Parts for Maytag MLE22PRAYW0: Washer Cabinet Parts

Front toe panel that covers the washer's lower base. Replaces cracked, dented, or missing kick plate to restore finished appearance and protect components.

Threads into the washer base to adjust height and stabilize the unit. Replace if cracked, stripped, or missing to eliminate rocking on uneven floors.

Fix washer shaking and excessive vibration during spin cycles. This leveling leg locking nut secures adjustable legs to stabilize your machine.

Strain relief cable for washers. Secures and protects electrical wiring at connection points. Replace if cracked, damaged, or missing to maintain safe wire management.

Secures panels, trim, or small components on dryers to restore proper fit and reduce noise. Replaces worn, loose, or missing fasteners for firm assembly.

This replacement console panel restores the appliance's front housing for the control area, protecting internal components and keeping buttons and displays aligned for reliable operation and a clean appearance. What it does:

• Replaces a cracked, scratched or broken console housing to improve appearance and protect controls
• Provides the mounting surface and alignment for the control board, buttons, and display
• Prevents dust and moisture from reaching internal electronics through the console opening
• Helps restore proper fit and function when the original panel is warped or damaged

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Installation typically requires removing trim pieces and screws; handle the panel carefully to avoid scratching.
• Support the control assembly while removing and reconnecting any wiring harnesses; do not force connectors.

Mounting bracket for laundry center installations. Provides structural support for secure appliance positioning. Replace if bent, cracked, or missing.

Shipping bolt kit secures washer drum during transport. Includes 4 bolts to prevent drum damage when moving. Replace if lost or install before relocating.

Washer won't start, agitate, or spin? This motor control board regulates drive motor speed and direction. Restores proper wash and spin cycles.

Secures washer hoses and prevents leaks by maintaining consistent pressure. Replace if you notice water leaks or loose connections. Verify fit with your model.

Fix washer leaks during drain cycle with this drain hose connector. Replaces broken or damaged connectors causing water leaks. Easy 15-minute DIY repair.

Grey rubber bumper for washers. Replaces worn, cracked, or missing bumpers that cushion the drum or cabinet. Installs on various washer models.

8-18 x 1/2 inch mounting screw for refrigerators, washers, dryers, and other appliances. Replace stripped, missing, or damaged screws during repairs.

Washer won't start or trips breaker? This RFI noise filter conditions AC power and protects control circuits. Easy DIY fix with video guide included.

Fix F03 E01 or F08 E01 error codes with a new water level pressure switch. Controls fill and drain cycles. Easy 5-minute DIY replacement for washers.

Replacement water hose for washers. Restores leak-free water flow between internal components. Replace if leaking or causing error codes. Verify fit.

Replacement mounting screw for securing panels and internal components in your dryer. Needed when original hardware is missing, stripped, or damaged.

Transport cover bracket that secures washer components during shipping and service. Replace if cracked, broken, or missing to prevent damage during moves.

Secures your washer's drain U-bend to prevent leaks and keep plumbing properly aligned. Simple push-fit installation takes just minutes to complete.

Washer won't start or shows electrical faults? A failed ground switch disrupts the safety circuit. This switch restores proper grounding for reliable operation.

Rubber grommet for washers. Installs to cushion components, seal openings, or protect wiring. Replace if cracked, torn, worn, or missing.

Replacement screw for dryer assembly. Used to secure panels, components, or internal parts. Needed when original screw is stripped, lost, or broken.

Wire tie secures and organizes internal wiring harnesses in your appliance. Replace if the original tie is broken, cracked, or missing during repairs.

Guide sleeve for washer drum or agitator assembly. Replaces worn, cracked, or missing sleeves that cause misalignment or rattling during operation.

Secures wiring bundles inside your microwave. Replace this wire tie if it's cracked, broken, or missing to keep internal wires organized and secure.

Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.

Replace your dryer door seal to prevent heat loss and improve drying efficiency. Install when you notice air leaks or torn rubber around the door opening.

Wire harness for laundry center electrical connections. Replaces damaged, frayed, or corroded wiring harness. Restores proper power distribution.

Mounting bracket for laundry center units. Secures components in proper position. Replace if cracked, bent, broken, or missing during installation.

Secures pedestal panels, brackets, and trim pieces. Replaces missing, stripped, or damaged screws to restore proper alignment and eliminate rattling.

Stacking bracket for securing a dryer on top of a compatible washer. Replace if bracket is cracked, broken, or missing to safely stack your laundry units.

Fix no power or control issues in your laundry center with this transformer. Compatible with washer-dryer combos. Moderate DIY repair, 1-2 hours.

This wire harness assembly routes power and signals between components so your appliance's electrical circuits connect reliably. Replaces a worn or damaged harness to restore proper electrical continuity and reduce intermittent failures. What it does:

• Carries power and control signals between control board, sensors, and other components
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or component failures
• Helps restore proper electrical connections that may eliminate error codes or non-responsive functions
• Designed to match OEM connector types and lengths for correct fit and function

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Compare harness and connector shapes to the original before installing; route wires per OEM routing to avoid heat or pinch points.
• Use proper wire connectors and secure harness with the existing clips or ties; avoid stretching or kinked wires.
• Test appliance functions after installation.

This electrical wire harness routes power and control signals between internal components to restore reliable connections and proper operation. Replaces a worn or damaged harness to stop intermittent faults and lost functions. What it does:

• Routes power and signal wiring between control and internal components to maintain circuit continuity.
• Replaces frayed, melted or broken wiring that can cause intermittent operation or complete failure.
• Helps resolve symptoms such as the appliance not starting, certain functions not responding, or intermittent power to motors, lights or controls.
• Restores secure plug-and-socket connections that may have corroded or loosened over time.

• One complete wire harness assembly as shown.

• Disconnect power (unplug or shut off breaker) before beginning any repair.
• Inspect connector orientation and wire routing; install using existing clips and strain-relief points to prevent chafing.
• Handle connectors carefully — align pins before seating to avoid bent terminals.

Fix intermittent power issues or complete component failures in your laundry center. This control wire harness restores electrical connections between parts.