Parts for Maytag MDB7751AWQ: 06 - Tub Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Specs: 10-32X.400 (T-20 HEAD)

8-16 x 3/8 inch screw fastener for dryers. Secures baffles to drum and various internal components. Replace if missing, stripped, or damaged.

Fix a dishwasher not filling with water or filling too slowly. This inlet valve controls water flow into your dishwasher. DIY repair with video guide.

Secures water and drain hoses in washers to prevent leaks. Replace if connections loosen or clamp shows corrosion. Confirm fit with your model number.

Fix water leaking from your dishwasher with a new injector hose. This flexible hose connects the dispenser to the pump, restoring proper water flow. DIY-friendly repair.

Seals the air/water inlet where it meets the tub to prevent leaks. Replace if you notice water dripping during cycles. Confirm fit with your model.

Water deflector for dishwashers. Directs spray during wash cycles. Replace if cracked, broken, or missing to restore proper water distribution.

Left hand side

Specs: 10-32X.400 (T-20 HEAD)

Replace your dishwasher's left corner trim to restore the door edge finish and protect the gasket area. Verify fit with your model number before ordering.

Replace your dishwasher door seal to stop leaks and restore proper moisture containment. Fits into the tub channel for a watertight barrier. Confirm fit.

Secures your dishwasher to surrounding cabinetry. Replace this bracket if it's bent, broken, or missing to restore a tight, level installation.

Color: Bisque.

Color: Bisque

Insulates your dishwasher tub to reduce noise and maintain temperature. Replace if worn, damaged by pests, or causing odors. Confirm fit with your model.

Replace your dishwasher's spring adjustment bracket if cracked, bent, or missing. This structural component secures the spring mechanism inside your unit.

Specs: 10-32X.400 (T-20 HEAD)

This dishwasher door spring provides the counterbalance tension that lets the door open and close smoothly. Replacing a worn or broken spring restores proper door feel and helps prevent the door from dropping unexpectedly.

• Provides counterbalance tension so the door opens and closes smoothly
• Helps the door stay partially open without drifting
• Reduces slamming or sudden drop when opening
• Common failure signs: door feels heavy, drops quickly, opens unevenly, or a spring is visibly broken

• Disconnect power and shut off water; remove the toe-kick/access panel
• Support the door; note spring routing and which frame holes are used before removal
• Install the new spring in the same holes; adjust hole selection only per service information to fine-tune tension
• Springs are under tension—wear gloves/eye protection; consider replacing both springs together for balanced operation

Connects dishwasher door to tension springs for balanced opening and closing. Replace if cable is broken, frayed, or detached from mounting points.

Color: White

Specs: 10-32X.400 (T-20 HEAD)

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.

Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.

Right hand side. For left hand use WPW10117485

Left hand side. For right hand use W10117484

Specs: 10-32X.400 (T-20 HEAD)

Specs: 10-32X.400 (T-20 HEAD)

8-16 x 3/8 inch screw fastener for dryers. Secures baffles to drum and various internal components. Replace if missing, stripped, or damaged.

Kit includes more than shown on picture. New kit is for both plastic and stainless tubs. Plastic tubs use only the float and the switch stainless tubs use all the parts.

Dishwasher standpipe installs in the tub assembly to route water during drain cycles. Replace if cracked, broken, or leaking at base or connections.

Replace your dishwasher's float assembly if it's cracked, broken, or missing. This component installs in the tub bottom to monitor water levels during cycles.

Kit includes more than shown on picture. New kit is for both plastic and stainless tubs. Plastic tubs use only the float and the switch stainless tubs use all the parts.

Trim piece that finishes the lower edge of the dishwasher tub opening. Replace if cracked, warped, or missing to restore a clean edge and smooth door operation.

Fixes dishes not drying or water staying cold. This heating element warms wash water and aids drying. Requires pulling unit out. 30-60 min install.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.