Parts for Frigidaire FLCG7522AW0: Motor / Tub Parts

Replace a broken or missing washer agitator cap that leaves the top of your agitator shaft exposed. Simple snap-on installation takes just minutes.

Washer won't spin or agitate? A faulty motor assembly stops drum movement during wash cycles. This part powers agitation and spin functions in washers.

Single replacement screw for laundry center panels, brackets, and trim. Restores secure fit when original fastener is missing, stripped, or damaged.

Fix a washer that won't agitate or clean clothes properly. This agitator restores wash action when splines strip or the part cracks. DIY install.

If your washer won't agitate or spin properly, the transmission may have failed. This mechanical component engages the drum during wash and spin cycles.

Washer won't spin or clothes stay sopping wet? The actuator motor shifts between wash and spin cycles. Moderately difficult repair for DIYers.

Fix excessive shaking and banging in your washer with this suspension spring. Replaces worn or broken springs. Moderate difficulty, replace all four.

Fix excessive shaking, banging, or off-balance errors caused by a broken suspension rod. This tub stabilizer absorbs movement during spin cycles.

Top cap for tub suspension rod assembly in washer dryer combos. Replace when cracked, broken, or missing to properly secure suspension system.

Hose assembly for laundry center units. Connects water supply or drainage components. Replace if cracked, leaking, kinked, or worn to restore proper function.

Replacement mounting screw for laundry center panels and components. Needed when original screw is stripped, missing, or damaged during repair work.

Drive hub for washer dryer combo units. Connects the motor to the drum transmission system. Replace if cracked, stripped, or worn to restore proper operation.

Motor won't start on your washer dryer combo? A faulty start capacitor prevents the drum from turning. This part provides the electrical boost needed.

Mounting screw for laundry center and washer dryer combo units. Replaces lost, stripped, or damaged screws that secure panels and components during installation.

Fix rattling noises or loose components with this retaining ring. Secures internal parts to prevent shifting during operation. Simple 10-minute repair.

Outer drum cover that installs around the wash basket. Replace this cosmetic panel when cracked, damaged, or worn to restore a clean appearance.

Washer shaking excessively or stopping mid-cycle? This off-balance switch detects vibrations and stops the spin cycle to prevent damage. Easy DIY fix.

Protection panel for laundry center units. Shields internal components from damage. Replace if cracked, broken, or missing to restore proper coverage.

Replacement mounting screw for laundry center panels and brackets. Needed when original screws are missing, stripped, or corroded to secure components.

Fix clothes not spinning dry or tub wobbling issues with this laundry center spin tub. Replaces worn or damaged inner basket in washer dryer combos.

Fix a washer that stops mid-cycle or shakes excessively with this out of balance switch bracket. Detects drum vibrations during spin cycle. DIY repair.

If your washer won't complete cycles with heavy loads or constantly drains, the pressure sensor may be faulty. Monitors water levels for proper fills.

Pulley assembly powers tub rotation during wash cycles. Replace if worn from use, damaged by broken belts, or rusted from water exposure. Confirm fit.

Connects your washer tub to household plumbing to drain water after each cycle. Replace if cracked, kinked, leaking, or too short for your installation.

Secures hoses and wiring in your washer dryer combo to prevent rubbing, leaks, and noise. Replace when clips break or lines come loose. Confirm fit.

Fix a washer that won't spin or agitate with this laundry center drive belt. Connects motor to drum for spinning and washing. Moderate DIY repair.

Flat metal washer that distributes load from nuts or bolts in your laundry center assembly. Replace if worn, missing, or damaged to maintain proper fastener seating and prevent loosening over time.

Fix excessive vibration or a loose motor with this washer motor mounting nut. Secures the motor assembly for stable operation during wash cycles.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Flat washer that spaces and secures fasteners in your laundry center assembly. Replace if worn, missing, or causing loose connections between parts.

Replacement mounting screw for laundry center panels and components. Restores secure fit when original fastener is stripped, lost, or damaged.

Replace your laundry center's drain pump seal to prevent water leaks and restore proper drainage. Install when cracked or worn to maintain a tight barrier.

Washer not draining or water remains in tub? This drain pump assembly removes water between cycles. DIY repair typically takes 30 minutes to install.

Tub ring that secures and seals between the outer tub and basket assembly. Replace if cracked, broken, or worn to restore proper tub alignment.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Fix intermittent operation or complete failure in your laundry center. This control-to-component wiring harness restores electrical connections to fans and systems.