Parts for Lg LDG4311ST/00: Other Parts

This gas surface burner head restores even flame and reliable lighting on your range cooktop. Replacing a worn or clogged burner helps bring back proper ignition, flame pattern, and consistent heat output. What it does:

• Directs gas from the orifice through precisely formed ports to create an even ring of flame
• Works with the spark igniter for quick, consistent ignition
• Helps maintain correct flame size and color for efficient cooking
• Typical symptoms include: burner won't light, delayed ignition, weak/uneven flame, or yellow-tipped flames

• Includes 1 burner head

• Disconnect power and shut off the gas supply before servicing
• Remove grate and burner cap; lift off the old burner head and clean the mating surface
• Align the new burner head over the orifice and ensure proper clearance to the igniter
• Reassemble, restore gas/power, and test burner operation and flame pattern

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This insulator cushions and isolates a component to reduce vibration and help prevent heat or electrical transfer to adjacent parts. It's a simple replacement part that restores proper spacing and support where the original insulator has worn or failed. What it does

• Provides cushioning and vibration isolation for the mounted component
• Helps maintain correct spacing and alignment of panels or assemblies
• Reduces direct heat or electrical contact between parts
• Stops rubbing or noise caused by a deteriorated or missing insulator

• One insulator

• Turn off power and unplug the appliance before attempting any repair
• Remove any surrounding panels or components as needed to access the mount point
• Replace only the damaged insulator with the same shape and orientation; ensure a snug fit
• If fasteners or clips were removed, reuse OEM hardware or replace with equivalent parts to secure the insulator

This insulator is a small protective cushion that helps damp vibration and prevent rubbing or heat transfer between adjacent appliance components. It restores proper spacing and reduces noise where panels or parts meet. What it does:

• Cushions components to reduce vibration, rattling, and wear
• Prevents metal-to-metal contact that can cause noise or damage
• Helps maintain correct spacing and alignment of nearby parts
• Can reduce heat transfer between hot and sensitive parts

• One insulator

• Disconnect power before servicing the appliance
• Remove only the panels or components necessary to access the old insulator
• Press or adhesive-mount the replacement in the same location and orientation as the original

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

This burner tube directs gas from the valve to the oven's burner assembly for proper flame distribution and heat during baking and broiling. Replacing a damaged tube restores safe, even combustion and consistent cooking performance. What it does

• Channels gas to the oven burner so the flame lights and stays steady
• Helps maintain even heat for reliable cooking and browning
• Prevents gas leaks caused by cracks, holes or severe corrosion
• Can resolve symptoms like weak or uneven flames, flame blowouts, or visible tube damage

• Turn off gas supply and electrical power before beginning any service.
• Inspect mounting hardware, gaskets and alignment; replace any worn seals to ensure a proper fit.
• Do not force, bend, or dent the tube during installation; handle carefully to avoid leaks.

This replacement screw fastens panels and components in your appliance, keeping them secure and aligned. Replace stripped, rusted, or missing hardware to stop rattles and ensure assemblies stay tight through everyday use.

• Secures covers, brackets, and internal assemblies at the specified mounting points
• Helps correct looseness or misalignment after a fastener is lost or stripped
• Can reduce rattling or vibration noises caused by loose fasteners
• Restores proper fit of panels or trim pieces

• Disconnect power to the appliance and shut off water or gas before servicing
• Match length and thread to the original fastener before installation
• Start threads by hand to avoid cross-threading; tighten only until snug to prevent damage
• Reuse any washers, spacers, or threadlocker originally installed at this location

This flat hardware washer helps secure bolts and fasteners in the washer assembly to keep panels and components seated and stable. Simple replacement can restore proper clamping and reduce movement around joints. What it does:

• Provides a smooth bearing surface under nuts or bolt heads to distribute load
• Prevents fasteners from loosening due to vibration or movement
• Helps maintain proper alignment of panels and small components
• Worn, corroded, or missing washers can cause loose panels, increased noise, or premature fastener wear

• Replace with the same type and size washer removed from the appliance
• Use basic hand tools; support the assembly to avoid stress on other components
• If corrosion or thread damage is present, replace the bolt/nut as well
• Disconnect power and follow manufacturer safety guidance before servicing

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This control board assembly directs power and communication to key components, interpreting inputs and sensor signals so the appliance runs the correct functions and cycles. Replaces a failed electronics module to restore reliable operation.

• Distributes power and control signals to major components per the unit's programmed logic
• Interfaces with sensors and the user controls to execute selected functions
• Coordinates cycle timing and safety monitoring
• Common signs of failure: no power or won't start, unresponsive controls/display, intermittent operation, error codes, or unexpected shutdowns

• Disconnect power to the appliance before servicing
• Handle the board by the edges; use ESD protection to avoid static damage
• Photograph and label connectors, then transfer them one at a time to the new board
• Secure wiring to avoid pinching; follow the unit's tech sheet or service manual

This tapping screw secures appliance panels, brackets, and trim. Replace a missing or stripped fastener to restore a tight, rattle-free fit and keep components properly aligned.

• Cuts its own threads as it drives (self-tapping) to fasten metal or plastic components securely
• Helps eliminate looseness and vibration noises when an original screw is missing or damaged
• Typical signs you need this part: loose or rattling panels, gaps/misalignment, or covers that won't stay secured
• Direct replacement for the original fastener in the same location

• Disconnect power; turn off water or gas supplies before service
• Start the screw by hand to avoid cross-threading, then tighten with the correct driver
• Align parts fully before tightening and avoid overtightening, especially into plastic
• Reuse any original washers or clips that were installed with the screw

This customized screw is the exact fastener specified by the manufacturer to secure components in select LG appliances. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps maintain proper alignment over time.

• Secures panels, brackets, and internal assemblies at original mounting points
• Helps reduce vibration and rattling noises from loose hardware
• Replaces missing, rusted, or stripped screws
• Supports stable operation by keeping parts firmly in place

• Disconnect power; shut off water or gas before service
• Match the screw to the exact location using your model's parts diagram
• Start threads by hand; tighten snugly without overtightening to avoid stripping
• Use the correct driver bit for the head style to prevent damage

This heater cover is the replacement housing that protects the dryer heater assembly and helps direct airflow for reliable drying performance. It restores proper heater positioning and helps prevent contact with heating components. What it does:

• Protects the heater assembly and surrounding components from debris and direct contact
• Helps channel airflow through the heater area for consistent drying
• Can reduce rattling or noise caused by a damaged or loose heater cover
• May be replaced when cover is cracked, warped, or missing fasteners

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury
• Inspect mounting tabs and fasteners; replace any damaged clips or screws for secure fit
• Minor disassembly of the dryer cabinet may be required; keep track of removed screws and panels
• If you smell burning or see damaged wiring, stop.

This heater cover protects the dryer heater assembly and helps direct airflow for proper heating performance. It replaces a cracked or damaged cover to restore safe operation and part alignment. What it does:

• Shields the heating element and internal components from debris and accidental contact
• Helps channel airflow through the heater for efficient drying
• Can prevent rattling or vibration caused by a loose or broken cover
• Common symptom: damaged cover may be noticed when replacing the heater or after impact/overheating

• Disconnect power before accessing the heater assembly; allow components to cool fully
• Follow the appliance service manual for disassembly/reassembly and use correct fasteners
• Inspect adjacent components (heater element, terminals, mounting clips) and replace if damaged

The Nozzle is an OEM part for LG ranges. It is a small component located inside the burner box that emits gas to create flame. During operation, the nozzle precisely meters fuel flow to each burner to achieve balanced and consistent heating. 

Symptoms of a faulty nozzle include: 

• Burners that light unevenly or emit an irregular flame pattern
• Inability to adjust burner flames or in some cases, lack of ignition
• Possible safety hazard from gas emissions not mixing or igniting properly

Causes can stem from mineral buildup clogging the narrow opening over time. Damage, such as nicks or corrosion, may also disrupt critical gas flow.

This OEM LG part is also compatible with some Kenmore ranges featuring LG gas cooktop systems. Replacing a worn nozzle restores optimal and safe burner performance.

The Nozzle is an OEM part for LG ranges. It is a small component located inside the burner box that emits gas to create flame. During operation, the nozzle precisely meters fuel flow to each burner to achieve balanced and consistent heating. 

Symptoms of a faulty nozzle include: 

• Burners that light unevenly or emit an irregular flame pattern
• Inability to adjust burner flames or in some cases, lack of ignition
• Possible safety hazard from gas emissions not mixing or igniting properly

Causes can stem from mineral buildup clogging the narrow opening over time. Damage, such as nicks or corrosion, may also disrupt critical gas flow.

This OEM LG part is also compatible with some Kenmore ranges featuring LG gas cooktop systems. Replacing a worn nozzle restores optimal and safe burner performance.

This replacement outer housing case provides a durable protective cover for internal components, restoring the appliance's exterior fit and protection. It helps maintain proper component alignment and prevents dirt and moisture from entering sensitive areas. What it does:

• Protects internal components and wiring from damage, dust, and moisture.
• Restores proper alignment and secure mounting for controls or assemblies attached to the case.
• Reduces rattles, vibration noise, or loose-feeling panels caused by cracked or warped housing.
• Helps prevent minor water intrusion into internal compartments when the original case is damaged.

• One replacement outer housing case

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Installation typically requires basic tools (screwdriver set); keep fasteners and trim in a safe place during removal.
• Handle the replacement carefully to avoid scratching or cracking the new case; ensure all clips and screw locations line up before final fastening.
• If seals, gaskets, or attached trim were removed, inspect and replace as needed for proper reassembly.

This vent assembly is the dryer exhaust duct that channels hot, moist air from the dryer to the home's venting system, helping the appliance dry clothes efficiently and safely. What it does:

• Directs dryer exhaust from the cabinet to the external vent
• Helps prevent lint buildup in the cabinet and duct path
• Supports proper airflow to reduce drying times and overheating risk
• Can help stop symptoms like poor drying, longer cycles, or a hot dryer cabinet

• Vent assembly

• Disconnect power (and gas, if applicable) before starting any work
• Access typically requires removing the dryer's rear or front access panel
• Inspect and clean the vent path and surrounding seals before installing the new assembly

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

The Oven Ignitor is an OEM replacement part for LG ovens. It is a critical component responsible for igniting the gas burners or heating elements within the oven, allowing it to reach and maintain the desired cooking temperatures.

Symptoms of a bad oven ignitor include:

• Failure of the oven to ignite or heat up properly
• Intermittent or delayed ignition issues
• Clicking or sparking noises from the ignitor area

Causes of an oven ignitor failure can range from general wear and tear over time, to electrical or mechanical malfunctions, to obstructions or buildup preventing proper ignition.
 
This OEM LG part is also compatible with Sears/Kenmore models.

This replacement nozzle holder secures the appliance's nozzle in place so sprays and steam stay directed where needed, restoring correct alignment and stable operation. It's a simple wear-and-tear part that keeps the nozzle from wobbling or falling out. What it does:

• Secures and positions the spray/steam nozzle so fluid or steam is delivered correctly
• Keeps the nozzle from shifting, slipping, or vibrating during use
• Prevents nozzle from detaching and reduces the risk of misdirected spray
• Helps restore normal operation when a broken or worn holder causes loose nozzle movement

• Disconnect power and water before servicing to avoid shock or scald risk
• Access may require removing exterior trim or panels—keep fasteners organized
• Install by snapping into place or fastening with the original screws as shown in the OEM diagram
• Replace only with the exact OEM part number to ensure fit and function

This burner assembly replaces a damaged or worn surface burner to restore proper heat output and stable flame control on compatible gas ranges. It fits into the cooktop and connects to the burner valve and ignition system for normal operation. What it does:

• Provides the main burner head and ports to produce a stable gas flame for cooking
• Restores even heat spread when a burner is clogged, corroded, or physically damaged
• Helps resolve ignition problems caused by a broken or misaligned burner head
• Supports proper flame shape to improve simmer and boil performance

• Turn off the gas supply and power to the appliance before attempting any work
• Remove the cooktop or burner grate per the service manual to access the assembly
• Check all connections and test for gas leaks after installation

This burner assembly replaces the damaged or worn cooktop burner to restore even heating and safe operation on compatible LG ranges. It provides the complete burner unit that mounts under the cooktop surface for reliable ignition and heat transfer. What it does:

• Houses the burner element and delivers heat to the cookware for range cooking
• Replaces cracked or non-heating burners that cause uneven cooking or no heat
• Restores proper fit and alignment for consistent ignition and flame/element performance
• Helps eliminate clicking, sputtering, or intermittent heating when the burner is the confirmed fault

• Disconnect power and shut off gas before servicing; follow all safety precautions
• Handle glass or porcelain cooktop surfaces carefully to avoid chipping during removal/installation
• Tighten mounting fasteners securely and test operation after installation

This door frame replaces the outer trim that surrounds the appliance door, restoring a finished look and helping keep the door seal properly aligned. It's a direct-fit exterior trim piece for compatible LG doors. What it does:

• Replaces damaged, cracked, or warped outer door trim to improve appearance and edge alignment
• Helps maintain proper door closure by supporting the door perimeter
• Prevents drafts and reduces risk of further cosmetic damage at the door edge
• Matches OEM fit and mounting points for a secure install

• Disconnect power to the appliance before beginning any work
• Remove the door or inner trim panels only as required to access mounting screws; keep fasteners organized
• Use appropriate hand tools (screwdriver, nut driver) and avoid over-tightening to prevent cracking the trim
• Handle the part carefully to avoid scratching the finish; verify fit and alignment before final reassembly

This is the clear glass pane in the microwave door that provides a viewing window into the cavity. Replace a cracked or cloudy window to restore visibility and help the door assembly fit and look like new.

• Forms the transparent viewing pane in the microwave door
• Replace when the glass is cracked, chipped, shattered, loose, or rattling
• Helps maintain correct door assembly when reinstalled with the factory frames
• Restores clear visibility if the window has become hazy or scratched

• Disconnect power at the breaker or unplug the appliance before servicing
• Support the door; removal may be required—work on a padded surface
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Reassemble door layers in the original order and verify latch alignment before use

This air guide directs cooled air inside the refrigerator compartment to help maintain even airflow and temperature distribution. Replaces a damaged or missing guide to restore proper venting and help reduce uneven cooling. What it does

• Channels cold air from the evaporator vent into the fresh food compartment for more consistent cooling.
• Helps reduce warm spots or uneven temperatures near shelves and door bins.
• Prevents direct airflow onto stored items, protecting sensitive foods from frost or drying.
• Fits behind vents or above crisper drawers to guide airflow where needed.

• One (1) air guide

• Always unplug the appliance or switch off power at the breaker before servicing.
• Typically installs without specialty tools; you may need to remove shelves or drawers for access.
• Handle plastic parts carefully to avoid cracking; align tabs and snap into place until secure.
• If airflow issues persist after replacement, check vents, damper, and evaporator fan for related faults.

This Cover Assembly, Poise is the trim piece that snaps over the hinge/closer area, shielding the mechanism and wiring while giving your appliance a clean, finished look. Replace a cracked or missing cover to restore proper protection and appearance.

• Conceals and protects the hinge/closer mechanism and any routed wiring
• Helps keep debris out of moving parts to support smooth door motion
• Restores a clean, finished appearance when the original cover is damaged or missing
• Common signs: cracked plastic, broken tabs, loose/missing cover, exposed hinge area

• Disconnect power before servicing
• Support the door to avoid stressing hinges while removing/installing the cover
• Remove screws or release tabs to take off the old cover; align and secure the new cover
• The door opens and closes freely with no interference

This handle supporter is the bracket that anchors the door handle to the appliance door, keeping the handle secure and aligned. Replacing a cracked or stripped supporter restores a solid, dependable grip on the door.

• Secures the handle to the door and maintains proper alignment
• Helps fix a loose, wobbly, or detached handle
• Replaces a broken or worn mounting bracket that won't hold screws

• Disconnect power and, if applicable, shut off water before service
• Remove the handle and any trim to access the supporter and mounting screws
• Transfer or replace screws as required; do not overtighten into plastic
• Verify handle alignment and operation before fully reassembling

Color: Stainless Panel with Black Glass

The inner cover protects internal components and wiring by covering the appliance's cabinet opening, helping prevent debris entry and accidental contact. It restores safe access and maintains the appliance's internal layout and airflow. What it does

• Shields internal electronics, wiring and assemblies from dust and debris
• Helps prevent accidental contact with energized components
• Restores proper internal clearance and part alignment after repair
• Can address symptoms like visible damage, exposed wiring, burning odor or intermittent operation caused by a compromised cover

• Replace with power disconnected and appliance unplugged to avoid shock
• Verify correct orientation and secure all mounting tabs/screws; do not force into place
• Inspect adjacent wiring and components for damage while the cover is removed
• Use only the part number shown for exact fit

This hinge assembly secures and lets a refrigerator or freezer door pivot smoothly, restoring proper door alignment and seal for better cooling and operation. Replaces worn, bent, or broken hinge hardware to reduce drifting or rubbing doors. What it does:

• Provides the pivot point that lets the door open and close smoothly
• Restores correct door alignment to help the gasket seal properly
• Stops door sagging, binding, or uneven gaps that can cause cold loss
• Works with the cabinet and door mounting points to maintain consistent operation

• Use basic hand tools; support the door during removal to prevent damage or injury
• Disconnect power to the appliance before making repairs when working near electrical components
• Follow OEM instructions for torque and fastener placement to ensure correct alignment

The Display Cover is an OEM part for LG ranges. It covers and shields the control panel display located at the top of the range. This protective cover helps prevent damage from spills, splatters, and accumulated grease and grime that could compromise visibility and functionality over time.

Causes of a bad display cover include normal wear and tear from repeated cleaning, exposure to heat and cooking vapors, or accidental damage from impact.

Symptoms of a bad display cover may include:

• Cracks or clouding of the plastic material
• Missing mounting screws or clips
• Grease or grime build-up that cannot be fully cleaned
• A cover that is loose, warped or no longer fully seals the display

This OEM LG part is also compatible with some Kenmore models.

This single wiring harness connects appliance components to route power and signals reliably, restoring electrical continuity for normal operation. It's a direct-fit replacement when the original harness is damaged or corroded. What it does:

• Carries power and control signals between components so circuits complete and controls respond
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or loss of function
• Helps stop shorts, arcing, or connector-related failures when the original harness is compromised
• Matches OEM connector types and pin arrangements for an accurate replacement

• Disconnect power (unplug appliance or switch off breaker) before beginning any work
• Handle connectors gently; avoid pulling on wires—release locking tabs first
• Route and secure the harness away from hot surfaces and moving parts to prevent wear

This single wiring harness routes electrical power and signals between components to restore proper connections and reliable operation. It replaces a damaged or worn harness to help eliminate intermittent power or control issues. What it does:

• Transfers power and control signals between appliance components to maintain proper function
• Replaces frayed, burnt, or damaged wiring that can cause intermittent operation or component failure
• Helps resolve symptoms like loss of power to a module, erratic behavior, or failure to respond
• Provides a direct plug-and-play connection when matching the correct factory harness

• Disconnect all power (unplug or switch off circuit breaker) before starting any work
• Handle connectors gently and seat firmly until they click into place

This is a single wiring harness that routes power and signals between appliance components to restore reliable electrical connections. It replaces a damaged or worn harness so controls and features can communicate properly. What it does:

• Carries power and control signals between specific components
• Restores interrupted circuits that can cause intermittent operation or component failures
• Helps resolve symptoms like no power to a component, inconsistent function, or error codes tied to open/shorted wiring
• Provides factory-style connectors for a direct fit and reliable connections

• Disconnect power (unplug or turn off breaker) before installing to avoid shock or damage
• Inspect connectors and routing, match connector types and wire colors before connecting
• Avoid pinching or sharply bending wires; secure harness using existing clips or ties

The Supporter, PCB Range is an OEM component specifically designed for LG ranges. This part supports and protects the Printed Circuit Board (PCB) which controls many of the range's electronic functions. 

Over time, the plastic housing and clips that make up the PCB Supporter can weaken or become brittle due to heat exposure inside the oven. This repeated heating and cooling can cause cracks or breaks which compromise the protection of the circuit board. 

Symptoms of a bad PCB Supporter include:

• Exposed or loose PCB that is at risk for impact damage  
• The circuit board that does not seat properly or makes poor contact
• Intermittent or unpredictable function of electronic controls

This OEM LG part is also compatible with Sears/Kenmore ranges. 

This control knob replaces a worn or broken knob on your range or cooktop, restoring smooth, accurate control of the burner. It fits onto the valve stem so you can select heat settings with proper alignment and feel.

• Turns the burner valve stem to choose OFF/LOW/HIGH and intermediate settings
• Replaces cracked, stripped, loose, or missing knobs
• Restores proper alignment and positive engagement when turning
• Symptoms include wobbling, spinning without engaging, or difficulty adjusting heat

• Disconnect power and shut off gas supply before servicing
• Pull the old knob straight off the valve stem; align the new knob with the stem flat and press straight on until fully seated
• Do not pry on or twist the valve stem; avoid using tools on the stem
• After installation, verify the knob points to OFF correctly and engages each setting

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

The Oven Rack is an OEM part for LG ranges. This part provides a stable surface for placing cookware during baking, roasting, and broiling.

Causes of a bad oven rack can include exposure to high temperatures over time, which can weaken the metal, or accidental damage that causes bending or warping.  

Symptoms of a bad oven rack include:

• Warping or bending of the rack
• Difficulty sliding the rack in and out of the oven
• The rack not sitting level within the oven

This OEM LG part is also compatible with some Kenmore models.

This switch assembly is the door lock mechanism for select front-load washers. It detects when the door is closed and locks it during operation, allowing the washer to start and run safely without interruptions.

• Monitors door position and signals the control; failure can prevent the cycle from starting or trigger door/lock errors
• Engages the latch to secure the door during wash and spin; a bad lock may stop the cycle mid-wash
• Coordinates door unlock at cycle end; faults can delay or prevent unlocking
• Intermittent operation may cause sporadic starts or pauses

• Disconnect power and turn off water supply before servicing
• Access the lock behind the front panel at the door opening; remove the door boot clamp to reach the mounting screws
• Move wire connectors to the new assembly one at a time to maintain placement
• Reassemble and verify proper locking and unlocking before running a full cycle

The Surface burner grate is an OEM component specifically designed for LG cooktops and ranges. This burner grate sits atop the surface burner to support cookware during use. 

Causes of a bad surface burner grate can include warping, cracks, or breaks from prolonged high-heat exposure. Surface levels may become uneven due to impact or normal wear over time.

Symptoms of a bad surface burner grate include:

• Cookware that is unstable or wobbles during use
• Food or liquid spills into the burner below 
• Difficulty cleaning built up residues from an uneven surface
• Visible damage or cracks in burner grate material

This OEM LG part is also compatible with select Sears/Kenmore ranges and cooktops. 

The Nozzle is an OEM part for LG ranges. It is a small component located inside the burner box that emits gas to create flame. During operation, the nozzle precisely meters fuel flow to each burner to achieve balanced and consistent heating. 

Symptoms of a faulty nozzle include: 

• Burners that light unevenly or emit an irregular flame pattern
• Inability to adjust burner flames or in some cases, lack of ignition
• Possible safety hazard from gas emissions not mixing or igniting properly

Causes can stem from mineral buildup clogging the narrow opening over time. Damage, such as nicks or corrosion, may also disrupt critical gas flow.

This OEM LG part is also compatible with some Kenmore ranges featuring LG gas cooktop systems. Replacing a worn nozzle restores optimal and safe burner performance.

The Nozzle is an OEM part for LG gas ranges. It is a critical component that functions to release gas fuel from the supply line in a regulated and controlled manner to achieve the desired burner flame. The Nozzle has precision-engineered orifices and materials resistant to corrosion to provide reliable and safe operation over extended use.

Symptoms of a bad nozzle include:

• Burner flames that appear uneven, yellow, or unstable 
• Inability to achieve or maintain desired flame height
• Unpleasant gas smells were detected around the range
• Potential safety hazards if damage severely restricts or leaks fuel

Replacing a faulty nozzle restores the exact fuel-air mixture for clean controlled cooking. This affordable OEM LG part ensures optimal and safe burner performance customers expect from their gas range.

This OEM LG part is also compatible with ranges from Crosley, Jenn-Air, and select Kenmore gas models.

This nozzle is the burner orifice that meters gas flow to a single burner, helping your range or cooktop produce a correct, stable flame for consistent heating and cooking performance.

• Controls gas flow to its designated burner for proper flame size and shape
• A clogged, worn, or incorrect nozzle can cause weak or oversized flames, yellow tipping, uneven heating, or noisy flames
• Commonly replaced during LP/Natural gas conversions; each burner requires the exact nozzle specified by the service manual
• Useful to check if burner cleaning doesn't restore normal flame behavior

• Disconnect electrical power and shut off the gas supply before servicing
• Match the nozzle to the exact burner position and gas type; verify markings against the original
• Access under the burner/cooktop; use the correct wrench size and avoid overtightening
• After installation, leak-test all fittings with a soap solution and confirm proper flame characteristics per the manual

This gas valve assembly controls gas flow to the appliance's burner, restoring reliable ignition and heating when the original valve fails. It replaces a faulty or leaking valve to help the unit heat safely and consistently. What it does:

• Regulates and routes gas to the burner based on the appliance's control signals
• Prevents gas flow when the appliance is off or during safety shutoff conditions
• Commonly used to address symptoms like no heat, weak heating, or a persistent gas smell when confirmed at the valve
• Works as the appliance's primary gas control component in the fuel delivery system

• One gas valve assembly

• Turn off gas supply and disconnect power before servicing; verify both are isolated
• Inspect all gas fittings and use an approved leak detection method after installation
• Do not modify the part; use proper tools and follow manufacturer service instructions

This gas valve assembly controls the flow of natural or LP gas to the oven/range burner, restoring safe ignition and burner operation. Replace a faulty valve to help resolve burners or oven not lighting or heating inconsistently. What it does:

• Regulates gas flow to the oven/burner burners so they ignite and maintain a steady flame
• Works with the oven/range ignition system and safety controls to open and close gas supply
• Commonly replaced when burners fail to light, flame is weak or intermittent, or oven won't heat
• Designed as a direct replacement assembly for the original valve configuration

• One gas valve assembly as shown

• Shut off both gas supply and electrical power before beginning any service
• After installation, check all fittings for leaks with a gas leak detector or soapy water and test operation
• Do not alter the valve or regulator; follow appliance manufacturer instructions

This gas valve assembly controls the flow of natural gas to the oven/range burners so the appliance can heat correctly. Replaces a failed valve to restore regulated gas delivery and safe ignition control. What it does:

• Regulates gas flow to the oven/range burner(s) during ignition and operation
• Works with the igniter and safety sensors to allow reliable burner lighting
• Common symptom: oven or burner fails to heat or maintain temperature
• Common symptom: appliance won't ignite or cycles without producing heat

• Turn off gas supply and disconnect power before starting any service
• Inspect and replace any worn gaskets or seals; check fittings for proper torque
• After installation, test for proper operation and check all connections for leaks with a soap solution or approved leak detector

This gas valve assembly controls gas flow to the oven and burners so the range heats properly and maintains safe operation. Replace a failed valve to restore ignition and regulated gas delivery. What it does:

• Regulates gas flow to the oven/burner when the appliance calls for heat
• Enables proper ignition and sustained burner/oven flame
• Common symptom: oven or burners won't heat or light even when controls are set
• Can cause clicking or continuous ignition attempts when valve sticks or fails

• Turn off gas supply and unplug the appliance before starting repairs
• Check all fittings for leaks after installation using a soap solution or approved leak detector
• Do not force connections; replace any damaged seals or tubing to ensure safe operation

This gas valve assembly controls and delivers gas to the burner when the appliance calls for heat. Replacing a failing valve restores reliable ignition, steady flame, and consistent heating performance while maintaining proper safety shutoff when not heating.

• Regulates gas flow to the burner(s) under the appliance's control and safety circuits
• Provides positive gas shutoff when no heat is requested
• Helps resolve no heat/flame, igniter glows or sparks but no ignition, burner lights then goes out, or intermittent heating
• Before replacement, also inspect the igniter, flame sensor, wiring, and regulator settings

• Disconnect electrical power and turn off the gas supply before servicing
• Note connection orientation; transfer any required fittings or brackets from the original valve
• Use an approved gas-rated thread sealant where applicable and leak-test all joints with a soap solution after installation
• Verify proper ignition and stable flame per the product's service or test procedure

This water inlet valve controls water flow into the appliance, allowing proper filling for dispensing, ice making, or cycles that require water. Replaces a failed valve to restore normal water delivery. What it does:

• Opens and closes to allow water into the appliance when a cycle or dispenser calls for it
• Stops water flow when not energized to prevent leaks or overfilling
• Commonly linked to symptoms like no water dispensed, ice maker not filling, or appliance not filling during cycles
• Works as the appliance's fluid control point in the water supply path

• One water inlet valve assembly

• Disconnect power and shut off the water supply before beginning any repair
• Typical installation requires removing access panels and disconnecting inlet hoses and electrical connectors
• Inspect and replace any worn inlet hoses or seals to ensure a reliable seal

The Gas Valve is an OEM part for LG gas ranges. This valve controls the flow of gas to the range's surface burners.

Causes of a bad gas valve include wear and tear over extended use, mineral buildup or mechanical failure restricting gas flow, or damage to electronic sensors and controls.

Symptoms of a bad gas valve are:

• Inability to ignite or light burners
• Unstable burner flame levels
• Gas leaks around connections or seams
• Burners that cannot be turned off securely

This OEM LG part is also compatible with some Kenmore models.

Restore reliable flame performance with this replacement burner. It mixes and distributes gas to produce the cooking flame on your appliance, helping it light consistently and deliver even, controllable heat during everyday use. What it does:

• Directs gas through burner ports to form a controlled cooking flame
• Replaces burners that are cracked, warped, corroded, or clogged
• Can help resolve weak/uneven or yellow flames and delayed ignition
• Restores stable simmer and more even heat distribution

• Includes 1 burner

• Disconnect power and shut off the gas supply; allow the appliance to cool completely
• Access the burner per your model's procedure; remove any grates/caps and retaining hardware if applicable
• Position the new burner over the orifice and igniter; ensure it sits flat and properly aligned
• Reassemble and restore gas/power; test for proper ignition and flame pattern

This Main PCB Assembly is the primary control board that manages a range/oven's functions and user interface, restoring proper control and communication between components when the original board fails. What it does:

• Regulates oven/range functions and timing signals for heating elements and switches
• Powers and communicates with the display, touchpad/buttons, and status indicators
• Helps coordinate safety interlocks and sensor inputs for normal operation
• Commonly replaced for symptoms like unresponsive controls, no display, or intermittent operation

• Disconnect all power at the breaker before accessing the appliance.
• Handle the board carefully to avoid static damage—use ESD precautions where possible.
• Verify power and wiring connections are correct; replace with the exact OEM board only.

This burner is the cooktop surface flame assembly that produces heat for cooking. It replaces a damaged or worn surface burner to restore proper flame and even heating on the cooktop. What it does

• Provides the primary flame source for a gas cooktop burner
• Restores consistent flame distribution when the original burner is warped, cracked, or clogged
• Can resolve symptoms such as weak or uneven flame, burner that won't sustain a flame, or visible damage to the burner head
• Works with the igniter/safety valve assembly to light and maintain the burner

• One surface burner

• Turn off gas supply and power to the appliance before servicing
• Use basic hand tools; handle the burner carefully to avoid bending or damaging the ports
• Clean burner ports of debris before installation to ensure proper flame pattern

The Burner Cap is an OEM part for LG ranges. It covers the burner assembly on the cooktop and directs flame for efficient cooking. Burner caps allow heat to be spread evenly across pans while containing dangerous flames and sparks.

Causes of a bad burner cap generally include cracks, warping, or damage from high heat over time. Accidental mishandling or impact can also weaken burner caps.

Symptoms of a bad burner cap include:

• Inefficient or uneven heating of cookware
• Visible flames escaping outside the burner area
• Cracks or holes in the burner cap surface
• Looseness, wobbling, or inability to properly secure the cap

This OEM LG part is also compatible with some Kenmore models.

This cable assembly is the wire harness that carries power and control signals between appliance components, helping restore electrical connections and reliable operation. What it does:

• Routes power and signal connections between control boards, motors, sensors, and other modules
• Restores interrupted electrical paths that can cause intermittent operation or component failure
• Helps resolve symptoms such as component non-response, error codes tied to connectivity, or loss of certain functions
• Maintains proper connector alignment and secure contacts when installed correctly

• Disconnect power to the appliance before starting any repair
• Handle connectors carefully; match connector shapes and orientation before seating
• Route the harness away from sharp edges, moving parts, and heat sources to prevent damage

This replacement pipe/tubing routes fluids inside the appliance, restoring proper channeling of water or condensate to prevent leaks and ensure normal operation. Use when the original tubing is cracked, clogged, or damaged. What it does:

• Provides a sealed pathway for water or condensate to move between components
• Prevents leaks by replacing cracked or brittle tubing
• Restores proper flow when original pipe is clogged, kinked, or collapsed
• Helps eliminate odors or water pooling caused by damaged tubing

• One replacement pipe/tubing as shown

• Turn off power and water supply to the appliance before beginning service
• Inspect connection ends and replace any damaged clamps or fittings
• Use appropriate tools and avoid over-tightening clamps to prevent pinching the pipe

This is a replacement pipe used in the appliance's water/ice system to route water between components and maintain proper water flow. Replacing a damaged pipe restores reliable water delivery and helps prevent leaks. What it does:

• Carries water between the inlet, dispenser, and/or ice maker components
• Stops or reduces leaks when a cracked or corroded pipe is replaced
• Helps restore normal water flow if an internal blockage or break caused reduced dispensing
• Maintains proper routing to prevent kinks or stress on fittings

• Turn off the appliance power and shut off the household water supply before starting.
• Remove only the damaged pipe and install the matching replacement; use the same routing and fittings.
• Tighten fittings to manufacturer torque guidance and check all connections for leaks after restoring water.

This small, board-mounted tactile push-button switch is used on the control panel. It registers a momentary press so the control board can accept your selection. Replacing a worn switch restores reliable button response and consistent operation.

• Mounts to the user interface board and provides momentary contact when a button is pressed
• Sends a low-voltage signal to the control, enabling cycle or option selection
• Typical failure symptoms: unresponsive or intermittent buttons, needing extra force to register, stuck/always-on input, or unintended beeps/changes
• Helps restore consistent user-interface input when an individual button switch has failed

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Access the control panel to reach the user interface board
• This is a board-level repair; note switch orientation. Replacement may require desoldering/soldering per OEM procedure
• Use ESD precautions and avoid overheating PCB pads; test button function before reassembly

This genuine replacement power cord assembly restores electrical power to the appliance by replacing a damaged or worn main power cable. It provides a direct, factory-fit connection for safe, reliable operation. What it does

• Delivers mains power from the wall outlet to the appliance's internal wiring and control systems.
• Replaces frayed, cut, melted or otherwise damaged cords that can cause loss of power or intermittent operation.
• Helps eliminate burning smells, visible damage, or exposed wires that indicate a compromised power connection.
• Restores a secure plug and strain-relief connection to reduce stress on terminal connections.

• One power cord assembly.

• Always disconnect power at the breaker or unplug the appliance before starting any work.
• Verify correct cord routing and secure the strain relief/retainer to prevent pinching or chafing.
• Tighten terminal screws to the manufacturer's specification and ensure proper grounding.

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Motor, AC Fan is an OEM part for LG ovens. This fan motor is responsible for circulating air within the oven cavity, ensuring even heat distribution for consistent cooking and baking results. It helps maintain the oven’s temperature by moving hot air around, which is especially important for convection ovens.

Over time, the fan motor can wear out or become faulty due to continuous use, exposure to high temperatures, or electrical issues. When the fan motor fails, it can lead to uneven cooking and potential overheating of the oven.

Symptoms of a bad oven motor, AC fan include:

• Uneven cooking or baking results
• Unusual noises coming from the oven during operation
• The oven taking longer to preheat
• The fan not spinning or running intermittently
• Error codes related to fan or airflow issues

This OEM LG part is also compatible with Sears/Kenmore models.

A replacement motor bracket that secures the motor to the appliance chassis for stable operation and reduced vibration. Restores proper motor alignment to help maintain smooth, quieter cycles and protect drivetrain components. What it does:

• Holds the motor firmly in place to prevent movement during operation
• Maintains correct motor-to-transmission/gear alignment for reliable power transfer
• Reduces vibration and rattling that can occur when mounts fail
• Helps prevent premature wear of motor and connected components
• Addresses symptoms such as excessive noise, shaking, or motor misalignment

• Disconnect power to the appliance before servicing; follow lockout/tagout best practices
• Turn off water supply and relieve any residual pressure for washer models before disassembly
• Basic mechanical skills and common hand tools required; bracket removal may require loosening motor fasteners and supports
• Reuse OEM fasteners if undamaged and torque to manufacturer specs; inspect surrounding mounts and hardware for wear

This replacement ring secures or positions a nearby appliance component to restore proper alignment and stable operation. It's a small but important part that helps reduce excess movement and related wear. What it does:

• Holds or locates a mating component to prevent unwanted movement or misalignment
• Helps reduce vibration and knocking noises caused by loose parts
• Restores correct spacing that maintains smooth mechanical operation
• Can prevent accelerated wear on adjacent parts when functioning properly

• Disconnect power (and water supply if applicable) before beginning any repair
• Access location may require removing panels or trim; keep fasteners organized
• Inspect surrounding parts for wear or damage and replace if needed

The Convection Fan Blade is an OEM replacement part for LG ovens. It works by circulating hot air throughout the oven, reducing cold spots and promoting consistent temperatures.

Causes of a malfunctioning Convection Fan Blade can be wear and tear from regular use, the accumulation of debris hindering the blade’s rotation, or mechanical issues impacting the fan motor or blade alignment.

Symptoms of a bad Convection Fan Blade include:

• Uneven cooking or baking, leading to partially cooked food
• Noises emanating from the oven during operation, indicating possible damage or obstruction
• The fan not rotating or moving irregularly, signaling mechanical issues

This OEM LG part is also compatible with Sears/Kenmore oven models.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

This insulator is the mica sheet that covers the microwave's waveguide opening. It shields the cavity from food splatter and moisture while allowing microwave energy to pass, helping prevent arcing and protecting internal components.

• Covers the waveguide port to keep grease and debris out
• Helps prevent sparking/arcing inside the cavity
• Restores safe, even microwave operation when the original is burned or stained
• Typical symptoms: visible burn marks or charring on the cover, arcing/sparking during use, unusual noises

• Unplug the appliance before service; high-voltage components can retain charge
• Remove the old cover by releasing mounting screw or tabs; clean residue from the area
• Do not bend or crack the new mica; install with the same orientation
• If trimming is required per service literature, follow the outline of the original cover only

This insulator is a small mounting and thermal-isolation part that cushions and separates internal components to help prevent heat transfer and unintended contact. It supports reliable appliance operation by protecting nearby parts from heat and vibration. What it does:

• Provides physical spacing to prevent electrical contact between adjacent components
• Reduces heat transfer to temperature-sensitive parts
• Cushions components to reduce vibration noise and wear
• Helps maintain proper alignment of mounted parts

• Disconnect power before accessing internal components to avoid shock
• Replace only with the same style and position to maintain proper spacing and thermal protection
• Inspect the surrounding area for heat or abrasion damage and replace any compromised parts

This bracket secures the turntable motor to the microwave oven cavity base, keeping the motor properly aligned so the glass tray can rotate smoothly for even heating.

• Supports and positions the turntable motor beneath the oven floor
• Helps resolve issues like a non-turning glass tray or jerky rotation
• May correct intermittent grinding or scraping noises from the tray area

• Unplug microwave before servicing; high-voltage components can retain a charge
• Remove the unit from its install location if required for bottom access
• Access turntable motor from the underside; support the cavity to prevent damage
• Reuse existing screws and motor unless otherwise specified

This incandescent oven lamp provides interior illumination so you can safely check food without opening the door. Direct replacement for a burned or dim oven/range light to restore cooking visibility. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores clear visibility of the oven cavity for monitoring cooking progress
• Helps avoid opening the oven door unnecessarily, preserving oven temperature
• Fits the original lamp socket and installs in the oven light housing

• Disconnect power to the appliance before replacing the lamp to prevent electric shock
• Allow the oven and old bulb to cool completely before handling
• Use a cloth or gloves when installing the new lamp to avoid transferring oils from skin

A full-perimeter refrigerator door gasket that restores an airtight seal to help maintain proper cooling and reduce energy loss. Designed to replace a worn, cracked or torn door seal for reliable temperature control. What it does

• Seals the door to keep cold air in and warm air out, helping the appliance maintain set temperatures
• Common symptom: visible gaps, cracks, or tears in the gasket allowing cold air to escape
• Common symptom: excessive frost or condensation inside the compartment near the door
• Common symptom: refrigerator runs more often or works harder to maintain temperature
• Helps prevent food spoilage caused by inconsistent cooling when the original gasket fails

• One full-perimeter refrigerator door gasket

• High-level task: remove the old gasket and press the new gasket into the channel or attach per the manufacturer's method
• Gasket may require slight warming or alignment to seat evenly; follow OEM instructions for final fit
• Inspect mounting channel and clean surface before installation to ensure a proper seal
• Safety first: unplug the appliance before working on the door and take care not to damage trim or wiring

This nozzle directs and controls water flow within the appliance to ensure proper cleaning performance. Replacing a worn or damaged nozzle helps restore consistent spray and overall wash results.

• Directs water to targeted areas for effective washing
• Can help reduce unusual spray patterns or noisy water flow
• Restores intended wash coverage when the original nozzle is cracked or clogged

• Disconnect power and water before servicing
• Note the nozzle's orientation and connection points during removal
• Inspect seals and mating surfaces for debris or damage before reassembly
• Test for leaks and proper spray after installation

This burner assembly replaces a damaged or worn surface burner so the cooktop heats reliably and flames are properly directed for cooking. Fits into the range's burner well and connects to the cooktop gas/ignition system. What it does:

• Provides the burner head and mounting needed to produce and shape the cooking flame
• Restores consistent ignition and even heating when the original burner is cracked, warped, or missing
• Stops erratic flame behavior caused by damaged or misaligned burner components
• Works with the appliance's existing valve and igniter to allow normal cooktop operation

• One complete burner assembly

• Turn off gas supply and disconnect power before attempting service
• Handle parts carefully to avoid damaging the burner surface and sealing surfaces
• Inspect nearby seals, gaskets and the igniter for damage; replace as needed

This governor assembly is the mechanical control that stabilizes and regulates motion within the appliance's drive mechanism. Replacing a worn governor restores smooth, consistent operation and helps prevent erratic movement that can strain connected components. What it does:

• Regulates and limits the speed/rotation of the linked drive for stable, predictable movement
• Helps synchronize gears or shafts so the mechanism operates smoothly
• Common symptoms: intermittent or no movement, jerky/erratic motion, clicking or grinding noises
• Visible wear, cracks, or a loose/broken hub on the original governor

• 1 governor assembly

• Disconnect power before servicing; allow moving parts to come to a complete stop
• Note the original orientation; take photos to aid reassembly
• Transfer any reusable brackets, clips, or spacers from the original if required
• After installation, rotate the mechanism by hand to verify free movement before restoring power

This replacement water inlet valve controls water flow to the dispenser and ice maker, restoring reliable water delivery and helping stop leaks or no-water symptoms. Designed to match the OEM function and fit. What it does:

• Opens and closes water flow to the dispenser and ice maker when signaled by the appliance
• Restores water delivery when a failed valve causes little or no water flow
• Stops unwanted water flow or leaking when the valve no longer seals
• Works with the appliance's fill and dispenser circuitry to meter water

• Disconnect power and shut off the home water supply before starting
• Replace only with the correct valve for this part number;
• Use basic hand tools; avoid overtightening fittings to prevent leaks
• After installation, restore power and water, then run the dispenser/ice maker and check all connections for leaks

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This genuine accessory assembly replaces a worn or damaged mounting or trim assembly to restore proper fit and secure accessory components on the appliance. Use it when factory-mounted accessories are loose, misaligned, or missing fasteners. What it does:

• Secures accessory components and restores proper alignment
• Reduces rattling or movement caused by a loose accessory
• Helps maintain proper fit between the accessory and appliance housing
• Supports normal operation by keeping accessory parts in place

• Disconnect power and water before starting any repair
• Use basic hand tools and keep fasteners organized during removal/installation
• Follow OEM instructions for proper placement and torque
• Handle plastic trim and clips carefully to avoid cracking during installation