Parts for Bosch B36CL80ENS/01: Evaporator Parts

This heating element is the oven/dryer-style heater assembly that provides controlled heat for drying or cooking cycles, restoring proper temperature during operation. It fits specific Bosch appliances. What it does

• Heats the appliance interior so dryers can remove moisture or ovens can reach set temperatures.
• Restores normal heating when a failed element causes no heat or weak heat.
• Works with the appliance's thermostat and controls to maintain set temperatures.
• Common symptom: no heat, insufficient heat, or longer cycles.

• Disconnect power (and gas, if applicable) before starting any repair.
• Removal typically requires access to the appliance's rear or front panel; follow the OEM service manual.
• Inspect and test related parts (thermal fuse, thermostat, wiring) if heating problems persist.

This thermal fuse is a one-time temperature safety cutoff that stops power when overheating is detected, protecting the appliance and reducing fire risk. It's a direct-replacement safety device for units that use a single thermal cutoff. What it does:

• Interrupts electrical flow to the heater or control circuit when excessive temperature is reached
• Prevents the appliance from operating while an over-temperature condition persists
• Common symptom: appliance runs but does not heat or suddenly stops heating
• Common symptom: appliance fails to start or power is cut after overheating

• Intended for service technicians or experienced DIYers only
• Disconnect power before testing or replacing the fuse to avoid shock or injury
• Do not bypass or defeat this safety device; replace with the exact type specified by the manufacturer
• Verify proper airflow and heating system operation after replacement to prevent repeat failures

This replacement cover protects and conceals internal components, restoring a finished appearance and helping keep debris and moisture away from sensitive parts. It's a direct-fit cosmetic and protective housing piece. What it does:

• Protects internal components and wiring from dirt and casual contact
• Helps maintain proper airflow and clearance around covered components
• Restores finished appearance when original cover is cracked, broken, or missing
• Reduces vibration noise caused by loose or missing trim pieces

• Disconnect power (and water if applicable) before servicing the appliance
• Remove access panels or adjacent trim to reach and remove the old cover
• Align tabs or clips and press into place; do not force or bend mounting tabs
• Use basic hand tools; reinstall with care to avoid overtightening

The Switch is an OEM component specifically designed for Bosch refrigerators. It is an electronic control located inside refrigerator doors.  

The switch allows for contactless powering of interior LED lighting and audible alerts when doors are opened. Convenient visibility of contents is provided.

Causes of switch failure can include repeated opening and closing wear over time. Moisture exposure may corrode internal circuitry as well.

Symptoms of a bad switch include:

• Lights fail to turn on when doors are opened
• Audible chimes/alerts ceasing to sound as intended
• Visible damage or corrosion on the switch housing

This OEM Bosch replacement part is also compatible with Thermador, Gaggenau, and some Kenmore refrigerators utilizing corresponding switch technologies. Replacement ensures that intended convenience features remain operational.

This motor drives the dishwasher's circulation/pump assembly to move wash water through the spray arms for proper cleaning. Replacing a worn motor restores water flow and helps return the appliance to normal wash performance. What it does

• Powers the wash/pump assembly to circulate water during the wash and rinse cycles
• Restores normal water flow when the original motor fails or loses torque
• Common symptom fixes: dishwasher leaves dishes poorly cleaned, reduced or no water circulation, humming or stalled motor noise
• Works as the mechanical drive for the pump/impeller that routes wash water through spray arms

• One motor (assembly) as shown

• Disconnect power to the appliance before any service; follow lockout/tagout if applicable
• Turn off water supply and remove lower access panels to reach the pump/motor area
• Handle the motor carefully; confirm electrical connector and mounting orientation before removal
• Replace any gaskets, seals, or impellers separately if damaged or leaking

This is a replacement heating element designed to generate heat for compatible electric appliances, restoring normal drying or cooking performance when the original element fails. Use this genuine-style assembly to recover proper temperature output. What it does:

• Produces the heat required for drying or heating cycles in the appliance.
• Restores expected run-time and effectiveness when a broken element causes no-heat or reduced-heat conditions.
• Helps eliminate symptoms like laundry taking too long to dry, dishes not drying, or cycles that complete without heat.
• Works as the main resistive heating component—does not include thermostats or control electronics.

• Always disconnect power (unplug or switch off circuit breaker) before attempting service.
• Allow the appliance and element to cool fully before handling; wear gloves and eye protection.
• Inspect mounting hardware and wiring; replace any damaged connectors or strain-relief clips.

This temperature sensor senses internal appliance temperature and sends that signal to the control board so the unit can maintain correct operating temperature. Replaces a failed or inaccurate thermistor to restore proper temperature feedback. What it does:

• Measures internal temperature and provides a voltage/resistance signal to the control board
• Helps the control system maintain set temperatures for cooking, cooling, or defrost cycles
• Common symptom: inaccurate temperature readings or inconsistent heating/cooling
• Common symptom: control shows temperature-related error codes or fails to reach set temperature

• Always disconnect power before removing or installing the sensor to avoid shock or damage
• Handle the sensor and its wiring gently; avoid kinking or pulling on the leads
• Some models require partial disassembly for access;

This temperature sensor (thermistor) monitors internal appliance temperature and sends readings to the control board so the unit maintains correct cooling or heating. Replaces a failed sensor to restore accurate temperature control. What it does:

• Measures internal temperature and reports it to the control board
• Helps the appliance maintain set temperatures for food safety and performance
• Faulty sensor can cause incorrect cooling, excessive frost, or frequent cycling
• Works as the sensing element used by the appliance's temperature control system

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the sensor and wiring gently; do not strain or crimp the harness
• Verify correct part fit and electrical connections before reassembly

This replacement cover is a simple exterior access panel that protects internal components and restores a finished appearance. It keeps wiring and mechanisms shielded while keeping the appliance looking complete. What it does:

• Shields internal components from dirt, dust and accidental contact
• Helps reduce noise by covering openings where parts are mounted
• Restores the appliance's finished look if the original cover was cracked or missing
• Can prevent small objects from falling into service areas and causing damage

• Disconnect power to the appliance before beginning any work
• Remove fasteners or clips securing the old cover; keep screws for reuse if applicable
• Align cover carefully to avoid pinching wiring or misplacing mounting tabs