Parts for Kenmore 795.72482411 (79572482411, 795 72482411): Ice Maker Parts

The Water Filter LT800P is an OEM part for LG refrigerators. This filter is designed to remove contaminants from the water supply, ensuring clean and fresh-tasting water and ice.

Causes of a bad water filter can include extended use beyond its recommended lifespan, exposure to high levels of contaminants, or damage to the filter itself.

Symptoms of a bad Water Filter LT800P include:

• Unpleasant taste or odor in the water or ice
• Reduced water flow from the dispenser
• Indicator light signaling the need for replacement
• Visible sediment or particles in the water

This OEM LG part is also compatible with Sears/Kenmore.

The Icemaker Assembly is an OEM part for LG refrigerators. This assembly is responsible for producing ice and dispensing it into the ice bucket within the freezer compartment. It includes the ice mold, motor, and other components that work together to form, freeze, and release ice cubes efficiently.

You should replace this icemaker assembly if it becomes defective. Common causes of a bad icemaker assembly include wear and tear over time, electrical failures, or blockages in the water supply line. Mineral buildup or malfunctioning components can also hinder the ice-making process.

Symptoms of a bad icemaker assembly include:

• No ice production
• Smaller than usual or misshapen ice cubes
• Leaks or water pooling in the freezer
• Unusual noises coming from the icemaker area

This OEM LG part is also compatible with Sears/Kenmore.

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This assembly stores ice and delivers it from the ice maker to the dispenser. Replace it when the bin is cracked, warped, or its drive components are damaged, causing weak dispensing, jams, or being stuck on one ice type.

• Stores ice and interfaces with the dispenser system to deliver cubes or crushed ice
• Resolves no or weak ice dispensing
• Corrects grinding/clicking noises or auger jamming from a damaged bin
• Addresses visible cracks, broken tabs, or a bucket that won't seat securely

• Disconnect power to the refrigerator before servicing
• Open the door and pull the old bucket straight out; depress any release tab if equipped
• Align and seat the new assembly fully so the drive coupling engages—do not force it
• Restore power and test the dispenser (cube and crush selections)

The Icemaker is an OEM replacement part for LG refrigerators with built-in ice production.This component is responsible for producing and dispensing ice cubes. It functions by filling the ice mold with water, freezing it into ice cubes, and then ejecting them into the ice storage bin, ready for dispensing.

Causes of an inadequate icemaker can include scale or mineral buildup affecting internal mechanisms over several years of use. The water filter may also need replacing to keep the icemaker running smoothly.

Symptoms of an issue include:

• No ice production or slow harvesting of ice cubes  
• Jammed or improperly operating ejection mechanism
• Cavity not fully dispensing produced ice

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

This is the Home Bar cover — the molded door shelf cover that protects and conceals the refrigerator's door-in-door/home bar compartment for organized storage and a finished appearance. It restores a secure, clean barrier for items stored in the home bar. What it does:

• Replaces a cracked, chipped or missing home-bar/door-in-door shelf cover
• Keeps small bottles and items contained when the home bar is opened and closed
• Restores the proper fit and appearance of the door-in-door/home bar area
• Helps prevent items from falling out of the home bar compartment

• One Home Bar cover

• High-level replacement: usually removes and snaps into the door-in-door shelf housing; some models may require removing the inner door panel or a few fasteners
• Use basic hand tools; keep track of small screws and clips during reassembly
• Inspect surrounding clips and supports; replace any damaged fasteners for a secure fit
• For safety, close the door fully and check smooth opening/closing after install

This lower hinge assembly secures and supports the refrigerator door pivot, restoring proper door alignment and smooth opening/closing. Replace a worn or damaged lower hinge to stop sagging, help seal performance, and reduce rubbing or binding. What it does:

• Provides a stable pivot point for the lower side of the refrigerator door.
• Corrects door sagging or misalignment that can cause poor sealing or uneven gaps.
• Reduces rubbing, scraping, or binding when opening and closing the door.
• Restores proper door operation after impact damage or worn hinge components.

• One lower hinge assembly

• Disconnect power and remove food from the door area before starting; support the door to prevent dropping during removal.
• Keep all original fasteners if they are undamaged; some models may reuse screws or pins.
• Use appropriate tools and take care not to damage the door finish or gasket; wear gloves to protect hands.

The Dispenser Gasket is an OEM part for LG refrigerators. It is a seal that helps create an airtight barrier around the dispenser area, preventing air leaks and maintaining the desired temperature and humidity levels inside the refrigerator.

Causes of a bad dispenser gasket can include wear and tear over time, exposure to extreme temperatures or UV light, or physical damage from mishandling or improper installation.

Symptoms of a faulty dispenser gasket include:

• Air leaks or drafts around the dispenser area
• Condensation or frost buildup near the dispenser
• Higher than normal energy consumption due to the fridge working harder to maintain the desired temperature
• Difficulty in opening or closing the dispenser door

This OEM LG part is also compatible with some Sears/Kenmore refrigerator models

The Ice Door Handle is an OEM replacement part for LG refrigerators. It allows users to easily access ice and water from the external ice/water dispenser. Handles experience substantial daily use as people frequently obtain water/ice. Over the years, plastic hinges can degrade from repeated opening/closing stresses.

Causes include fatigue cracks along hinge points from perpetual flexing. General wear and tear as well as occasional impacts also deteriorate structure.

Symptoms of a bad ice door handle include:

• Loose, wobbly, or dysfunctional opening/closing capability
• Cracks around mounting brackets compromise integrity
• Detached handle pieces preventing access to ice/water dispenser
• Excessive opening force required or inability to fully open/close

This OEM LG replacement is also compatible with select Sears/Kenmore refrigerators.

The Ice Door Handle Roller is an OEM replacement part for LG and some Kenmore refrigerators. Each handle contains two rollers and they help the handle move smoothly and prevent any unnecessary wear and tear. Please note, this is for one (1) door handle roller. It is recommended to replace both at the same time. 

Symptoms of a bad Ice Door Handle Roller include:

• Difficulty in dispensing ice, with the chute door sticking or not opening properly.
• Noises such as squeaking or grinding when the ice door is activated.
• Increased effort needed to operate the ice dispenser handle.
• Visible wear or damage to the roller, affecting its movement.

Causes of a bad ice door handle roller can include mechanical wear from regular use, debris accumulation that impedes the roller’s movement, or damage from excessive force used on the dispenser handle.

This OEM LG part is also compatible with Sears/Kenmore models.

The Ice Bank Door Gasket is an OEM part for LG refrigerators. This gasket is designed to seal the ice bank door, ensuring a tight closure to maintain optimal temperatures inside the ice compartment. By preventing warm air from entering, it helps preserve the quality and quantity of ice produced by the icemaker.

Causes of a bad gasket can include wear and tear from frequent opening and closing of the door, physical damage from cleaning or mishandling, or degradation over time due to exposure to temperature changes.

Symptoms of a bad Ice Bank Door Gasket include:

• Ice melting or clumping in the ice compartment
• Frost buildup around the ice bank door
• Increased energy consumption
• The gasket appearing cracked, brittle, or deformed

This OEM LG part is also compatible with Sears/Kenmore.