Parts for Whirlpool WFW85HEFC0: 03 - Door Parts

The Washer/Dryer Door Hinge is an OEM replacement part for Whirlpool washer and dryer units. It is a component that allows the appliance door to open and close smoothly while providing a secure attachment point to the main cabinet.

Symptoms of a bad washer/dryer door hinge:

• Difficulty in opening or closing the door
• Door sagging or not aligning correctly when closed
• Excessive noise or rattling when the door is opened or closed
• Water leaks or air leaks around the door area

Causes of a bad door hinge can include mechanical wear and tear over time, physical damage due to impact or mishandling, or improper installation or alignment of the hinge components.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer and dryer models.

The Hinge Pin Bushing is an OEM part designed for Whirlpool washing machines that is responsible for providing a pivot point for the hinge pin and ensuring the door opens and closes smoothly and securely. Over time, this bushing can wear out or become damaged, leading to issues with the door's alignment and opening.

Symptoms of a bad Hinge Pin Bushing include:

• Difficulty in opening or closing the door
• Noise when the door is moved
• Loose or wobbly door 
• The door not staying closed

Causes of a bad hinge pin bushing can range from normal wear and tear to excessive force used on the door or lid. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

The Door Strike is an OEM part for Whirlpool washing machines. This component engages with the door latch to securely close the washing machine door. Ensuring a tight seal, the door strike plays a pivotal role in the appliance's safety mechanisms, preventing the washer from operating if the door is not properly shut. 

Causes for replacement often stem from physical damage, such as breaking or bending due to forceful closing of the door, normal wear and tear, or manufacturing defects that prevent the door from latching correctly. 

Symptoms of a bad Door Strike include:

• The washing machine door won't latch or lock properly.
• The washer fails to start due to the door not being recognized as closed.
• Visible damage or wear to the strike, indicating it may not engage correctly with the latch.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This inner door panel restores the washer lid's interior finish and structural support, helping the lid close and seal properly. It replaces a cracked, dented, or cosmetically damaged inner door to improve appearance and function. What it does:

• Provides the interior surface and mounting points for the washer top lid assembly
• Restores proper lid alignment and helps the lid close smoothly
• Eliminates sharp edges or cosmetic damage from a cracked or dented inner door
• Helps maintain correct fit with the outer door and lid components

• One inner door panel

• Disconnect power and water supply before starting any repair
• Remove the outer lid and related fasteners to access and replace the inner panel
• Keep track of screws and clips; hand-tighten fasteners to avoid stripping

A small metal hose clamp that secures flexible hoses and tubing to fittings to help prevent leaks and keep connections tight. Simple, durable replacement for worn or loose clamps on appliance water and drain lines. What it does:

• Holds a hose or tube firmly on a barb or fitting to prevent leaks or disconnection
• Resists loosening from vibration and normal use
• Restores a secure connection when an old clamp is corroded, stretched, or broken
• Helps prevent water damage from loose plumbing connections

• One metal hose clamp

• Disconnect power and shut off water supply before servicing
• Slide clamp over hose, position over fitting barb, then compress or tighten as required
• Replace any damaged hoses or fittings when installing a new clamp
• Verify a leak-free connection before returning appliance to service

NOTE: Door glass. Made out of Acrylic plastic. On some models, there is a triangular shaped notch that may have to be cut off in order for the glass to fit.

The Inner Door Glass is an OEM part for Whirlpool washing machines. As a key component providing visibility, the inner door glass allows users to monitor wash cycles without repeatedly opening the washer door. It is situated securely within the protective outer door paneling.

Causes of damaged inner door glass can include cracks or chips resulting from normal wear and tear, excessive impacts from clothing or coins, or improper cleaning techniques.

Symptoms of a bad inner door glass include:

• Reduced visibility into the washer during operation
• Leaks or moisture entering around the damaged glass
• Physical cracks, chips or debris visible on the glass pane
• Inability to securely latch or seal the washer door closed

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.