General Electric Control Board

The defrost heater element looked good and had continuity. The defrost thermostats checked good, so that just left the Defrost Module as the likely suspect. I installed a new defrost control module and thermostats. The thermostats were inexpensive and the old ones could have been intermittent, The only "tricky" part was finding out how to get to the back screw that holds the main control panel. Discovered that the return air duct surrounding the control panel needed to come off. It helps... Read more

This was a newer GE Monogram side-by-side unit that used an inverter compressor. I removed the inverter and used an ohmmeter to measure the resistance of each of the three windings. They were all very close to one another: about 6.8 ohms per winding. I concluded that the compressor was probably not at fault. The inverter kind of burned or chemical-ish, and, when opened, showed an electrolytic capacitor had burst. I replaced the inverter with an overnight part from Amazon. It was the same... Read more

Replaced the Main Control Board Assembly along with the evaporator and condenser fan motors. I thoroughly cleaned the very very dirty condenser with a 4$ brush offered by the parts specialist and while I was at it, I changed the door seals and replaced one of the door trays. Beats the crap out of spending $10,000 on a new refrigerator that because of Covid 19 wouldn't be here before the middle of November. Thank you Matt for your help! Read more

Removed the front off the back panel, unplugged the old unit. Then using a blow dryer heated the old timer to peel the face /cover off and applied to the new clock. Plugged in the replacement clock. Replaced the front of the range. The only complaint I have is we were not informed that a new face would not be included and the old one would have to be removed and applied to the replacement clock. The face that was on the orginal clock has the buttons to set the clock and timer reversed from... Read more

Replaced the "Encoder Board". My GE Advantium control panel came of fairly easily. There was 2 screws on top to remove a vent director giving access to a single screw that held the control panel in place. Once I removed that screw, I had to slide the control panel upwards by about 1/2" before it came off. At this point, I took several photographs of the wire connections to make sure I could reassemble them correctly... there were many! After unplugging the wire harnesses and connections, I... Read more

Shut power off to unit. Took cook top out and removed metal cover to remove electrical board. Replaced with new one. Was just 5-6 connections that couldn’t be mixed up. Fairly easy fix. Works like new. Read more

After searching refrigerator videos of related problems I found AppliancePartsPros.com and inquired about replacing the Dispenser Assembly board on the front door. During the several-month malfunction period, the freezer and refrigerator were working before they finally stopped. That lead to a discussion with an APP customer rep who asked me to describe the problem and then reviewed their log of prior customer reviews & Fixit comments with me. We uncovered a description of identical issues in... Read more

Replaced timer, cleaned out exhaust and lint collectors. It's running again."Nuff said! Read more

EVERY THING WORKS, PUT IN NEW CONTROL BOARD AND WATER VALVE. VERY PLEASED. Read more

Purchased the part that I needed and it fixed the problem like a champ... Read more

I replaced the main control board kit and everthing worked like it should work. Read more

Read trouble guide then watched video Ordered part on friday,received it on monday easy install,stove works like new. ApplianceParts Pros wed was very helpfull Thankyou Read more

Easy. Opened the front panel, removed the timer, went on line with the part number. Part arrived the next day and I installed it in 2 minutes. FIXED. Read more

• Timer will not advance

Just as the folks in the comments section said, I tested everything to make sure the timer had power which it did. I then tested with the OHM tester and saw that the switch was open when the timer was set to any drying cycle. So i changed the timer and voila! timer is functioning again. It was a very easy fix. Just pop the four screws out of the back of my timer panel on the dryer, detach all the wires, lift up on the little bracket that is holding the timer in place and twist it, and it... Read more

Replace timer; remove lid switch Read more

I did an internet search - found your site explaining how to fix. I purchased the upper, middle, and lower spray arms - It took about 15 minutes total. Very very easy. No more dirty dishes! Read more