use an anti-static wrist strap if available
• Verify connector orientation and secure all wiring; do not force connectors

This electronic control board replaces the oven's main control to manage cooking cycles, display, and user inputs for reliable operation. Restores control functions so the appliance responds correctly to settings and timers. What it does:

• Interprets touchpad/keypad or front-panel commands and runs oven cycles
• Controls bake/ broil elements, timing, and display functions
• Works with the appliance's wiring harness and sensors to coordinate oven operations

• One electronic control board

• Always disconnect power at the breaker before starting any repair
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Replace by removing the console/back panel and swapping the board and connectors exactly as removed