Parts for Ge CSB48WP2NCS1: Fresh Food Shelves Parts

This snack pan assembly is a replacement storage pan designed to hold snacks and small items in the appliance's refrigerated compartment, restoring organized storage and preventing spills from a cracked or damaged pan. What it does

• Provides a dedicated, removable tray for storing snacks and small foods
• Slides into the refrigerator compartment tracks for easy access and removal
• Replaces cracked, warped, or worn snack pans that cause spills or poor fit
• Restores proper storage function and helps keep interior shelves tidy

• Always unplug the appliance or shut off power before installing parts
• Remove food from the compartment and clear surrounding shelves for access
• Handle edges carefully; align the pan with the tracks and slide into place until secured
• Verify smooth operation and proper seating before returning contents to the compartment

This snack pan wire support holds the snack/deli pan or small shelf securely in the refrigerator, restoring stable storage and proper alignment so pans slide and sit without sagging or falling. What it does:

• Supports the snack/deli pan or small wire shelf to prevent sagging and uneven seating
• Keeps pans aligned so they slide smoothly and don't tip or fall
• Stops rattling or shifting caused by a bent or broken support
• Helps maintain organized storage in the compartment where the snack pan sits

• Unplug the appliance or disconnect power before servicing
• Remove the snack pan and any items from the compartment for safe access
• Inspect mounting tabs and slide rails; align and snap or slide the support into place per the original fit
• Handle sharp sheet-metal edges with care and use appropriate tools; replace if mounting tabs are damaged

This front pan seal replaces the worn gasket that seals the refrigerator's front drip/pantry pan, helping keep water contained and directing drainage properly to prevent puddling and odors. Fits the pan edge at the fridge base. What it does

• Creates a tight edge seal along the front of the refrigerator drain/drip pan to keep condensation and defrost water contained.
• Helps direct water toward the drain channel so it can evaporate or flow to the condenser pan.
• Reduces chance of water pooling on the floor near the refrigerator base.
• Can improve odor control by preventing trapped moisture under the pan.

• One front pan seal.

• High-level swap: remove lower kickplate (if present), peel out the old seal and press the new seal into the pan groove; follow OEM instructions for your model.
• Use gentle, even pressure to seat the seal fully into the pan channel; avoid stretching the seal excessively.
• If adhesive is used by the model, only apply OEM-recommended adhesive in small amounts.
• Disconnect power or follow safety steps before working near electrical components.

This inner drawer slide guides and supports a refrigerator drawer/bin so it opens and closes smoothly. Replacing a worn or cracked slide restores proper alignment and easy, consistent movement of the drawer.

• Provides guided travel for the drawer along the cabinet rails
• Helps keep the drawer level and properly aligned to prevent binding
• Replace if the drawer sticks, grinds, jumps track, or won't close fully
• Visible cracks, broken tabs, or excessive wobble indicate a failed slide

• Unplug the refrigerator before servicing; remove the drawer and its contents
• Note the orientation of the old slide and reuse the existing mounting hardware
• Install the new slide in the same position; tighten screws evenly without overtightening
• Test drawer movement and ensure it seats flush and glides smoothly end to end

This right-hand pan side support secures the refrigerator drain/drip pan, helping keep the pan aligned and stable to prevent sagging or movement that can lead to noise or water pooling under the appliance. What it does:

• Holds the drain/drip pan in the correct position at the right side of the cabinet
• Prevents pan sagging that can cause vibration or rubbing noises
• Helps maintain proper pan alignment to reduce the chance of water spills or pooling
• Replaces worn, cracked or broken side supports that no longer secure the pan

• Disconnect power to the appliance before beginning any repair
• Access may require removing the kickplate/grille and/or sliding out the pan
• Handle plastic parts carefully to avoid cracking; confirm correct side (right-hand) before installation
• If fasteners are stripped or damaged, replace them with OEM-recommended hardware

This left-side pan support secures and aligns the refrigerator pan/drawer, restoring stable, level support for smooth drawer movement and proper pan positioning. It's a simple replacement that prevents sagging or misalignment. What it does:

• Supports the refrigerator pan or deli drawer on the left side to keep it level and stable
• Holds the pan in place so drawers slide smoothly and don't catch or tilt
• Failsafe for preventing pan sagging or partial drops when the original clip breaks
• Helps maintain proper airflow and drawer operation by keeping components aligned

• Disconnect power to the appliance before servicing to reduce shock risk
• Remove the pan/drawer per your model's diagram to access the support
• Replacement typically snaps or screws into the same bracket location — align tabs and press firmly until seated
• Inspect adjacent supports and mounting clips; replace any damaged pieces to ensure proper fit

This outer drawer slide supports and guides a refrigerator drawer or pantry pan so it opens and closes smoothly. Replacing a worn or cracked slide restores alignment and helps prevent sticking, tipping, or spills.

• Attaches as the outer rail for the sliding drawer assembly
• Provides smooth gliding action and supports the drawer/pan
• Helps keep the drawer level and properly aligned
• Common symptoms: drawer hard to move, tilts or falls, cracked/broken rail, scraping or binding

• Disconnect power; empty and remove the affected drawer
• Remove the shelf/cover if needed to access the slide
• Take out mounting screws/clips; note the slide's orientation
• Install the new slide, ensure rails are parallel, and test drawer travel

A 6 x 1/2 inch pan-head Phillips screw used to fasten panels, trim, brackets and small assemblies on appliances. Replacing worn or missing screws restores secure mounting and reduces vibration or rattling. What it does:

• Fastens panels, brackets and trim where a 6 x 1/2 in. pan-head Phillips screw is required.
• Stops loose or rattling parts caused by missing, stripped or corroded screws.
• Provides the correct head profile for a Phillips driver to allow proper torque and seating.
• Used in non-structural fastening points on appliances.

• Always disconnect power and unplug the appliance before beginning repairs.
• Use the correct-size Phillips screwdriver to avoid cam-out and head damage.
• Do not over-tighten; over-torquing can strip threads or deform mating parts.
• Inspect mating threads and replace damaged components before installation.