Parts for Maytag MSS25C4MGB00: Dispenser Parts

The Whirlpool EveryDrop Ice and Refrigerator Water Filter 1 is an OEM replacement part for Whirlpool refrigerators. This filter works to remove small particles from water to ensure clean, great-tasting ice and drinking water directly from the refrigerator door.  Measuring approximately 2.50 x 2.50 x 8.69 inches, this filter is easy to install. 

For optimal performance, we recommend replacing the filter every six months. The filter material is made from coconut carbon block, which has a micron rating of 0.5 and a flow rate of 0.5 gpm. The filter is designed to operate at a maximum pressure of 125 psi and an operating temperature of 38-100°.

Symptoms of a filter needing replacement include:

• Gradual decline in water/ice quality over time exhibiting muddy appearance or odd tastes
• Filter life indicator appears showing it is time for a new one 

Causes stem from normal usage over the stated capacity of the original filter. Allowing one to expire could produce unhealthy water.

This OEM replacement part is compatible with select Maytag, Jenn-Air, and Amana models as well.

This genuine replacement fitting connects appliance water or fluid lines to internal plumbing, restoring a secure seal and proper flow. Use it to replace a worn or damaged connector and stop leaks or loose hose connections. What it does:

• Provides a sealed connection between a hose and the appliance plumbing
• Helps stop leaks from cracked, corroded, or loose fittings
• Restores reliable water or fluid flow through the supply line
• Fits where the original factory connector was used

• One replacement fitting as shown

• Turn off water and disconnect power to the appliance before starting
• Inspect and replace any worn O-rings or gaskets as needed
• Hand-start threads, then tighten to factory torque; avoid over-tightening

This ice door is the replacement chute door that seals the ice dispenser and helps keep ice cold and contained in the dispenser opening. It restores proper closing and helps prevent warm air or debris from entering the ice chute. What it does

• Replaces the dispenser chute door that opens to allow ice to pass and closes to seal the ice compartment.
• Helps prevent melted ice, spills, or debris from entering the dispenser area.
• Can stop continuous dripping or airflow through the chute when the door fails to close fully.
• Supports normal dispenser operation by providing a proper pivot/closure surface.

• One ice door (single dispenser chute door) as shown.

• Unplug the refrigerator before starting any repair to avoid injury.
• Remove any ice from the dispenser area and follow the OEM instructions for removing the dispenser bezel or access panel.
• Handle the plastic parts carefully to avoid cracking; align pivots/posts and test the door for full opening/closing before reassembly.
• If the door uses small clips or screws, keep hardware organized and reuse only OEM-specified fasteners.

This replacement ice door seals and covers the ice chute on the freezer door so the dispenser works properly and cold air stays inside the freezer. It helps restore normal dispensing and keeps the ice compartment protected from warm air. What it does:

• Covers the ice chute and seals the dispenser opening to help maintain freezer temperature
• Opens and closes with each dispense to control ice flow and prevent warm air entry
• Helps prevent ice clumping or melting near the dispenser area
• Commonly replaced when the door is cracked, warped, stuck, or does not close properly

• Disconnect power to the appliance before beginning any repair
• Remove the ice bin/door trim as instructed by your model's service instructions to access the door
• Handle plastic parts carefully to avoid cracking; align mounting tabs before fastening
• After installation, test the dispenser to ensure the door opens and closes smoothly

The Dispenser Funnel Guide Ice Door is an OEM part for Whirlpool refrigerators. It is responsible for guiding ice from the ice dispenser on the door into your glass.

A bad dispenser funnel guide ice door can occur due to regular use, wear and tear, or damage caused by foreign objects. If you notice ice not dispensing properly or falling outside of your glass, it may indicate a problem with the dispenser funnel guide ice door.

Symptoms of a bad dispenser funnel guide ice door include:

• Ice not dispensing into the glass or container properly
• Ice falling outside of the glass during dispensing
• Difficulty in activating the ice dispenser or inconsistent ice flow

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This retainer is a small mounting clip that secures an appliance component or assembly in place to prevent shifting and reduce noise or wear. It restores proper fit and alignment where a worn or broken clip allows movement. What it does:

• Holds panels, trim, or small assemblies securely to their mounting points
• Prevents rattling, shifting, or misalignment caused by a missing or damaged clip
• Helps maintain proper spacing so seals and connections stay aligned
• Works as a direct-fit replacement when the original retainer is broken or missing

• One retainer

• Disconnect power and, if applicable, water supply before starting any repair
• Remove surrounding fasteners or trim gently to access the clip; avoid forcing plastic tabs to prevent breakage
• Replace with the exact part number and ensure the component is seated fully before reassembling

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing