Need Help?
Call
This is a high-quality refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with refrigerators made by Kenmore, Whirlpool, Maytag, and KitchenAid.
Fix a washer that won't advance cycles, stops mid-cycle, or runs continuously. This control timer regulates wash and spin durations. 30-minute repair.
Well it was easier it took me less than 30 minutes and my hasher is ready to be used thankyou. Read more
This is an electronic control board that manages the surface (cooktop) heating elements on an electric range. It includes a potentiometer and display panel that regulate element power levels and show settings. Replace this board if your cooktop burners fail to heat properly, cycle erratically, or if the surface element display is unresponsive or showing error codes.
Part came in fast and was easy to put on. Turn off elect. and take front panel up , replace part and put back pannel. Read more
Won't start, spin light blinking, or won't stop spinning? This control board manages cycles and settings. Common DIY repair, typically installed in minutes.
Remove the 2 screws that hold on the front cover just above the washer, the control board is in front of you. Remove the 2 small screws that secure the board, they are star screws, very small ones, do not drop them, for they will fall into the washer tub. Take a picture of the wiring harness, press the 2 tabs on each side of the board, left and right side, the board will pop out. replace the wiring harness, wiring harness has tabs that hold them in place. Also, check the magnetic lid switch,... Read more
Washer won't advance through cycles or gets stuck in fill mode? A faulty timer prevents proper cycle progression. Restores automatic advancement.
Replaced the timer Read more
If your dryer won't shut off or cycles won't advance, the timer may have failed. This control manages drying cycles and run time. DIY repair in 20 minutes.
With a Phillips screw driver, on the back of the control panel there was about 6 or 7 screws to undo, to take the cover off and 2 screws holding the timer in place. Just undone those, took out old timer, made sure I took wires from old timer one at a time, and, put on new timer. Put everything back, although I had to find a couple of very small washers to make the timer fit tight, in the 2 holes it came out of. Luckily I had those or would of been a very loose timer. Very easy to do. Read more
This refrigerator electronic control board manages key cooling and defrost functions. Replacing a failed board helps restore accurate temperature regulation and responsive operation so the appliance runs as designed.
I replaced the control board. Read more
Fix F11, F14, or E15 error codes and unresponsive controls. This electronic control board restores oven temperature regulation and display functions.
My induction slide-in range was getting an E15 error code. First thing to do is look in the service manual, which should be in a plastic pocket at the back of the oven. I eventually did do that, but first I googled it. First, power cycle the stove, i.e. turn off the breaker, wait a minute, then turn it back on. That fixed it for a few months, but then it started doing it again, except now it only took a minute for the oven to beep E15 after turning the breaker back on. The service manual... Read more
Fix error codes or blank digital displays with this range main control board assembly. Restores temperature control and burner functions. DIY-friendly.
Replaced with this igniter. Read more
Fix an oven that won't heat, shows error codes, or has unresponsive controls. This main control board coordinates timing and powers key components.
Fix unresponsive controls, erratic cycles, or error codes with this dishwasher electronic control board. Restores proper timing and operation.
Fix your oven that won't heat, maintain temperature, or respond to controls with this electronic control board. Monitors bake, broil, and warm functions.
Fix unresponsive controls, blinking displays, or oven won't heat. This electronic control board restores full function. Straightforward DIY install.
Replaced Control box, Very easy to install. Remember to DISCONNECT power cord. Read more
Fix a worn or cracked start button area on your trash compactor with this peel-and-stick control panel insert. Easy 5-minute DIY repair restores appearance.
Placed screwdriver into start button hole to pry up and remove old faceplate then cleaned surface. Peeled off adhesive backing on new faceplate and reinstalled. Looks perfect and took less than 5 minutes. Read more
Fix an oven that won't turn off or won't maintain temperature. This relay board controls power to bake and broil elements. Moderate DIY repair.
Replaced the relay circuit board. Read more
Fix a washer that won't advance cycles, stops mid-cycle, or hums but won't spin. This mechanical timer controls wash sequences. DIY-friendly repair.
Appliance Parts Pros I've used in the past and will continue to use, now they have a video showing step by step how to change the part your going to purchase, video also explains what the part does and symptoms of bad existing parts like mine. Washer machine was dripping water into tank when not in use, it was the water inlet valve. I purchased on a Sunday and it arrived with our mailman on Wednesday. I watched the repair video one more time and changed it out. When you unhook hoses to remove... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.