Parts for White Outdoor 252-586-190 / 1992: Blower Housing Parts

This upper discharge chute is a genuine MTD part, sold individually. This upper discharge chute can be used as a replacement part in a snowblower or an edger. The purpose of the upper discharge chute is to provide a channel through which the snow or greenery can be gathered and then dispelled by the equipment. The upper discharge chute in a snowblower or an edger might need to be replaced at some point within the typical lifespan of the appliance. This could occur if the upper discharge chute is punctured dented, cracked, eroded, or warped. If this occurs, the upper discharge chute should be removed and replaced by this genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This upper discharge chute is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Montgomery Wards, Yard Man, and MasterCut.

This carriage bolt is a fastener with a flat tip and a round head with threading along the shank. Also known as coach bolts and plow bolts, the item can be used with many types of lawn and garden equipment. This is a 5/16 carriage bolt that resists turning after the bolt has been tightened. Wear and tear or impact can cause damage to a carriage bolt and lead to the need to replace them.Removing a carriage bolt requires twisting the nut loose from the end of the bolt and then hitting the nut with a hammer. This will begin to move the shoulder out of the lawn equipment. Continue the process until the bolt is loose enough to remove. Installing a new carriage bolt simply requires sliding the bolt into the hole, adding the nut, and tightening things up.This carriage bolt is designed for use with Craftsman, MasterCut, Toro, Yard-Man, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines lawn and garden equipment. It can be used with lawnmowers, chainsaws, snowblowers, edgers, and tillers. This is a genuine OEM product sourced directly from the manufacturer as an individual component.

This part is a replacement screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken, stripped, or misplaced screw in a variety of small engine outdoor power equipment models. This screw is a standard piece of hardware that has multiple different uses depending on the equipment in question. In general, screws are used to hold together parts the equipment securely. A genuine OEM screw should be used in order to ensure good quality and a proper fit. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referenced. As an authentic replacement part, this screw is suitable for use on several different models of small engine outdoor power equipment manufactured by MTD, Troy-Bilt, Craftsman, and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.

This lower chute is a genuine MTD part. It is manufactured as a replacement part for snowblowers and edgers. The lower chute helps guide snow (on a snowblower) or debris (on an edger) away from both the engine and user. Especially on a snowblower, if the lower chute is not working properly, the equipment can not perform its job properly. Since the chute is used heavily and is located on the outside of the machine, it is prone to damage. Replacing it does not require disassembling the engine, though proper safety precautions--such as disconnecting the spark plug, emptying the fuel tank, and completely cooling the engine--should be taken. In addition, wear protective gloves to protect from the blades of the machine.This lower chute is a genuine OEM part and is sourced directly from the manufacturer. It is sold individually. It is compatible with equipment made by Craftsman, Cub Cadet, MTD, Yard Machines, Montgomery Ward, MasterCut, and White Outdoor.

A carriage bolt is a type of fastener. It features a smooth rounded head and a square domed top. It has threading, which leads to up to the square shoulder. The purpose of its square is to prevent the bolt from spinning. Once the carriage bolt is inserted through the hole, using a nut and washer can provide additional security. Carriage bolts can corrode and loosen over time. Since it doesn't have a slotted head, a socket wrench is needed when replacing. This bolt carriage replacement is compatible with wood chippers, tillers, string trimmers, lawnmowers, and edgers. It is a genuine MTD product that measures 5/16x.075. It has a smooth rounded head and square shoulder underneath it. This carriage bolt is sold individually.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This flat washer is a genuine MTD part, sold individually. This flat washer can be used as a replacement part in a variety of small engine outdoor appliances including lawn mowers, snowblowers, tillers, string trimmers, chainsaws, edgers, log splitters, and wood chippers. The purpose of the flat washer for one of these small engine outdoor appliances is to serve as a fastening component within the internal mechanisms of the appliance so that friction is reduced and components are spaced apart from one another.The flat washer is a small component that can be easily misplaced or lost within the lifespan of a small engine outdoor appliance; additionally, the flat washer can be subject to stripping away and wearing out over time from general use. If this occurs, the flat washer should be replaced by this genuine OEM replacement part.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This flat washer is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Broan, Yard Machines, Huskee, Montgomery Wards, Yard-Man, Turf King, and MasterCut.

This ball bearing assembly has a wide variety of uses in a number of gasoline-powered yard tools. Bearings are used to provide smooth, friction-free motion between the rotating parts of equipment where pieces fit together and move. The weight and momentum of the rotating motion are distributed to the ball bearings, which prevents wear on the equipment and allows smooth, repetitive motion. Ball bearings are used in equipment such as tillers and lawn tractors, as well as other power equipment that is self-propelled. The bearings will wear out over time since they are on the receiving end of all the angular momentum of the equipment being used. One of the chief locations where bearing assemblies need to be replaced are the drive wheels of the riding mowers and lawn tractors. The bearings are located in brass housings specifically machined to hold them. Since it can be difficult to remove the old ball bearing assemblies from these housings, it is worth considering simply replacing the entire housing as well as the bearing. These bearings are genuine OEM manufactured replacement parts. They are compatible with MTD, Yard-Man, Troy-Bilt, Husky, Cub Cadet, and Yard Machine lawn tools.

This drive pulley is a genuine MTD part, sold individually. This drive pulley can be used as a replacement part in a snowblower or an edger. This part is used in conjunction with the drive belt to move the appliance.The drive pulley in a snowblower or an edger might have to be ordered as a complete replacement part in a drive pulley that can no longer generate rotation in the wheels of the appliance. This could occur if the drive pulley has suffered damage from general wear and tear with long-term use or as the result of a collision with a hard object such as a rock or a curb.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This drive pulley is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Montgomery Wards, Yard Man, and MasterCut.

This key is a genuine MTD part, sold individually. A key can be used as a replacement part for outdoor appliances including lawn mowers, snowblowers, tillers, and edgers. This genuine OEM part is made out of high quality, durable metal material meant to withstand exposure to the elements and general wear and tear over long-term usage.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This key is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Husky, Yard Machines, Huskee, Montgomery Wards, Yard Man, and MasterCut.

This is a replacement bell washer, a flat washer that can be used with a wide range of various types of lawn and garden equipment. The inner dimension of this washer is 0.40 inches, while the outer dimension is 0.88 inches. Washers are typically used as a way to help ensure a tight connection when used with bolts or screws. They will also help to distribute the pressure of the connection and reduce the risk of corrosion. Washers will also provide some protection from damage during installation. Washers could need to be replaced for any number of reasons. In some cases, they might have become corroded or worn down over time. This could mean they no longer provide a solid and secure connection. Other times, the washer could become lost while working on the machine. Owners should always be sure that they replace any lost or damaged washers right away. Not using washers can reduce the lifespan of the machine. This is a genuine OEM bell washer that is sold individually. It is typically used in lawn mowers, snowblowers, tillers, leaf blowers, string trimmers, log splitters, wood chippers, edgers, and chainsaws. It is compatible with Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut brands.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

This is a replacement bell washer, a flat washer that can be used with a wide range of various types of lawn and garden equipment. The inner dimension of this washer is 0.40 inches, while the outer dimension is 0.88 inches. Washers are typically used as a way to help ensure a tight connection when used with bolts or screws. They will also help to distribute the pressure of the connection and reduce the risk of corrosion. Washers will also provide some protection from damage during installation. Washers could need to be replaced for any number of reasons. In some cases, they might have become corroded or worn down over time. This could mean they no longer provide a solid and secure connection. Other times, the washer could become lost while working on the machine. Owners should always be sure that they replace any lost or damaged washers right away. Not using washers can reduce the lifespan of the machine. This is a genuine OEM bell washer that is sold individually. It is typically used in lawn mowers, snowblowers, tillers, leaf blowers, string trimmers, log splitters, wood chippers, edgers, and chainsaws. It is compatible with Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut brands.

The roll pin, also called a shear pin, is a slender metal piece that fastens the driveshaft to the auger of a snowblower. This pin actually does double duty as a safety device. When moving through the snow-covered ground where objects cannot be seen, sometimes the snow-moving auger will come into contact with something other than snow. Since the driveshaft of the blower will continue to turn regardless of the mobility of the auger, the auger would be destroyed or significantly damaged upon encountering such an object. The roll pin is designed to shear off when the auger suddenly stops so the working parts of the blower are not damaged. Most blowers are designed so that the pins are easily accessible. By rolling the blower so the belly plate is up, it is easy to remove the belly plate and see where the shear pin goes through the driveshaft and connects with the auger. The broken piece of the old pin can be forced through by the new pin by gently tapping it with a hammer. This OEM genuine replacement part is compatible with a number of snowblowers, including Craftsman, Troy-Bilt, MTD, Yard Machines, and Yard-Man.

This replacement part is a flange bushing, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This flange bushing is typically found in snow throwers but is compatible with other devices as well. The flange bushings are an important part of many appliances as they help reduce friction inside the machine. A new flange bushing might be needed if the current ones are broken or damaged in any way. It is common that different machinery needs multiple flange bushings. These small but important parts are placed around tubes or poles and are meant to assist during the rotating or sliding mechanisms. Be sure the machine is completely powered off and cooled down as the area with the bushings is often hot from friction. See the owner's manual for more exact instructions before attempting to replace this part. These flange bushings are sold as a set and are OEM replacement parts. These flange bushings are compatible with lawn equipment made by MTD.

This is a genuine hex nut replacement designed for select MTD outdoor lawn and garden equipment. The hex nut is a piece of standard hardware that may have several applications on different units. It is generally used to secure other hardware, handles, or connections. It may be subject to vibrations and constant pressure, which can result in wear over time. These nuts may also get lost during other repairs or if they come loose. In most cases, the unit will be inoperable until the nut is replaced. This genuine OEM replacement hex nut is designed for use in MTD lawn equipment and engines, along with machines from RYOBI, Troy-Bilt, Husky, Yard-Man, Cub Cadet, Bolens, and Yard Machines. The metal nut will require a wrench to replace but should only take a matter of minutes. This is a left-hand threaded nut that is sold as an individual part. Be sure to allow equipment to cool and always wear gloves when performing repairs. The location and function of this nut will vary depending on the unit in question, but it can be used with chippers, lawn tractors, trimmers, edgers, snow throwers, and cultivators.

Washers are used in various locations on many types of lawn and garden equipment and can help to keep a bolt or screw in place. The washer will also help to spread the load from connection, which can help to reduce the risk of damage. One of the most common reasons to replace a washer is if the current washer is lost. If the washer is corroded or if it has been bent or otherwise damaged, it should be replaced, as well. Replacing a washer is generally easy, but this can depend on the location of the washer that needs to be replaced. The authentic OEM replacement flat washer is sold individually. Having several of these available for future needs is a good idea. The washer can be used on snowblowers, lawn mowers, tillers, edgers, log splitters, chainsaws, and wood chippers. Compatible brands include Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, and MasterCut.

This is a self-tapping screw that can be used on a wide variety of lawn and garden equipment in many applications. A self-tapping screw is used to secure metal, wood, plastic, and brick together. When using a self-tapping screw, there's no need to drill a pilot hole since the screw makes its own hole. The only exception is with metal, which will still need a drilled hole before installation. There are many situations when a screw may need to be replaced. Some screws are damaged or broken, while others can become loose and no longer hold materials together. Screw heads can become stripped, which will also mean they need to be replaced. A visual inspection can often give an indication of whether you should replace a self-tapping screw. This is a genuine OEM hex head screw that can be used on various lawn and garden equipment, including wood chippers, lawn mowers, snowblowers, log splitters, tillers, edgers, and leaf blowers. It's compatible with products by MasterCut, Craftsman, Turf King, Cub Cadet, Yard-Man, Ryobi, Bolens, Troy-Bilt, Montgomery Wards, Murray, Huskee, Yard Machines, MTD, and more. This screw is sold individually.

This is a shear bolt, also known as a shear pin, which is used in many models of snowblowers. The shear bolt connects the auger shaft to the auger on the tool. This connection allows the augers to rotate, collecting snow and sending it to the impeller fan. Most snowblowers have at least one shear pin on each side of the auger gearcase. Large objects that get stuck between the housing and augers can damage the pins, necessitating replacement.If there is damage to the shear bolt or if it has broken, the snowblower may not work as expected. To replace the bolt, the snowblower should be turned off. Wear work gloves and remove the spark plug wire before disassembling the snowblower to reach the shear bolt. It can be removed and replaced with a new part.This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The shear bolt is designed for use with snowblowers created by Yard-Man, Yard Machines, MTD, Montgomery Wards, and Huskee.

This replacement part is a pinion gear. This is a genuine replacement part made by MTD. This part is small but important to many different appliances. Pinion gears have ridges that are able to connect to other parts and typically rotate or turn in specific ways so that the engine operates properly.A new pinion gear might be needed if the current one is stripped down due to friction over time. If the user hears noises coming from inside the machine, the gears may be out of place or damaged. Work gloves are recommended during this repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer."

This is an MTD flat washer for lawn and garden equipment. Flat washers are a standard piece of hardware typically used with bolts or screws to better secure components in place. If a flat washer is corroded or broken, or if it is missing, it should be replaced.To install a flat washer, simply slide it into place while reinstalling a screw or bolt. If working near an engine, ensure that the equipment is completely cool before installing this part.This is a genuine OEM part compatible with lawn and garden equipment manufactured by Craftsman, MTD, Cub Cadet, Troybilt, and Yard-Man. Washers are sold individually.

This carriage bolt is a self-locking fastener made for use in round or square holes to attach metal to metal in outdoor equipment. These bolts provide an added safety feature because they can only be removed from one side. Carriage bolts can carry a large amount of weight, which makes them ideal for use in outdoor yard equipment. Carriage bolts may be used to attach a lawn mower's arm to the side support and other similar applications. If the bolt needs to be replaced, removal and installation are simple. Use a wrench to loosen the nut holding the washer and bolt in place. Once the nut is loose, the bolt can be unthreaded by hand and pulled out of the hole. To install, push the bolt back through the hole. If the fit is too tight to install by hand, use a hammer to tap it in place. Reinstall the washer and nut and tighten with a wrench.This carriage bolt is designed for use in lawnmowers, snowblowers, and lawn tractors manufactured by Craftsman, Bolens, Yard Machines, Yard-Man, and MTD. This is a genuine OEM product that comes directly from the manufacturer. Note: It does not come with a nut or washer.

This carriage bolt is a self-locking fastener made for use in round or square holes to attach metal to metal in outdoor equipment. These bolts provide an added safety feature because they can only be removed from one side. Carriage bolts can carry a large amount of weight, which makes them ideal for use in outdoor yard equipment. Carriage bolts may be used to attach a lawn mower's arm to the side support and other similar applications. If the bolt needs to be replaced, removal and installation are simple. Use a wrench to loosen the nut holding the washer and bolt in place. Once the nut is loose, the bolt can be unthreaded by hand and pulled out of the hole. To install, push the bolt back through the hole. If the fit is too tight to install by hand, use a hammer to tap it in place. Reinstall the washer and nut and tighten with a wrench.This carriage bolt is designed for use in lawnmowers, snowblowers, and lawn tractors manufactured by Craftsman, Bolens, Yard Machines, Yard-Man, and MTD. This is a genuine OEM product that comes directly from the manufacturer. Note: It does not come with a nut or washer.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

A star knob connects the upper and lower handles on an outdoor appliance, and if removed, the upper and lower handles are quick-released. This part is made of black heavy-duty black plastic, and the threads are made of steel. Over time, the threading can become worn out, making the connection loose, and causing the two handles to no longer stay in place. Star knobs are a straightforward repair that can be done in a matter of minutes. Just unscrew the original, damaged knob and screw in the new knob. The knob is designed to be unscrewed by hand, so there is no need for additional tools to make this repair. This genuine OEM replacement part is designed for a variety of outdoor appliances, including lawnmowers, edgers, chippers, tractors, trimmers, and cultivators. This star knob is compatible with Yard Machines, Yard-Man, Cub Cadet, Bolens, Craftsmen, and Ryobi products. This part ships individually.

This center hex nut is a genuine MTD part, sold individually. This center hex nut can be used as a replacement part in lawn mowers, snowblowers, tillers, leaf blowers, edgers, log splitters, and wood chippers. The purpose of the center hex nut for one of these small engine outdoor appliances is to work in conjunction with a bolt to provide a fastening component for one or more parts within the internal mechanisms of the appliance.The center hex nut might need to be replaced if the small fastening component is lost, misplaced, or damaged within the typical lifespan of the small engine outdoor appliance in which it has been installed.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This center hex nut is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Husky, Yard Machines, Huskee, Montgomery Wards, Yard Man, and MasterCut.