Parts for Maytag MGD5500FC0: 06 - Door Parts

The Inner Door is an OEM part for Whirlpool dryers. It forms the inner layer of the dryer door, providing insulation and protection for the drum and other internal parts.

A bad inner door can be caused by regular use, accidental damage, or wear and tear over time. If you notice issues such as cracks, dents, or a loose inner door, it may indicate a problem with the inner door.

Symptoms of a bad inner door include:

• Visible cracks or damage on the inner door
• Difficulty in closing or latching the door properly
• Increased noise or vibration during the drying cycle

Replace your faulty inner door with this genuine OEM part to restore your dryer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Washer/Dryer Door Hinge is an OEM replacement part for Whirlpool washer and dryer units. It is a component that allows the appliance door to open and close smoothly while providing a secure attachment point to the main cabinet.

Symptoms of a bad washer/dryer door hinge:

• Difficulty in opening or closing the door
• Door sagging or not aligning correctly when closed
• Excessive noise or rattling when the door is opened or closed
• Water leaks or air leaks around the door area

Causes of a bad door hinge can include mechanical wear and tear over time, physical damage due to impact or mishandling, or improper installation or alignment of the hinge components.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer and dryer models.

This replacement door handle provides a secure grip to open and close the appliance door and restores normal door operation and appearance. Durable molded construction matches the original fit and finish. What it does

• Replaces a cracked, broken or worn door handle to restore safe opening and closing
• Provides a stable grip for pulling the door open or pushing it closed
• Helps maintain proper door alignment and seal by securing the outer door panel
• Fits where the original handle has become loose, damaged or cosmetically worn

• Disconnect power and any water supply before starting work; follow basic appliance safety procedures.
• Handle typically attaches with factory screws or retaining clips—retain original fasteners if possible.
• Inspect mounting area for damage and replace any broken clips or screws for secure installation.

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

The Hinge Pin Bushing is an OEM part designed for Whirlpool washing machines that is responsible for providing a pivot point for the hinge pin and ensuring the door opens and closes smoothly and securely. Over time, this bushing can wear out or become damaged, leading to issues with the door's alignment and opening.

Symptoms of a bad Hinge Pin Bushing include:

• Difficulty in opening or closing the door
• Noise when the door is moved
• Loose or wobbly door 
• The door not staying closed

Causes of a bad hinge pin bushing can range from normal wear and tear to excessive force used on the door or lid. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This door catch assembly secures the door by engaging the mating latch or strike, keeping it firmly closed for proper operation and safety. Replace a worn or broken catch to restore reliable door closure and consistent performance. What it does

• Engages the door latch/strike to hold the door closed during use
• Helps maintain proper door alignment and contact with seals/interlocks
• Restores a positive latch feel and consistent closure
• Common signs of wear: door won't latch or pops open, must be slammed to close, visible damage to catch tabs

• One door catch assembly

• Unplug the appliance or switch off power at the breaker before servicing; for gas appliances, shut off the gas supply
• Open the door, access the catch at the cabinet/frame, and remove retaining screws or clips
• Transfer any reusable hardware from the original part and install the new catch
• Verify smooth latch engagement and door alignment before restoring power

This replacement cover is a cabinet access panel that protects internal components and restores a finished appearance. It keeps components shielded from dust and debris while helping maintain safe, stable operation of the appliance. What it does:

• Shields internal parts and wiring from debris, spills, and accidental contact
• Restores the appliance's exterior finish and maintains proper panel alignment
• Helps reduce noise and vibration by securing the cabinet opening
• Commonly replaced when the panel is cracked, bent, missing, or loose

• One cover

• Disconnect power to the appliance before beginning any work
• Removal/installation typically requires basic hand tools; handle part carefully to avoid scratches
• Follow the manufacturer's service instructions for correct fitment and fastener torque
• If you see damaged clips or fasteners, replace them as needed to ensure a secure fit

This complete door assembly replaces a damaged or worn oven door to restore proper sealing and safe operation. It provides the outer structure and handle interface needed for opening, closing, and maintaining internal temperatures. What it does

• Replaces a broken, dented, or warped door to help restore proper closure and heat retention.
• Restores a secure latch and alignment so the appliance opens and closes smoothly.
• Reduces heat loss and helps prevent uneven cooking caused by a poor seal.
• Helps eliminate rattling or vibration from a loose or damaged door.

• High-level replacement; handle the glass and edges carefully to avoid cuts or breakage.
• Disconnect power (and gas supply for gas appliances) before removing the old door.
• Follow manufacturer instructions for door removal and reinstallation; two people may be required for safe handling.
• If the door includes glass or internal clips, inspect for secure seating and tightened fasteners after installation.

This retainer is a small mounting clip that secures internal appliance components, keeping parts aligned and preventing vibration or rattling. Replacing a worn or broken retainer restores proper fit and helps reduce noise and movement. What it does:

• Secures a specific internal component to its mounting point to maintain proper alignment
• Keeps parts from shifting or vibrating during operation
• Helps prevent intermittent noise caused by loose fittings
• Supports reliable operation by holding components in the correct position

• One retainer clip

• Disconnect power to the appliance before beginning any work
• Inspect the surrounding mounting area and matching mating tabs for damage before installing
• Install the retainer by aligning it to the mating slots and snapping or fastening it into place; use gentle pressure to avoid breakage
• If other mounting hardware or adjacent parts are damaged, replace them as well for a secure fit

This replacement window is the exterior glass panel that fits the appliance door, restoring visibility and protecting internal components. It gives a clear view inside while helping keep heat, steam, and debris contained during operation. What it does:

• Replaces cracked, chipped, or shattered door glass to restore a clear viewing area
• Protects internal parts from spills, splashes, and cooking residue
• Helps maintain proper cabinet seal and consistent interior conditions
• Reduces heat loss and prevents direct exposure to internal heating elements

• Disconnect power to the appliance and allow all surfaces to fully cool before starting
• Wear cut-resistant gloves and eye protection; handle glass carefully to avoid injury
• Follow manufacturer instructions for removing the door assembly and replacing the glass

This Medallion decorative emblem restores the appliance's factory appearance by replacing a missing, faded, or damaged nameplate. It gives a finished look to the control area or exterior trim. What it does:

• Replaces a worn, cracked, or discolored emblem to improve the appliance's appearance
• Covers the factory logo/label area and restores original styling
• Helps prevent dirt buildup behind a missing trim piece when properly installed
• Matches the OEM shape and finish for a seamless fit

• One Medallion decorative emblem

• Use the factory fasteners or adhesive method shown in your appliance's parts diagram; refer to the diagram for exact attachment style
• Disconnect power to the appliance before attempting any repair that requires removing trim or control panels
• Handle carefully to avoid scratching the finish; alignment may require gentle pressure or clips to seat properly

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.