By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
Won't start, spin light blinking, or won't stop spinning? This control board manages cycles and settings. Common DIY repair, typically installed in minutes.
Remove the 2 screws that hold on the front cover just above the washer, the control board is in front of you. Remove the 2 small screws that secure the board, they are star screws, very small ones, do not drop them, for they will fall into the washer tub. Take a picture of the wiring harness, press the 2 tabs on each side of the board, left and right side, the board will pop out. replace the wiring harness, wiring harness has tabs that hold them in place. Also, check the magnetic lid switch,... Read more
This is a 60 Hz timer that controls the duration of drying cycles in a clothes dryer. It advances through each stage of the cycle and signals the motor and heating components to turn on or off at the appropriate times. Replace this timer if the dryer will not start, the cycle does not advance, the timer knob spins freely without clicking, or if the dryer runs continuously without shutting off.
I replaced the timer with a new one. Read more
Fix a blank or non-responsive refrigerator display panel with this control board. Restores temperature readout and button functions on the front panel.
Fixes refrigerators that won't cool, have blank displays, or experience blinking lights. Main control board regulates temperature and functions. Moderate DIY.
Fixes refrigerators that won't cool or have excessive frost buildup. This defrost timer cycles frost removal every 6-12 hours. DIY-friendly repair.
This unit has a recurring problem with the defrost timer. after the first 10 years the original part gave up. we had it replaced and (as normal for me i watched very closely) . after 2 years the same trouble started again. the defrost cycle would run to long. so i replaced the same part and solved the trouble again. so now about every 2 years this part wears out again and i order it and replace it. this has gone on for 20 years now and this unit is still going strong after serving us for 29... Read more
This control board is the appliance's primary printed circuit board. It governs cycle timing, options, and power to key components. Replacing a failed PCB can restore responsive controls and consistent operation across all cycles.
After doing online research about this particular error code I found www.appliancepartspros.com. On the site I searched my washing machine's model number and I found the correct part (in my case, it was the main control board) at a discounted price. I figured that with their no hassle return policy it was a no brainer trying to replace the part myself. The process went fairly smooth. If you're replacing this part yourself, be sure to disconnect your machine from the power outlet first to avoid... Read more
This is the electronic control board located behind the user interface panel on the front of the refrigerator, responsible for processing temperature settings, display readouts, and user inputs. It communicates your selected settings to the main control board to regulate cooling functions. Replace this board if the display is blank, unresponsive, shows error codes, or if temperature adjustments no longer take effect.
Range won't turn off or functions stay powered on? This relay board controls electrical flow to range components. Common fix for stuck-on appliances.
Fix a washer that won't advance cycles, stops mid-cycle, or hums but won't spin. This mechanical timer controls wash sequences. DIY-friendly repair.
Appliance Parts Pros I've used in the past and will continue to use, now they have a video showing step by step how to change the part your going to purchase, video also explains what the part does and symptoms of bad existing parts like mine. Washer machine was dripping water into tank when not in use, it was the water inlet valve. I purchased on a Sunday and it arrived with our mailman on Wednesday. I watched the repair video one more time and changed it out. When you unhook hoses to remove... Read more
Washer won't advance cycles or stops mid-cycle? This timer sequences fill, wash, drain, and spin stages. Moderate DIY repair restores cycle control.
Watched instructional viedeos on how to replace timer. Read more
Fix temperature fluctuations and inconsistent cooling. This refrigerator control board regulates defrost and temperature. DIY-friendly replacement.
In the past the temperature would change from one day to the next, remain constant for weeks then start rising again. Would unplug for 5 – 10 min and adjust temp and would work fine. Now Refrigerator compressor will not shut off (has been running for the last 3 days) temps are 26F on freezer side and 43F on food compartment side. Checked evaporator and it has a great deal of frost on it but not frozen. Checked for continuity on the defroster heater and thermostat by going through the... Read more
Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. If you require the Jumper Wire that goes with certain models, the part number is 00167782.
This is a common problem with the Bosch product evidently. After watching the on-line instructional video, I ordered the control module from APP. The part arrived quickly and the replacement of the module was very easy. Within 10 minutes of starting the project, the dishwasher was repaired at a fraction of what it would have cost for a service call. Read more
Washer won't start, stops mid-cycle, or displays error codes? The main control board manages all cycle functions. Moderate DIY repair, 30-45 minutes.
I had a beeping problem with my washer whereby it kept on beeping when I turned it on. After researching the issue online I saw that the control panel was the issue so I ordered a new one and installed it and voila!!! Problem solved!! It was an easy fix and the only hard part was lifting the dryer from the washer so as to replace the part. Read more
Fix an oven that won't heat or respond to controls with this electronic control board. Restores accurate temperature regulation and normal operation.
I replaced the digital oven controller. Read more
Fix F11, F14, or E15 error codes and unresponsive controls. This electronic control board restores oven temperature regulation and display functions.
My induction slide-in range was getting an E15 error code. First thing to do is look in the service manual, which should be in a plastic pocket at the back of the oven. I eventually did do that, but first I googled it. First, power cycle the stove, i.e. turn off the breaker, wait a minute, then turn it back on. That fixed it for a few months, but then it started doing it again, except now it only took a minute for the oven to beep E15 after turning the breaker back on. The service manual... Read more
Fix temperature fluctuations, defrost issues, or error codes with a new main control board. Controls cooling, defrost cycles, and display functions.
Replaced the main control board. Read more
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.