Parts for Amana AGG222VDW6: Manifold Parts

Used for the front burner.

Used for the rear burner.

This gas pressure regulator controls the flow of natural gas or LP to the cooktop and oven valves, helping restore correct burner and oven flame performance for safe, even heating. What it does

• Regulates incoming gas pressure to the appliance's valve system so burners and oven receive consistent fuel flow
• Can correct symptoms such as burners that burn too high or too low, uneven heating, or oven temperature inconsistencies
• Works as part of the appliance's gas delivery system to maintain steady flame behavior
• Designed as a direct replacement to restore original gas flow control

• One regulator

• Turn off gas supply and electrical power before beginning service
• Inspect gas fittings and connections; use approved fittings and test for leaks after installation
• Do not modify the part; replace with the exact regulator specified for the appliance

This rear venturi tubing directs water flow and helps create the suction needed for proper drain and recirculation functions in the washer. Replacing a worn or cracked venturi restores reliable water flow and reduces leaks or siphoning issues. What it does:

• Channels water to the venturi assembly to help create suction for proper draining and recirculation
• Prevents leaks and unwanted siphoning when intact
• Helps maintain correct water flow during fill and drain cycles
• Can cause filling/draining problems or gurgling noises when cracked or clogged

• Disconnect power and turn off water supply before starting any repair
• Access may require removing the washer cabinet or rear panel; follow your service manual
• Inspect clamps and adjacent hoses; replace clamps if corroded or damaged
• Replace with this OEM venturi tubing for best fit

This front burner gas tube routes natural gas from the manifold to a front surface burner on compatible gas ranges for a stable flame and dependable ignition. Replace if kinked, corroded, or leaking.

• Directs natural gas from the manifold to a front cooktop burner
• Helps maintain proper flow for consistent flame height and reliable ignition
• Restores performance when the original tube is blocked, bent, or damaged
• Common symptoms: front burner won't light, weak/uneven flame, gas odor, visible cracks or kinks

• Shut off gas supply and power; allow the appliance to cool before servicing
• Support fittings with two wrenches; avoid overtightening and do not kink the tube
• Transfer any reusable orifices/seals from the original if applicable; replace damaged seals
• After installation, restore gas and check all joints for leaks with a soap-and-water solution

Restore reliable heating with this oven burner assembly. It channels gas through calibrated ports to produce a stable, even flame across the burner, promoting consistent ignition and uniform oven temperatures when baking. What it does:

• Directs gas from the oven valve and provides the flame path for heating
• Works with the igniter to light the oven flame
• Helps maintain even heat distribution throughout the oven
• Typical symptoms of a failed burner: delayed or no ignition, weak/uneven flame, sooting, popping on ignition, or slow/uneven preheating

• 1 oven burner assembly

• Disconnect power and shut off the gas supply; allow the oven to cool completely
• Remove oven racks and the oven bottom panel to access the burner
• Note igniter alignment and transfer any reusable mounting hardware from the original burner
• Restore gas/power, check all connections for leaks, and verify a steady, properly aligned flame

Factory replacement screw that secures appliance components and hardware. Use it to replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and help prevent loosening or damage from vibration.

• Fastens brackets, panels, or internal parts at the original mounting points
• Replaces worn or missing hardware to correct loose or misaligned components
• Helps reduce vibration-related noise and movement
• Matches the original thread and length specified for the application

• Disconnect power; shut off water or gas if applicable before servicing
• Compare to the original for thread and length match before installation
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any original spacers/washers if present; replace if damaged

This gas valve assembly controls gas flow to a cooktop or oven burner, restoring proper ignition and temperature control for safe cooking. Replaces a failed or leaky valve to help appliances light and operate correctly. What it does:

• Regulates gas flow to a single burner or oven gas circuit
• Stops gas flow when control is off to prevent leaks
• Can cause burners or oven to not light, not heat, or to cut out when faulty
• Helps eliminate clicking/ignition issues when valve operation is restored

• One gas valve assembly

• Turn off gas supply and electrical power before servicing
• Inspect gas fittings and use a leak test after installation
• Do not attempt installation if you are not comfortable working with gas appliances

This is a replacement screw used to secure panels, trim, or small components on compatible Whirlpool appliances. Installing the correct fastener restores proper fit and helps stop rattles or loose trim. What it does:

• Secures trim, panels, or control components to prevent movement and rattling
• Replaces missing or damaged hardware that can cause gaps or loose parts
• Helps maintain proper alignment of panels and movement-free operation
• Used wherever a factory screw of this size and head style is specified

• Always disconnect power (and water, if applicable) before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Install by hand until threads engage, then tighten snugly—do not overtighten
• Keep removed hardware organized before final reassembly

The Thrmst-fix is an OEM component compatible with Whirlpool ranges. It serves as the module responsible for heating cooking surfaces like stovetop burners or bake/broil elements. 

Symptoms of a faulty Thrmst-fix can include:

• Inconsistent or uneven heating between surface areas  
• Burners or elements taking longer than normal to reach temperatures
• Intermittent or surging control issues when adjusting temperatures
• Hotspots or cool spots on cooking surfaces that won't regulate  

Causes may stem from normal wear over extended and frequent use of heating elements. Mineral buildup affecting electrical connections could cause control or regulation issues as well.

This OEM replacement part works with Maytag, KitchenAid, Jenn-Air, and select Kenmore electric range models too. 

Natural gas.

Replacement burner orifice (1.25) that controls gas flow to the burner for proper flame and cooking performance. Use when an orifice is clogged, damaged, or the wrong size for correct burner output. What it does:

• Regulates gas flow to the burner so the flame burns steadily and the cooktop reaches expected heat.
• Helps correct weak, uneven, or sooty flames and inconsistent burner heating when the orifice is the cause.
• Restores proper burner output after clogging, corrosion, or damage from wear or debris.

• Turn off the appliance power and shut off the gas supply before replacing.
• Verify the orifice size required for your fuel type and appliance before installation; do not file or modify the part.
• Tighten securely but avoid overtightening; check all connections for leaks after installation using an approved leak-detection method.
• If you smell gas or suspect a leak, turn off the gas immediately.

The Clip is an OEM part for Whirlpool ranges. This part holds the surface igniter in place, ensuring that it remains properly positioned to ignite the gas burner efficiently.  

Causes of a bad surface igniter clip can include wear and tear from regular use, damage from high heat exposure, or breakage due to improper handling during maintenance. 

Symptoms of a bad surface igniter clip include:

• The igniter not staying in place
• Difficulty in lighting the burner
• The burner not igniting at all
• Visible damage or deformation of the clip

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black. For biscuit order 98008169. For white order WP98008544.

This appliance screw secures panels, brackets, and internal components. Replacing a stripped or missing screw keeps parts tight and aligned, reducing vibration and preventing noise for reliable day-to-day operation.

• Secures mounting points for panels, brackets, or assemblies
• Replaces stripped, rusted, or missing hardware to restore a solid attachment
• Helps reduce rattling, vibration, and misalignment from loose fasteners
• Maintains proper fit so components operate as intended

• Disconnect power; turn off water or gas before service
• Match the screw to its original location and replace one at a time
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver type/size specified for your model

This surface burner spark electrode creates the electrical arc that lights the gas at your cooktop/range burner. Replace a cracked or fouled electrode to restore quick, reliable ignition on the affected burner and reduce repeated clicking.

• Generates the high-voltage spark that ignites surface-burner gas
• Promotes fast, consistent ignition and stable flame startup
• Common symptoms: burner won't light, lights intermittently, or sparks weakly at one burner while others work
• Visual clues: cracked porcelain insulator, bent tip, or heavy buildup on the electrode

• Disconnect power and shut off gas supply before servicing
• Remove grate, cap, and burner head to access the electrode
• Transfer mounting hardware from the old electrode
• Route and reconnect the lead securely; keep it away from heat and sharp edges, then test for proper spark before reassembly

The Surface Burner Ignitor is an OEM part for Whirlpool gas ranges. This part ignites the gas to create a flame on the burner, allowing for efficient cooking.

Causes of a bad ignitor can include wear and tear from regular use, electrical issues, or physical damage to the ignitor element.

Symptoms of a bad surface burner ignitor include:

• The burner not lighting or taking longer to light
• Clicking sounds without ignition
• Weak or inconsistent flame
• The smell of gas without ignition

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.