Parts for Whirlpool WTW4850HW0: Controls And Water Inlet Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This control console houses the appliance's user controls and display so you can operate cycles and settings reliably. It restores a damaged or nonfunctional front control area for safer, more accurate use. What it does

• Provides the mounting and interface for buttons, knobs, and display so selections register correctly
• Replaces cracked, melted, or cosmetically damaged front-control surfaces
• Can resolve unresponsive or intermittent button/selector behavior when caused by a damaged console
• Restores proper alignment and protection for internal control components

• One console (control panel assembly) as shown

• Disconnect power (and gas supply for gas appliances) before starting work
• Handle the display and button areas carefully to avoid damage to delicate switch and ribbon connections
• Retain mounting screws and trim; some panels use clips that must be flexed for removal/installation

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wire harness routes power and control signals between the appliance's electrical components, restoring proper connectivity and operation when the original harness is damaged or faulty. It's a direct-fit electrical assembly designed for straightforward replacement. What it does:

• Provides the main electrical connections between control, power source, and other components
• Replaces damaged, frayed, or burned wiring that can cause intermittent or complete loss of function
• Helps eliminate symptoms like no power to controls, intermittent operation, or blown fuses/trips
• Maintains factory-style connector fit and routing to reduce vibration and wear

• One complete wire harness assembly

• Always disconnect power (unplug or shut off circuit breaker) before inspecting or replacing wiring
• Route harness and secure connectors per the appliance wiring diagram to avoid pinching or heat exposure

Note: 2-Position Switch

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Note: 5  Position Switch
 

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This replacement power cord provides the main electrical connection for your appliance so it can receive power safely and reliably. Designed as a direct-fit replacement where the original cord is worn or damaged. What it does:

• Delivers mains power to the appliance so controls and heating/cooling components can operate
• Replaces damaged, frayed, or burned cords that can cause intermittent power or no power
• Restores a secure connection at the appliance terminal block and reduces risk of arcing
• Helps eliminate issues caused by loose or broken power leads

• Disconnect power at the breaker or unplug the appliance before starting any work
• Access the terminal block or cord connection point
• Ensure terminal screws are tight and any strain-relief clamp is installed correctly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Knob is an OEM part for Whirlpool dryers. It attaches to the control shaft or stem located behind the dryer control panel. 

Causes of a bad knob can include wear and tear over time, exposure to heat and moisture from drying cycles, accidental damage, improper cleaning techniques, or compatibility issues where the knob no longer fits correctly on the control shaft.  

Symptoms of a bad knob include:

• Knob difficult to turn or jammed in certain positions
• Knob incorrectly labeled so settings are unclear  
• Loose, cracked, or missing knob that does not securely interface with the control panel

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A replacement control knob that restores user control of settings and makes selection easy. Installs on the appliance control shaft to provide a solid grip and clear tactile feedback for reliable operation. What it does:

• Replaces a cracked, worn, missing, or hard-to-turn control knob
• Allows selection of temperature, cycle, or speed settings depending on the original control
• Stops slipping or spinning issues caused by damaged splines or stripped knob bores
• Restores safe, predictable control operation so you can use the appliance as intended

• Disconnect power (and gas if applicable) before servicing the appliance
• Most installations are push-on: align the knob splines with the control shaft and press firmly until seated
• Inspect the control shaft for damage; replace the switch or shaft if the knob does not seat securely

4 - Position Switch

This wire harness is the main electrical connection assembly that links the appliance's control and power components, restoring reliable circuit continuity and proper operation. It replaces damaged or worn wiring to help eliminate intermittent power and control faults. What it does:

• Provides factory-style wiring connections between controls, switches, and power inputs
• Restores proper circuit continuity to address intermittent operation, loss of power, or non-responsive controls
• Ensures secure connector fit to prevent arcing or loose connections
• Matches OEM routing and terminal configurations for correct installation

• Always disconnect power before servicing the appliance to avoid shock or injury
• Compare the harness and connectors to the original part for correct fit before installation
• Route and secure wiring per the appliance wiring diagram; avoid pinching or contact with sharp edges or hot surfaces

The Washer Water Inlet Valve is an OEM part for Whirlpool washing machines. This valve controls the flow of water into the washer, opening and closing to allow the correct amount of hot and cold water into the machine during different stages of the wash cycle.

Causes of a bad water inlet valve can include wear and tear over time, sediment build-up, or damage from high water pressure. These issues can cause the valve to malfunction, leading to improper water levels or no water entering the machine at all.

Symptoms of a bad water inlet valve include:

• Washer not filling with water
• Slow fill or no water flow
• Water leaking from the valve area
• Inconsistent water temperature during cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.