Parts for Frigidaire GLGT1031FS3: 11 - Motor / Tub Parts

Replaces a cracked or broken splash tub cover assembly on your washer. Installs around the tub to protect internal components from water damage.

Washer won't spin or drain? This capacitor shield assembly protects wiring and controls while housing the start capacitor for proper motor operation.

Connects your washing machine to the household water supply. Replace this flexible inlet hose if cracked, leaking, or worn to restore proper flow.

Rubber washer that seals the connection between your washing machine's inlet hose and faucet. Replace if cracked, worn, or causing leaks at connection.

Secures the blower wheel to the motor shaft in your dryer. Replace if worn, loose, or causing rattling noises to restore proper airflow. Verify fit by model.

Includes ATC

This replacement upper agitator restores the washer's normal wash action by moving clothes and improving water circulation for better cleaning. It fits the factory agitator location and replaces worn, cracked, or damaged agitators to restore performance. What it does:

• Rotates during the wash cycle to move garments through the water for more effective cleaning
• Promotes water flow and prevents clothes from bunching or tangling
• Replaces a cracked, broken, or excessively worn agitator that causes poor wash results
• Helps reduce unusual noise or vibration caused by a damaged agitator

• One upper agitator

• Disconnect power and water supply before beginning any repair
• Remove the agitator cap/cover and securement (bolt or clip) to lift out the old agitator
• Install hardware to manufacturer torque recommendations
• Run a short test cycle with a small load to check for leaks or vibration

Replacement mounting screw for washers and laundry centers. Secures panels, components, or brackets. Replace if lost, stripped, or corroded.

Fix leaking or noisy washer drums caused by broken trunnion bolts. This fastener secures the trunnion assembly to prevent water leaks and vibration.

Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.

The trunnion is the hub that mounts the washer's inner tub to the drive shaft. Replacing a worn hub restores a solid, centered connection so the basket spins smoothly without wobble, slip, or grinding. What it does:

• Secures and centers the spin basket on the drive shaft for balanced rotation
• Transfers drive torque to the inner tub during spin
• Helps maintain basket alignment to reduce vibration
• Typical symptoms of failure: loose/wobbly tub, scraping or grinding noises, poor or no spin, frequent out-of-balance events

• 1 trunnion

• Disconnect power and water before service; wear gloves and eye protection
• Access the hub by removing top/access parts, then the agitator/wash plate and inner-tub fasteners
• Clean the shaft and mating surfaces; seat the new trunnion fully and tighten fasteners evenly in a crisscross pattern
• Inspect related parts (tub seal, bolts, bearing) while open and replace if worn; run a short test cycle to ensure smooth spin

Replacement mounting screw that secures panels, brackets, and trim pieces on your washer. Needed when original fasteners are missing, stripped, or damaged.

Fix loud whirling noise during spin cycle with this washer spin bearing washer. Supports the belt pulley bearing for smooth rotation. Video available.

Return spring for washer door lock mechanism. Restores tension so the latch returns to proper position. Replace if worn, missing, or causing loose latch.

Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.

Enables smooth drum rotation in your washer. Replace if you hear loud roaring or whirling noises during spin cycle. Confirm fit with your model number.

Secures the main pulley to the transmission shaft in your washer. Replace if the screw is missing, stripped, or loose to prevent pulley slippage.

Drive belt connects motor to drum for wash and spin cycles. Replace if washer won't spin, clothes stay wet, or you smell burning rubber. Verify fit.

The Idler Pulley is an OEM part for Frigidaire dryers. It helps guide and maintain tension on the dryer drum belt, ensuring the drum rotates smoothly during the drying cycle.

Over time, the idler pulley can wear out due to friction and regular use, or it may become damaged from excessive strain or misalignment. If the idler pulley fails, the dryer drum may not rotate properly, leading to inefficient drying or a complete inability to dry clothes.

Symptoms of a bad Idler Pulley include:

• Squeaking or squealing noises during operation
• The drum not rotating or rotating unevenly
• The belt appearing loose or slipping off the drum

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Secures shafts and components to prevent axial movement, wobble, and noise. Replace if worn, damaged, or loose to restore proper alignment. Confirm fit.

Mounting screw hardware kit for washers and laundry centers. Replaces lost, stripped, or corroded screws, nuts, and washers used to secure panels.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Washer won't spin or agitate? Humming motor or clothes staying wet often means a failed drive motor. This repair typically takes 15-60 minutes with basic tools.

Molded protective shield covers internal wiring and terminals from heat, moisture, and debris. Replace if cracked, broken, or missing to protect components.

Washer won't drain or spin? A clogged or failed drain pump is the likely cause. This part removes water from the tub between cycles. DIY repair in 15-30 minutes.

Replacement drain hose directs used water from your washer to the household drain. Needed when original hose is cracked, split, or leaking.

Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.

Hex washer head screw for laundry centers. Secures panels and components during assembly. Replace if stripped, missing, or damaged during repairs.

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

Color: white. It measures about 3-1/2 inches in diameter, and 2-1/2 inches high.

Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.

Replacement mounting screw for laundry center panels and components. Secures parts firmly in place. Order this screw if original is stripped or missing.

Secures the drum baffle (lifter vane) to your washer drum. Replace missing, stripped, or loose screws to keep baffles firmly attached and prevent rattling.

Secures and seals your washer's drain hose connection to prevent leaks. Replace if cracked, brittle, or leaking. Confirm fit with your model number.

Ratchet-style fastener secures panels and components in washer dryer combos. Replace if broken, missing, or worn to restore secure fastening.

Cushion bumper for washer dryer combo units. Installs to absorb vibration and reduce noise. Replace if cracked, worn, or missing for proper support.

Secures trim, panels, and wiring harnesses in your laundry center to prevent rattling and shifting. Replace when clips crack or lose tension. Confirm fit with your model number.

Secures interior trim and components in your laundry center to prevent rattling and shifting. Replace when worn or broken to restore a snug fit. Verify compatibility with your model number.

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Snap-in bushing for washer assemblies. Replaces worn, cracked, or missing bushings that provide cushioning and support in internal components.

Vertical spring adjuster insert.

Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.