Parts for Lg LPXS30866D/00: Other Parts

Removes contaminants for clean, fresh-tasting water and ice. Replace every 6 months or 200 gallons to maintain water quality. Verify fit with your model.

Water pooling under your refrigerator? A damaged drain tube assembly causes leaks and water buildup. This direct-fit part restores proper drainage.

Fix water pooling or leaking inside your refrigerator by replacing a cracked or clogged drain tube assembly. Channels defrost water to the drain pan.

Keeps refrigerator air fresh by filtering odors and contaminants. Replace every 6 months or when indicator alerts. Confirm fit with your model number.

Molded exterior panel that shields internal components. Replace when cracked or missing to restore proper fit and protection. Verify fit with your model.

Center plate assembly for bottom-mount refrigerators. Replaces cracked, broken, or missing center plates. Installs in the interior compartment.

Replace your broken or cracked refrigerator vegetable crisper drawer assembly. This clear plastic bin installs in the lower fresh food section.

Fix a refrigerator not cooling properly or running too warm with this temperature sensor. Monitors internal temps to maintain proper cooling.

Fix refrigerator door misalignment or poor sealing with this door alignment magnet. Restores magnetic retention to keep panels and components secure.

Seals your refrigerator door to maintain proper temperature and prevent air leaks. Replace if torn, cracked, or not sealing properly. Confirm fit with your model.

Seals your refrigerator door to maintain proper temperature and prevent air leaks. Replace if torn, cracked, or not sealing properly. Confirm fit with your model.

Door foam assembly for your refrigerator. Installs inside the door panel to provide insulation. Replace if foam is cracked, compressed, or missing.

Seals the refrigerator door to keep cold air in and warm air out. Replace if worn, torn, or moldy to restore proper temperatures and efficiency.

Replaces worn door gasket to restore airtight seal, prevent warm air leaks, reduce frost and condensation. Check your model number for proper fit.

Replacement door stopper for bottom-mount refrigerators. Prevents door from swinging too far and damaging hinges. Replace if cracked, broken, or missing.

This rubber door stopper cushions and limits appliance door movement to prevent hard closing, reduce noise, and protect the cabinet and door edge from damage. Designed as a direct-fit replacement for the original factory bumper. What it does:

• Absorbs impact when the door closes to reduce slamming and rattling
• Keeps the door aligned and prevents metal-on-metal contact or chipping
• Helps maintain door seal integrity by stabilizing closing position
• Commonly replaced when worn, torn, or missing and causing noise or misalignment

• One rubber door stopper

• Basic push-fit replacement—remove the old bumper and press the new stopper into the mounting hole
• Inspect the mounting boss for damage; replace the housing if the mounting area is broken
• Disconnect power or ensure appliance is off and stable before working on doors for safety
• No special tools typically required; use a flat tool for leverage if the old bumper is stuck

Cushions and limits refrigerator door movement to prevent slamming. Replace this stopper if cracked, worn, or missing to protect cabinet and hinges.

Upper door hinge assembly for refrigerators. Mounts at the top of the door to support and align proper opening and closing. Replace if cracked or worn.

Replaces worn, cracked, or non-responsive control panel buttons on your refrigerator. Restores tactile feedback and proper panel appearance.

Replacement door basket assembly for refrigerator doors. Restores storage for bottles, jars, and condiments. Replaces cracked, broken, or missing bins.

Roller component for the ice dispenser door handle on bottom-mount refrigerators. Replaces broken, worn, or missing rollers. Ensures smooth handle operation.

Replacement door stopper for refrigerators. Cushions door closure to prevent slamming and reduce noise. Install if your original is cracked, broken, or missing.

Hinge-mounted stopper that controls your refrigerator door's opening angle. Replace if cracked, broken, or missing to restore smooth movement.

Spanner wrench tool for adjusting refrigerator door hinges. Enables precise up-and-down door alignment in tight spaces. Replace if lost or damaged.

Microwave door won't latch or release properly? This lever holder bracket secures the door lever assembly to restore smooth door operation. Easy DIY fix.

Replace your refrigerator's display cover assembly if the plastic lens is cracked, scratched, or missing. Protects the control panel electronics.

Drain tray that collects defrost water beneath your refrigerator. Replace if cracked, broken, or missing to prevent water leakage onto your floor.

Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.

Refrigerator not cooling properly? This condenser coil assembly releases heat to keep your fridge cold. Professional installation recommended for evacuation.

Not cooling properly? This refrigerator evaporator assembly removes heat from the interior. Moderate difficulty repair requiring refrigerant knowledge.

Fix refrigerator not cooling or freezing issues with this evaporator coil assembly. Intermediate repair requiring defrost system knowledge. Restores proper cooling.

Compressor running hot or error code 22? This thermistor assembly monitors compressor temperature to prevent overheating. 10-minute DIY repair.

Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.

Fix erratic temperature readings or sensor errors with this PTC sensor cover. Shields the sensor from debris and damage. Simple 5-minute snap-on repair.

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

Water pooling inside your refrigerator? This drip tray collects condensate and defrost water to prevent leaks. Direct-fit replacement part.

Fixes uneven cooling and scraping noises by directing airflow from the fan. This guide restores proper air circulation throughout your refrigerator.

Fix a refrigerator not cooling properly with this compressor sealing pipe. Essential sealed system component for restoring proper refrigeration.

Replaces broken or missing refrigerator door stop. Limits door travel to prevent over-extension and maintain proper alignment and smooth operation.

Rattling or loose parts in your refrigerator? This retaining pin secures moving components and keeps them aligned for smooth, quiet operation.

Support roller that mounts to the refrigerator base, allowing the unit to roll for cleaning or service. Replace if worn, broken, or causing uneven positioning.

Fix refrigerator not cooling properly or running constantly with a new drier assembly. Removes moisture from refrigerant. Requires EPA-certified technician.

Secure loose internal components with this refrigerator mounting clip. Replace if parts shift or become misaligned. Verify fit with your model number.

Fix a refrigerator that won't cool, has temperature issues, or shows error codes with this electronic control board. Moderate DIY repair in 1-2 hours.

Fix a refrigerator that won't turn off the light or runs constantly with this door switch magnet. Works with reed switches. Simple DIY replacement.

Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.

Fix refrigerator cooling issues or unusual noises with this DC motor assembly. Common repair for failed evaporator fan motors in bottom-mount models.

Fix refrigerator cooling issues or unusual noises with this DC motor assembly. Common repair for failed evaporator fan motors in bottom-mount models.

Plastic cover that protects the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor component.

Protects your refrigerator's light bulb from moisture and damage. Replace if cracked, discolored, or broken to maintain proper lighting and safety.

Fix a refrigerator that won't cool properly or makes unusual noises. This drive motor restores proper operation for consistent temperature control.

If your refrigerator won't power on or has a damaged cord, this power cord assembly restores safe electrical connection. Direct-fit replacement.

Fix a refrigerator that won't turn off the light or runs constantly with this door switch magnet. Works with reed switches. Simple DIY replacement.

Supports and stabilizes your refrigerator door for proper alignment. Replace if bracket is cracked, broken, or causing door misalignment issues.

LED light assembly for bottom-mount refrigerators. Installs inside compartment to illuminate interior. Replace when cracked, dim, or not illuminating.

LED light assembly that mounts in the freezer compartment to illuminate the bottom drawer. Replace if the light housing is cracked, broken, or missing.

Replaces worn LED backlight strip in your refrigerator display. Restores screen brightness and clarity when images appear dim or uneven. Verify fit with your model number before ordering.

Fix a refrigerator that won't cool, has no power, or shows error codes with this main power control board assembly. Moderate difficulty repair in 1-2 hours.

Fixes refrigerator not cooling, display not working, or erratic temperature control. This power control board restores electronic functions and power distribution.

If your refrigerator display is dead, shows error codes, or behaves unpredictably, this sub PCB assembly processes inputs and controls specific functions.

Fix temperature inconsistencies or error codes with this refrigerator sensor cover. Protects temperature sensors for accurate cooling. Simple 10-minute fix.

Ice maker not making ice or constantly leaking? This ice maker assembly kit restores ice production. DIY-friendly installation takes under an hour.

Secures components in your refrigerator assembly, reducing vibration and keeping parts properly seated. Replace when damaged or missing to restore snug fit. Verify model compatibility before ordering.

Ice won't dispense but ice maker works? The auger motor drives ice from the bin to the chute. Moderately easy repair with our video guide and DIY tips.

Structural bracket that secures internal components in your refrigerator. Replace if cracked, broken, or worn to restore proper alignment and stability.

Fix inaccurate temperature readings or sensor errors with this refrigerator sensor control board. Restores proper sensor communication and feedback.

Ice bin cracked, warped, or causing weak dispensing and jams? This ice bucket assembly stores and delivers ice to your dispenser. Easy DIY repair.

Ice maker icing over or not producing ice? This motor drives the auger and crusher mechanism. Direct-fit replacement restores ice production.

Connects water tubing inside your refrigerator to supply the ice maker and water dispenser. Replace if cracked, leaking, or unable to hold tubing securely.

Water supply line connects reservoir to dispenser and ice maker. Replace if cracked, leaking, or damaged at connection points. Installs inside refrigerator.

Fix inconsistent heating or burner ignition issues with this gas valve assembly. Controls gas flow to the burner system for reliable flame control.

Fix bad-tasting water or slow ice production with this refrigerator water filter assembly. Restores proper water flow to dispenser and ice maker.

No water or ice? Leaking water valve? This inlet valve controls flow to your ice maker and dispenser. Common DIY fix with video guide included.

Plastic trim cap that snaps over exposed fasteners and mounting posts on your refrigerator. Replace if cracked, broken, missing, or discolored.

Fix water leaks around your filter with this refrigerator water filter head assembly. Secures filter cartridge and routes water to dispenser and ice maker.

Removes contaminants for clean, fresh-tasting water and ice. Replace every 6 months or 200 gallons to maintain water quality. Verify fit with your model.

Secures and supports refrigerator door pivot for proper alignment and smooth operation. Replace when door sags, seals poorly, or binds. Confirm fit with model.

Replacement door hinge assembly for your refrigerator. Installs on the cabinet to support the door. Replace if cracked, bent, or worn for proper alignment.

Molded door shelf cover for the home bar compartment. Replaces cracked, broken, or missing covers. Installs on the refrigerator door for a finished look.

Freezer door won't lock or close securely? This lever cover protects the door lock mechanism from wear and impact damage. Easy DIY installation.

Replaces a cracked, broken, or missing ice dispenser door handle on your refrigerator. Installs on the exterior dispenser for easy ice access.

Roller component for the ice dispenser door handle on bottom-mount refrigerators. Replaces broken, worn, or missing rollers. Ensures smooth handle operation.

Seals the ice bank door to prevent warm air from melting ice and causing clumping. Replace if ice melts, refreezes into clumps, or frost forms around the bin.