Parts for Frigidaire FG4H2272UF: Freezer & Middle Drawer Parts

The Frigidaire PureSource Ultra II Refrigerator Water & Ice Filter is an OEM part for Frigidaire refrigerators provides clean, fresh-tasting water and ice. This advanced filtration system is specifically engineered to remove impurities and contaminants from your water supply, including lead, chlorine, mercury, and certain pesticides, without removing beneficial fluoride. 

Regular replacement of the water and ice filter is crucial for maintaining the quality of your drinking water and the efficiency of your refrigerator's water and ice dispensing system. Over time, filters can become saturated with contaminants, reducing their effectiveness and potentially impacting the taste and safety of your water.

Symptoms of a filter in need of replacement include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in the water and ice
• The refrigerator's water filter indicator light turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This refrigerator door gasket creates a tight seal around the door opening to keep cold air in, reduce frost, and maintain stable temperatures. Replace a worn seal to stop air leaks and restore cooling performance and efficiency.

• Seals the perimeter of the refrigerator or freezer door to prevent warm air infiltration
• Helps maintain set temperatures and humidity; reduces frost and condensation near the door
• A damaged seal can lead to longer run times or the door not staying closed
• Common signs: tears, cracks, warping, visible gaps, frost along the gasket, moisture on the frame

• Disconnect power before servicing; open the door and remove the old gasket from its retainer
• Allow the new gasket to relax at room temperature; warming it in warm water helps remove kinks
• Clean the door channel; start corners first, then press the gasket fully into the retainer all around
• Close the door and check for uniform contact; adjust hinges/leveling as needed. Use gentle, low heat only to smooth waves

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn or torn seal to restore appliance performance. What it does:

• Creates an airtight seal around the refrigerator door to prevent cold air loss
• Helps stop frost buildup and reduces condensation inside the compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Commonly replaced when the seal is cracked, torn, flattened, or no longer seals

• Always disconnect power to the appliance before starting any repair
• Clean the door channel and remove old adhesive or debris before installing the new gasket
• Press the gasket into the channel evenly; start at one corner and work around the door for a consistent seal
• If needed, warm the gasket slightly to make it more pliable for installation; avoid using open flames or excessive heat

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn or torn seal to restore appliance performance. What it does:

• Creates an airtight seal around the refrigerator door to prevent cold air loss
• Helps stop frost buildup and reduces condensation inside the compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Commonly replaced when the seal is cracked, torn, flattened, or no longer seals

• Always disconnect power to the appliance before starting any repair
• Clean the door channel and remove old adhesive or debris before installing the new gasket
• Press the gasket into the channel evenly; start at one corner and work around the door for a consistent seal
• If needed, warm the gasket slightly to make it more pliable for installation; avoid using open flames or excessive heat

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn or torn seal to restore appliance performance. What it does:

• Creates an airtight seal around the refrigerator door to prevent cold air loss
• Helps stop frost buildup and reduces condensation inside the compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Commonly replaced when the seal is cracked, torn, flattened, or no longer seals

• Always disconnect power to the appliance before starting any repair
• Clean the door channel and remove old adhesive or debris before installing the new gasket
• Press the gasket into the channel evenly; start at one corner and work around the door for a consistent seal
• If needed, warm the gasket slightly to make it more pliable for installation; avoid using open flames or excessive heat

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer

The Door Assembly is an OEM part for Frigidaire freezers. It provides a secure seal and easy access to the freezer compartment.

A bad door assembly can be caused by wear and tear, damage, or issues with the door gasket. When the door assembly becomes faulty, it can result in issues such as a compromised seal, frost or ice buildup, or difficulty in opening and closing the door.

Symptoms of a bad door assembly include:

• excessive frost or ice accumulation
• Difficulty in opening or closing the freezer door
• Warm air entering the freezer compartment
• isible damage or cracks on the door or door gasket

Replace your faulty door assembly with this genuine OEM Frigidaire part to restore your freezer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This LED interior light assembly provides bright, long-lasting illumination for the refrigerator compartment so you can see contents clearly. Designed to replace a dim, flickering, or non-working interior light. What it does:

• Replaces a failed or flickering refrigerator interior light to restore visibility
• Provides cool-running LED illumination with immediate full brightness
• Fits into the refrigerator light housing and connects to the factory wiring
• Helps you locate items quickly and reduces the need to keep the door open

• One LED light assembly

• Disconnect power to the appliance before installing to avoid shock hazard
• Remove the existing lens/cover and unplug the old light assembly from its connector
• Plug in the new assembly, secure the lens/cover, and restore power to test

This is the adhesive faceplate that labels the control buttons on your appliance's user interface. Replacing a worn or unreadable overlay restores clear button markings so you can operate the controls confidently.

• Identifies buttons and functions on the control panel
• Cosmetic/labeling part; does not include electronic controls
• Common symptoms include faded, peeling, or cracked button labels
• Helps when buttons are hard to read or misidentified during use

• Disconnect power before starting
• Clean and dry the panel surface thoroughly to ensure proper adhesion
• Align carefully; once adhered, repositioning is difficult
• Press firmly across the surface to secure and eliminate bubbles

The PC Board is an OEM part for Frigidaire refrigerators. It serves as the control center of your refrigerator, allowing you to adjust settings, monitor temperatures, and access various functions.

A bad PC board can be caused by electrical issues, component failure, or damage. When the user interface and display board become faulty, it can result in issues such as unresponsive controls, inaccurate temperature readings, or a blank display.

Symptoms of a bad PC include:

• Unresponsive buttons or controls on the refrigerator
• Inaccurate temperature readings or inconsistent display
• Blank or flickering display

Replace your faulty PC board with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This handle mounting kit secures a refrigerator or freezer door handle, restoring a solid connection and proper alignment so the handle works reliably and looks finished. Use when handle movement or missing hardware affects operation. What it does:

• Provides the mounting hardware needed to fasten a refrigerator/freezer door handle to the door
• Replaces missing or damaged brackets, fasteners, or mounting pieces that cause a loose or wobbly handle
• Restores secure grip so the door opens and closes with correct handle support
• Helps eliminate rattling or uneven handle alignment at the door surface

• High-level: Remove the handle to access mounting points before installing the kit
• Use the correct fasteners and torque lightly at first, then snug to seat hardware without over-tightening
• Keep parts organized during install and reuse original trim/cover pieces unless they are damaged

This replacement screw secures appliance panels, brackets, and components for a solid, rattle-free fit. Replace stripped, rusted, or missing hardware to restore proper alignment and dependable fastening where this fastener is specified.

• Fastens panels, brackets, trim, or internal parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling noises
• Direct replacement for stripped, rusted, or missing hardware
• Symptoms include loose panels, gaps, or screws that won't tighten

• Disconnect power (and gas/water if applicable) before servicing
• Use the correct driver/bit; hand-start threads to avoid cross-threading
• Replace screws one at a time to maintain alignment
• Snug firmly—do not overtighten into plastic or thin metal

The Refrigerator Freezer Drawer Assembly is an OEM replacement part for Frigidaire bottom-mount refrigerators. It provides a pull-out storage solution accessible from the bottom of the refrigerator. The drawer assembly contains the necessary components to function as a freezer compartment.

Symptoms of a bad drawer assembly include: 

• Difficulty opening or closing the drawer  
• Improper freezing or frost buildup inside
• Temperature fluctuations within the drawer
• Water or air leaks causing freezer burn on contents

Causes may be related to wear and tear over time, particularly on moving parts. Damage from overloading or other mishandling could also impair operation. 

This replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models.

The Refrigerator Freezer Drawer Assembly is an OEM replacement part for Frigidaire bottom-mount refrigerators. It provides a pull-out storage solution accessible from the bottom of the refrigerator. The drawer assembly contains the necessary components to function as a freezer compartment.

Symptoms of a bad drawer assembly include: 

• Difficulty opening or closing the drawer  
• Improper freezing or frost buildup inside
• Temperature fluctuations within the drawer
• Water or air leaks causing freezer burn on contents

Causes may be related to wear and tear over time, particularly on moving parts. Damage from overloading or other mishandling could also impair operation. 

This replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models.

This replacement refrigerator drawer restores a missing, cracked or damaged storage bin so you can keep produce and deli items organized. Durable molded plastic design fits the original cavity and slides into the existing tracks. What it does:

• Replaces a broken, cracked or missing refrigerator storage drawer to restore usable bin space
• Holds produce, deli items or packaged foods and helps keep contents contained
• Slides into existing drawer tracks; restores proper drawer fit and alignment
• Common symptom fix: drawer falls out, won't close fully, is cracked or won't hold items

• Remove all food and empty the compartment before installing
• Slide drawer into the cabinet tracks until it seats; ensure rails align and glide smoothly
• If tracks or rollers are damaged, replace them separately — this part is the drawer only
• Always follow manufacturer safety guidance; unplug power only if accessing electrical components

This basket assembly is the replacement storage basket that holds and organizes items inside the appliance, restoring secure support and proper circulation. It helps keep contents contained and prevents shifting or damage from a cracked or broken basket. What it does:

• Replaces a cracked, broken or worn basket that no longer supports items
• Restores proper storage and prevents items from shifting or falling
• Helps maintain airflow/clearance where applicable so the appliance can operate as intended
• Fits into the existing cabinet/drawer framework and works with original mounting points

• One complete basket assembly as shown

• Installer should unplug or disconnect power and/or shut off water supply before servicing appliance
• Remove the old basket by reversing factory mounting steps; inspect surrounding rails and clips for wear
• Reuse original fasteners if undamaged; replace any broken mounts for a secure fit

This replacement slider is the small plastic guide that helps a drawer, bin or tray move smoothly along its track so the compartment opens and closes reliably. It restores proper alignment and reduces scraping or sticking. What it does:

• Guides and supports a drawer/bin/tray along its track for smooth movement
• Helps restore proper alignment so the compartment closes evenly
• Reduces scraping, binding, and noisy operation during use
• Prevents excess wear on the track and adjacent components

• One replacement slider

• Remove power and empty the drawer/bin before replacing the slider
• Most sliders snap or slide into a track; align and press until it clicks into place
• Inspect the mating track for cracks or debris and clean before installation

This slider is a replacement drawer guide that restores smooth, stable sliding for a refrigerator or freezer drawer. It helps the drawer track properly so contents open and close without sticking or binding. What it does:

• Guides the drawer along its track so it slides in and out smoothly
• Keeps the drawer aligned to prevent tipping or catching on the cabinet
• Replaces a worn, cracked, or missing slider that causes scraping or uneven movement
• Reduces noise from dragging or rubbing during opening and closing

• One slider

• Disconnect power to the appliance before starting any repair
• Remove the affected drawer or bin to access the slider; note orientation for reassembly
• Slide or snap the new slider into the existing track; some sliders secure with a small screw or tab
• Test the drawer movement after installation and re-seat any retaining clips as needed

This part number contains one (1) screw.

The Handle Screw is an OEM part for Frigidaire refrigerators. It is a fastener or screw used to securely attach the refrigerator door handle. Properly installed handles allow for easy opening and closing of refrigerator doors with minimal effort. 

Causes of a bad Handle Screw include damage or wear over time and corrosion that causes the screw to seize or strip. 

Symptoms of a bad Handle Screw are:

• Loose or wobbly door handles
• Difficulty opening the refrigerator door  
• Handles detaching from the door
• Doors that will not stay closed securely

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.