Parts for Bosch WFR2460 UC/01 (FD 8201-): 02 - Frame & Door Assemblies Parts

This small plastic push-on cap covers and protects exposed shafts or fasteners to restore a finished appearance and prevent debris buildup. Fits specific Bosch appliance locations where a cosmetic protective cover is required. What it does:

• Covers exposed shafts, posts, or screw heads to prevent dirt and snagging
• Restores the appliance's finished look after part replacement or repair
• Helps keep moisture and debris out of small openings around mounting points
• Simple, non-mechanical part—no electrical or moving components

• Push the cap onto the matching shaft, post, or fastener until it seats firmly
• Use gentle pressure to avoid deforming the cap; do not force onto mismatched sizes
• Disconnect power to the appliance before accessing internal panels or fastener areas
• Replace only with the correct cap size for the specific location to ensure a secure fit

Side. 1 included. Front load

Top. 1 included. Front load

2 included - Front load

This replacement foot supports and levels your appliance so it sits steady and operates smoothly. Replace a worn or missing foot to restore proper height, reduce wobble, and help protect surrounding surfaces.

• Supports the base/frame to maintain proper height and alignment
• Provides leveling adjustment so the unit remains stable
• Helps reduce rocking, vibration, and rattling during operation
• Replace if the original foot is cracked, stripped, missing, or won't adjust

• Disconnect power; shut off water or gas supplies if applicable
• Carefully tilt or raise the unit to access the foot location
• Remove the damaged foot and install the new one per design
• Level the appliance front-to-back and side-to-side; verify stability before use

A front lower trim piece that finishes the base of the washer and helps protect the cabinet opening from debris. Replaces a cracked, dented or missing toe kick to restore a clean appearance and proper fit at the washer's base. What it does

• Covers and protects the washer's lower front opening from dust and small debris.
• Restores the factory appearance when the original toe kick is damaged or missing.
• Helps reduce visible gaps that can catch lint or small items.
• Stops rattling or loose fit at the base when the original piece is bent or broken.

• One front lower toe kick panel (single piece as shown)

• Disconnect power and water before doing any service that requires removing panels.
• Access typically requires removal of the lower access panel or front service panel—keep small fasteners in a secure place.
• Handle edges carefully to avoid cuts; use gloves if needed.

A front lower trim piece that finishes the base of the washer and helps protect the cabinet opening from debris. Replaces a cracked, dented or missing toe kick to restore a clean appearance and proper fit at the washer's base. What it does

• Covers and protects the washer's lower front opening from dust and small debris.
• Restores the factory appearance when the original toe kick is damaged or missing.
• Helps reduce visible gaps that can catch lint or small items.
• Stops rattling or loose fit at the base when the original piece is bent or broken.

• One front lower toe kick panel (single piece as shown)

• Disconnect power and water before doing any service that requires removing panels.
• Access typically requires removal of the lower access panel or front service panel—keep small fasteners in a secure place.
• Handle edges carefully to avoid cuts; use gloves if needed.

The Door Latch is an OEM part for Bosch washing machines. This latch securely fastens the washer door shut during operation.

Causes of a bad door latch can include wear and loosening of moving components from repeated use, or damage from forced door openings.

Symptoms of a bad door latch include:

• The door popping or releasing unexpectedly during a cycle
• Difficulty fully closing and latching the door
• Water leaks due to poor door sealing

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This door hinge bushing sits between the hinge and pivot point to reduce friction and wear. Replacing a worn bushing restores smooth, quiet door movement and helps keep the door properly aligned over time. What it does:

• Provides a smooth, low-friction pivot surface for the hinge
• Helps maintain door alignment and consistent opening/closing feel
• Reduces squeaks, grinding, or binding from the hinge area
• Replaces cracked, flattened, or missing bushing that can make the door feel loose or stiff

• 1 door hinge bushing

• Disconnect power to the appliance before servicing
• Support the door to relieve hinge tension; hinges may be spring-loaded—control door movement
• Access the hinge per your model's service information and note the bushing's orientation
• Install the new bushing, reassemble, and test door travel and latching

Restore smooth, secure door movement with this door hinge. It supports and guides the door through opening and closing, helping ensure proper alignment and consistent sealing so the appliance operates safely and efficiently.

• Supports the door's weight and pivots for smooth opening/closing
• Helps maintain correct door alignment and gasket contact
• Wear or damage can cause sagging, misalignment, noisy operation, or incomplete closing
• Replacing a worn hinge can improve door seal and overall performance

• Disconnect power and allow the appliance to cool before service
• Support the door during removal to prevent strain on the remaining hinge
• Transfer any original fasteners to the new hinge if re-used
• Check door alignment and operation before restoring power

The Fastening Ring is an OEM part for Bosch front load washers. It secures the door boot seal to the front panel of the washer, ensuring a tight and leak-free connection. This ring is essential for maintaining the washer's seal during operation, preventing water from escaping the drum.

Causes of a bad fastening ring can include normal wear and tear, rust or corrosion, and damage from over-tightening or mishandling during maintenance.

Symptoms of a bad fastening ring include:

• Water leaking from the door area
• The door boot seal becoming loose or detached
• Visible damage or deformation of the ring

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This window frame is the replacement trim piece that surrounds and secures the door glass, restoring the door's finished appearance and helping maintain a proper seal. Use it to repair damaged or loose door trim. What it does:

• Secures and frames the door glass so the door looks and fits correctly
• Helps keep the glass properly positioned to maintain a tight fit
• Replaces cracked, warped, or cosmetically damaged trim
• Can reduce air gaps and rattling caused by a loose or broken frame

• Intended for experienced DIYers;
• Power off and disconnect the appliance before beginning any door disassembly
• Handle glass and trim carefully to avoid damage or personal injury; wear gloves and eye protection
• Use only the specific replacement frame for your model to ensure correct fit

This latch secures the appliance door closed and lets the control know when it's safe to run a cycle. Replacing a worn or damaged latch restores reliable door closure and consistent cycle starts.

• Engages the door strike to hold the door shut during operation
• May include an internal switch that signals door-closed status to the control
• Helps prevent cycle interruptions caused by a door-ajar condition
• Common symptoms: door won't latch, door pops open, cycle won't start, "door open" message or beeping

• Disconnect electrical power before servicing; shut off water supply if applicable
• Access and fasteners vary by model; latch mounts at the door/front panel area
• Transfer any mounting hardware and connectors from the original part one-for-one
• After installation, verify proper alignment with the door strike and that the unit recognizes "door closed"

Door handle pin secures the appliance door handle to the door assembly, restoring a firm, stable grip and preventing the handle from slipping or detaching. What it does:

• Acts as the pivot/fastening pin that holds the door handle to the door or door trim.
• Replaces worn, bent, or broken pins that cause loose, wobbly, or sagging handles.
• Helps prevent the handle from falling off or catching when opening and closing the door.
• Restores proper alignment and reliable leverage for normal door operation.

• Disconnect power to the appliance before starting any work; for water-connected appliances also turn off water supply.
• Remove the handle and any trim carefully to access the pin; keep small fasteners in a safe place.
• Install the pin in the same orientation as the original; if retaining clips or bushings were present, reuse or replace them as needed.
• If you encounter springs, clips, or hidden fasteners, proceed cautiously.

Replacement dishwasher door handle that restores a secure grip and proper door operation on compatible Bosch dishwashers. Restores function and appearance so the door opens and closes smoothly and safely. What it does:

• Replaces a cracked, broken, or missing door handle to restore safe opening and closing.
• Secures to the dishwasher door so the latch and seal operate without interference from a loose or damaged grip.
• Reduces wobble and prevents slipping when pulling the door open.
• Helps avoid accidental drops or damage caused by a compromised handle.

• Disconnect power to the appliance before starting; for dishwashers also turn off the water supply if panels or connections will be removed.
• Support the door while removing and installing the handle to prevent it from dropping or bending.
• Basic hand tools (screwdriver, possibly socket) are typically required; retain any original screws or clips unless the new part includes replacements.
• Follow OEM disassembly steps for inner door panels if the handle attaches from inside the door.