Parts for Lg LSE4613BD/00: Other Parts

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

This flat hardware washer helps secure bolts and fasteners in the washer assembly to keep panels and components seated and stable. Simple replacement can restore proper clamping and reduce movement around joints. What it does:

• Provides a smooth bearing surface under nuts or bolt heads to distribute load
• Prevents fasteners from loosening due to vibration or movement
• Helps maintain proper alignment of panels and small components
• Worn, corroded, or missing washers can cause loose panels, increased noise, or premature fastener wear

• Replace with the same type and size washer removed from the appliance
• Use basic hand tools; support the assembly to avoid stress on other components
• If corrosion or thread damage is present, replace the bolt/nut as well
• Disconnect power and follow manufacturer safety guidance before servicing

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This customized screw secures appliance components where a standard fastener won't fit, helping keep panels, brackets and small assemblies stable. It's a direct-fit replacement when the original specialized screw is missing or damaged. What it does:

• Fastens and holds appliance panels, brackets or small parts in place
• Prevents rattling, loose trim or misaligned components caused by a missing or stripped screw
• Matches the OEM fit and thread pattern for proper engagement and alignment
• Used in locations that require a non-standard or customized fastener

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can strip threads or crack parts
• Keep removed hardware organized so you can reinstall in the original location

This hardware washer helps distribute fastener load and maintain proper spacing in your LG appliance. Replacing a missing or worn washer restores secure mounting and alignment, reducing vibration and rattling from loose assemblies.

• Distributes the load of a screw or bolt and protects mating surfaces to maintain alignment
• Helps keep components secure and at the correct spacing
• A damaged or missing washer can lead to loosening, vibration, or rattling during operation
• Ensures correct hardware stack-up during reassembly after service

• Disconnect power and shut off water or gas before servicing
• Note the order and orientation of any washers/spacers; take a reference photo
• Use the correct driver or wrench and tighten snugly—do not overtighten
• Replace companion hardware if corroded, stripped, or damaged

The Common Nut is an OEM part for LG ranges. It secures the fan blade to the motor shaft. This nut maintains the fan's stability and preventing it from becoming dislodged during use.

Causes of a bad common nut can include loosening over time due to vibration, improper installation, or damage from impact or mishandling.

Symptoms of a bad common nut include:

• Excessive noise or vibration from the fan assembly
• The fan blade becoming loose or detached, causing poor air circulation
• Potential risk of the fan blade becoming a projectile if completely detached

This OEM LG part is also compatible with some Kenmore models.a

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This knob assembly replaces a worn or broken control knob to restore reliable selection of cycles and settings on the appliance console. It provides the tactile grip and indexed stop needed for accurate control. What it does:

• Replaces a cracked, stripped, loose, or missing control knob to regain smooth turning and positive engagement
• Ensures pointer aligns with console markings so selected settings register correctly
• Stops slipping on the control shaft that causes settings to change unintentionally
• Restores user control for selecting cycles, temperatures, or timer positions

• Disconnect power (and gas if applicable) before any service
• Remove the old knob by pulling straight off the shaft; some consoles may require removing a trim or panel first
• Align the replacement knob to the splines and push fully onto the shaft until it seats

The PCB Assembly, Sidekey is an OEM replacement part for LG  ranges. This printed circuit board assembly is responsible for controlling the functions of the control panel on the side of the range. It communicates with all electronic components to operate the cooktop burners, oven lights and fans, and programming features.   

Causes of a bad PCB assembly can include corrosion of printed circuits over time due to heat exposure, moisture damage, or component failure.

Symptoms of a bad PCB assembly include: 

• Cooktop burners not working properly or unresponsive to control panel commands
• Inability to turn on oven lights or fans
• Programming features like timers or temperatures not functioning correctly
• Blank or unresponsive control panel displays

This OEM LG part is also compatible with Sears/Kenmore ranges. Replace yours today with this genuine electronic control board and upgrade the functionality of your electric range oven.

This PCB assembly is the appliance's main control board that manages cycle commands, sensor signals and user inputs to keep the appliance operating correctly. Replacing a faulty board restores control and communication functions. What it does:

• Receives inputs from the control panel and sends commands to motors, valves and heaters
• Monitors sensor signals and timing functions to coordinate cycles
• Stops operation or causes errors if the board fails or loses power
• Common symptom link: unresponsive controls, error codes, or appliance that won't start

• One PCB assembly (control board)

• Disconnect power before starting and verify power is removed to avoid shock
• Handle the board carefully and avoid touching components or connectors; observe electrostatic discharge (ESD) precautions
• Inspect connectors and wiring for damage and ensure secure connections during reassembly

The Encoder Board is an OEM part for LG ovens. This board is responsible for interpreting the inputs from the control knobs and buttons on the oven's control panel. It sends these signals to the main control board, which then adjusts the oven settings accordingly, such as temperature and cooking mode.

Causes of a bad encoder board can include electrical surges, wear and tear from frequent use, or physical damage to the board's components. A malfunctioning encoder board can disrupt the communication between the user interface and the oven's control system.

Symptoms of a bad encoder board include:

• Unresponsive control knobs or buttons
• Incorrect oven temperature settings
• Oven not starting or turning off unexpectedly
• Error codes displayed on the control panel

This OEM LG part is also compatible with Sears/Kenmore.

This customized screw is the exact fastener specified by the manufacturer to secure components in select LG appliances. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps maintain proper alignment over time.

• Secures panels, brackets, and internal assemblies at original mounting points
• Helps reduce vibration and rattling noises from loose hardware
• Replaces missing, rusted, or stripped screws
• Supports stable operation by keeping parts firmly in place

• Disconnect power; shut off water or gas before service
• Match the screw to the exact location using your model's parts diagram
• Start threads by hand; tighten snugly without overtightening to avoid stripping
• Use the correct driver bit for the head style to prevent damage

This single wiring harness connects appliance components to ensure reliable electrical signals and restores proper circuit continuity. Use it to replace a damaged or worn harness and help remove intermittent power or function failures. What it does:

• Carries electrical signals between controls, motors, and sensors to enable normal operation
• Restores proper connections when original wiring is frayed, burnt, or damaged
• Helps eliminate intermittent faults, loss of power to a component, or erratic operation caused by bad wiring
• Matches original connector types and routing for a direct replacement

• One pre-assembled single wiring harness as pictured

• Disconnect power (unplug or switch off breaker) before starting any repair
• Inspect mating connectors and terminals; replace any corroded or damaged parts

This radiation heater is the element that delivers direct radiant heat for the microwave's grill/browning feature. Replacing a failed heater restores proper grilling performance and helps foods brown and crisp during grill or combination-cook settings. What it does:

• Supplies radiant heat for grill/browning and combo-cook modes
• Typically mounted at the top of the cavity to radiate heat downward
• Common failure symptoms: no heat in grill mode, element does not glow, poor or uneven browning
• Visual clues can include cracks, blistering, or burnt spots on the heater

• 1 radiation heater element

• Disconnect power before servicing; microwaves contain high-voltage components that can retain a charge even when unplugged
• Access may require removing the outer case and interior shroud; beware of sharp metal edges
• Note wire positions before removal; route leads away from hot or moving parts during reassembly
• Verify secure mounts and connections before testing the grill function

The Dual Surface Element is an OEM part for LG ranges. This part is located on the cooktop and provides heat for cooking. It features two heating zones, allowing for versatile cooking options and accommodating different pot and pan sizes.

Causes of a bad dual surface element can include wear and tear over time, damage from heavy cookware, or electrical issues that cause the element to malfunction.

Symptoms of a bad Dual Surface Element include:

• The element not heating up or only heating partially
• Uneven heating or hot spots
• Visible damage or discoloration on the element
• The element cycling on and off irregularly

This OEM LG part is also compatible with some Kenmore models.

This Radiant Surface Element is an OEM replacement part for LG electric ranges and cooktops. It is a high-power coil heating unit located below the cooktop surface that provides efficient, customizable heat for various cooking needs.

Causes of failure can be wear and damage to coiled filaments from prolonged heating cycles, cracking of ceramic insulators, or loose wiring connections suffering arcing or resistance over time.

Symptoms of a faulty element include:

• Slow or inadequate heating of cookware even on high settings
• Temperature fluctuations within the heating zone
• Burning or charring of spills and foods on the element itself
• Tripped circuit breakers obstructing range operation

This replacement is also compatible with some Kenmore models

Replace a failed logic board with this main control board. It manages power distribution and system logic so your appliance starts, runs, and cycles correctly when the original board is damaged or unresponsive.

• Supplies and directs power to key components such as motors, fans, heaters, valves, and lights
• Interprets inputs from sensors and the user interface to coordinate proper operation and cycles
• Helps resolve symptoms like no power, won't start, components not running or cycling, frequent clicking from the control area
• A failed board may show scorch marks, a burning odor, or cause intermittent shutdowns and error codes

• Disconnect electrical power before servicing; shut off water supply if your appliance has one
• Use anti-static precautions; handle the PCB by the edges only
• Photograph/label all wiring; move connectors to the new board one at a time to avoid miswiring
• Ensure the board is secured in its housing/bracket, reinstall covers, restore power, and test

This is a replacement outer door frame that restores the door's structure and appearance and helps maintain a proper seal. It's a direct-fit exterior trim piece designed for compatible LG refrigerator doors. What it does:

• Replaces a cracked, bent or damaged outer door frame to restore door alignment and cosmetic finish
• Supports the door outer panel and provides mounting surfaces for handles and trim
• Helps maintain an even door seal by keeping the door edges square
• Stops drafts and reduces moisture entry at the door perimeter when the seal and frame are intact

• Disconnect power to the appliance before starting any repair
• Remove door shelves, handle and any trim pieces as required to access fasteners
• Handle the frame carefully to avoid scratching the finish; use proper fasteners and follow OEM torque guidance

This handle supporter is the bracket that anchors the door handle to the appliance door, keeping the handle secure and aligned. Replacing a cracked or stripped supporter restores a solid, dependable grip on the door.

• Secures the handle to the door and maintains proper alignment
• Helps fix a loose, wobbly, or detached handle
• Replaces a broken or worn mounting bracket that won't hold screws

• Disconnect power and, if applicable, shut off water before service
• Remove the handle and any trim to access the supporter and mounting screws
• Transfer or replace screws as required; do not overtighten into plastic
• Verify handle alignment and operation before fully reassembling

This parts assembly replaces a damaged or worn assembly to restore proper operation and eliminate loose or broken components. Designed as a direct-fit replacement to return the appliance to normal function quickly. What it does:

• Replaces a damaged internal assembly that can cause intermittent operation or failed cycles
• Stops unusual noises or rattling caused by loose or broken parts
• Restores mechanical alignment and secure mounting where the original assembly is worn
• Helps resolve symptoms like visible damage, loose components, or inconsistent performance

• Disconnect power (and gas/water if applicable) before starting work
• Handle electrical connectors and fragile components carefully to avoid damage

The Oven Selector Knob Supporter is an OEM replacement part for LG ovens. It is a crucial component that provides structural support and ensures proper functioning of the oven selector knob mechanism.

Symptoms of a bad oven selector knob supporter:

• Loose or wobbly oven selector knob
• Difficulty in turning or selecting oven functions
• Knob becoming detached or falling off
• Misalignment or binding of the knob mechanism

Causes of a faulty oven selector knob supporter can include physical damage, wear and tear over time, or manufacturing defects that compromise its structural integrity or alignment.

This OEM LG part is also compatible with Sears/Kenmore ovens.

This single wiring harness connects appliance components to route power and signals reliably, restoring electrical continuity for normal operation. It's a direct-fit replacement when the original harness is damaged or corroded. What it does:

• Carries power and control signals between components so circuits complete and controls respond
• Replaces frayed, burned, or broken wiring that can cause intermittent operation or loss of function
• Helps stop shorts, arcing, or connector-related failures when the original harness is compromised
• Matches OEM connector types and pin arrangements for an accurate replacement

• Disconnect power (unplug appliance or switch off breaker) before beginning any work
• Handle connectors gently; avoid pulling on wires—release locking tabs first
• Route and secure the harness away from hot surfaces and moving parts to prevent wear

This single wiring harness routes electrical power and signals between components to restore proper connections and reliable operation. It replaces a damaged or worn harness to help eliminate intermittent power or control issues. What it does:

• Transfers power and control signals between appliance components to maintain proper function
• Replaces frayed, burnt, or damaged wiring that can cause intermittent operation or component failure
• Helps resolve symptoms like loss of power to a module, erratic behavior, or failure to respond
• Provides a direct plug-and-play connection when matching the correct factory harness

• Disconnect all power (unplug or switch off circuit breaker) before starting any work
• Handle connectors gently and seat firmly until they click into place

This is a single wiring harness that routes power and signals between appliance components to restore reliable electrical connections. It replaces a damaged or worn harness so controls and features can communicate properly. What it does:

• Carries power and control signals between specific components
• Restores interrupted circuits that can cause intermittent operation or component failures
• Helps resolve symptoms like no power to a component, inconsistent function, or error codes tied to open/shorted wiring
• Provides factory-style connectors for a direct fit and reliable connections

• Disconnect power (unplug or turn off breaker) before installing to avoid shock or damage
• Inspect connectors and routing, match connector types and wire colors before connecting
• Avoid pinching or sharply bending wires; secure harness using existing clips or ties

The PCB Supporter is an OEM part for LG ranges and cooktops. It securely mounts and positions the printed circuit board controlling cooking functions.

Causes of a bad PCB Supporter can include cracking or breaking of mounting clips over time due to normal range vibrations and use.  

Symptoms of a bad PCB Supporter include:

• The control board detaching during use
• Intermittent power to heating elements or displays
• Error messages regarding electrical component issues

This OEM LG part is also compatible with some Kenmore models.

This neon indicator lamp provides a visible signal when its circuit is energized, restoring a clear status light on the appliance's panel. Replace a failed lamp to regain quick, at-a-glance confirmation that a function is active.

• Illuminates when power is supplied to the associated circuit, serving as a panel/pilot indicator
• Helps provide clear visual status for appliance functions
• Typical symptoms: indicator does not light, is dim or flickers, stays on continuously, or shows visible damage
• Can fail open or intermittently, leading to unreliable status indication

• Disconnect power to the appliance before servicing
• Access the control/panel area to reach the lamp; note wire routing and terminal orientation
• Transfer leads and seat the lamp securely; handle components carefully to avoid damage
• If the original is board-soldered, board-level repair may be required.

This rotary switch mounts behind the control knob and reads your selections on the user interface. Replacing a worn switch restores accurate, reliable knob response so the appliance recognizes the chosen setting and relays it to the control board.

• Detects the position of the selector knob and sends the appropriate signals to the main control
• Enables choosing programs/settings using the front knob
• Failure may cause unresponsive or erratic selection, settings not changing when the knob turns, or a no-start if no selection is registered
• Typically located on the back of the control panel behind the knob

• Disconnect power before servicing
• Remove the knob and access the control panel to reach the switch
• Release locking tabs or screws; transfer the wire connector in the same orientation
• Align the shaft correctly with the knob and test operation before reassembly

The Spring is an OEM replacement part for LG ranges. Located within the oven door mechanism, this coiled metal spring helps counterbalance the weight of the door for smooth opening and closing. 

Causes of a bad spring can include fatigue from repeated compression cycles over several years, as well as stretching or damage from forced closure of an overloaded door. 

Symptoms of a bad spring include:

• Difficulty lifting or closing the oven door
• Sagging or misaligned door that doesn't stay shut  
• Loud squeaking or rubbing noises during use
• Broken, loose, or stretched coils losing tension  

This OEM LG part is also compatible with Sears Kenmore ranges and select GE models.

A circular lug designed to join a stripped wire to a threaded terminal for a secure electrical connection. Helps restore reliable contact at terminals and reduces the chance of intermittent power or arcing at connection points. What it does:

• Provides a strong mechanical and electrical connection between a wire and a screw or bolt terminal.
• Helps prevent loose connections that can cause intermittent operation, sparking, or overheating.
• Commonly used where a ring-style termination is required for safe, stable wiring.
• Works with properly sized wire and fasteners to maintain consistent conductivity.

• Always disconnect power to the appliance before inspecting or replacing electrical parts.
• Use the correct lug size and gauge for the wire and terminal; crimp or solder per manufacturer recommendations.
• Tighten terminal hardware to the appliance manufacturer's specified torque; avoid over-tightening which can damage the lug or terminal.
• If wiring insulation or the terminal is damaged or corroded, replace the affected components rather than reusing them.

This upper plate assembly replaces a damaged or worn upper cavity plate to restore proper fit and protection for internal components. It helps maintain appliance performance by securing and covering the upper area inside the unit. What it does:

• Replaces a cracked, bent, or missing upper plate that exposes internal parts
• Helps prevent contact with wiring and components in the upper cavity
• Reduces rattling or movement caused by a loose or damaged plate
• Restores correct alignment of panels or trim that mount to the upper area

• Disconnect power before beginning any repair to avoid shock or injury
• Use appropriate hand tools and avoid forcing fasteners; follow OEM disassembly steps
• Handle edges carefully to avoid cuts; wear gloves if needed

This rear cover replaces the cabinet rear panel to protect internal components and maintain proper airflow. It restores the exterior finish and keeps wiring and mechanical parts shielded from dust and damage. What it does:

• Covers and protects internal components at the appliance rear to prevent accidental contact and debris buildup
• Helps maintain proper airflow routing and component clearance behind the unit
• Restores a finished appearance to the rear of the appliance after repair or part replacement
• Useful when the original rear panel is dented, cracked, or missing

• One rear cover as shown

• Disconnect power (and water if applicable) before starting any repair
• Installation typically requires removing the old rear panel screws and securing this cover with OEM-specified fasteners
• Handle edges carefully and support the cover during installation to avoid scratching or dropping onto internal components

This heater bracket is a metal mounting support that holds the appliance's heater or heating element securely in place, helping maintain proper alignment and reduce movement. Replacing a bent or broken bracket restores stable support for the heater assembly. What it does:

• Secures the heater or heating element to the appliance frame so the element stays aligned and does not contact other components.
• Prevents rattling, shifting, or sagging of the heater assembly that can cause noise or uneven heating.
• Helps maintain safe clearances between the heater and surrounding parts.
• Used when the original bracket is cracked, bent, or missing hardware.

• Disconnect power (and gas, if applicable) before beginning work to avoid electrical shock or gas hazards.
• Handle metal parts carefully — edges may be sharp. Wear gloves and eye protection.
• Match the part number and orientation, secure all fasteners, and ensure the heater is properly aligned before restoring power.

The Oven Rack is an OEM part for LG ranges. This part provides a stable surface for placing cookware during baking, roasting, and broiling.

Causes of a bad oven rack can include exposure to high temperatures over time, which can weaken the metal, or accidental damage that causes bending or warping.  

Symptoms of a bad oven rack include:

• Warping or bending of the rack
• Difficulty sliding the rack in and out of the oven
• The rack not sitting level within the oven

This OEM LG part is also compatible with some Kenmore models.

This small, board-mounted tactile push-button switch is used on the control panel. It registers a momentary press so the control board can accept your selection. Replacing a worn switch restores reliable button response and consistent operation.

• Mounts to the user interface board and provides momentary contact when a button is pressed
• Sends a low-voltage signal to the control, enabling cycle or option selection
• Typical failure symptoms: unresponsive or intermittent buttons, needing extra force to register, stuck/always-on input, or unintended beeps/changes
• Helps restore consistent user-interface input when an individual button switch has failed

• Disconnect power to the appliance before servicing; shut off gas/water if applicable
• Access the control panel to reach the user interface board
• This is a board-level repair; note switch orientation. Replacement may require desoldering/soldering per OEM procedure
• Use ESD precautions and avoid overheating PCB pads; test button function before reassembly

The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.

Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.

Symptoms of a bad magnetron thermostat may include:

• Microwave not heating food evenly or at all
• Inconsistent or weak heating performance
• Microwave shutting off or displaying error codes related to temperature issues

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Thermistor is an OEM replacement part for LG gas ranges. It serves as a highly sensitive temperature sensor mounted inside the oven cavity. 

Symptoms of a bad thermistor include:  

• Inability to select certain cooking modes like bake or convection that involve temperature control
• Fluctuating or inaccurate temperature readouts on oven displays
• Irregular cooking outcomes like hot/cold spots inside the oven
• Repeated error codes regarding temperature sensing issues

Causes can be attributed to prolonged exposures to heat and intermittent combustion byproducts inside the oven. Over a decade of use, these conditions may degrade the thermal and electrical properties of sensor components. 

This genuine LG replacement thermistor installs effortlessly. Installing a new thermistor restores temperature monitoring required for reliable gas oven performance. 

The Motor, AC Fan is an OEM part for LG ovens. This fan motor is responsible for circulating air within the oven cavity, ensuring even heat distribution for consistent cooking and baking results. It helps maintain the oven’s temperature by moving hot air around, which is especially important for convection ovens.

Over time, the fan motor can wear out or become faulty due to continuous use, exposure to high temperatures, or electrical issues. When the fan motor fails, it can lead to uneven cooking and potential overheating of the oven.

Symptoms of a bad oven motor, AC fan include:

• Uneven cooking or baking results
• Unusual noises coming from the oven during operation
• The oven taking longer to preheat
• The fan not spinning or running intermittently
• Error codes related to fan or airflow issues

This OEM LG part is also compatible with Sears/Kenmore models.

A replacement motor bracket that secures the motor to the appliance chassis for stable operation and reduced vibration. Restores proper motor alignment to help maintain smooth, quieter cycles and protect drivetrain components. What it does:

• Holds the motor firmly in place to prevent movement during operation
• Maintains correct motor-to-transmission/gear alignment for reliable power transfer
• Reduces vibration and rattling that can occur when mounts fail
• Helps prevent premature wear of motor and connected components
• Addresses symptoms such as excessive noise, shaking, or motor misalignment

• Disconnect power to the appliance before servicing; follow lockout/tagout best practices
• Turn off water supply and relieve any residual pressure for washer models before disassembly
• Basic mechanical skills and common hand tools required; bracket removal may require loosening motor fasteners and supports
• Reuse OEM fasteners if undamaged and torque to manufacturer specs; inspect surrounding mounts and hardware for wear

This replacement ring secures or positions a nearby appliance component to restore proper alignment and stable operation. It's a small but important part that helps reduce excess movement and related wear. What it does:

• Holds or locates a mating component to prevent unwanted movement or misalignment
• Helps reduce vibration and knocking noises caused by loose parts
• Restores correct spacing that maintains smooth mechanical operation
• Can prevent accelerated wear on adjacent parts when functioning properly

• Disconnect power (and water supply if applicable) before beginning any repair
• Access location may require removing panels or trim; keep fasteners organized
• Inspect surrounding parts for wear or damage and replace if needed

The Convection Fan Blade is an OEM replacement part for LG ovens. It works by circulating hot air throughout the oven, reducing cold spots and promoting consistent temperatures.

Causes of a malfunctioning Convection Fan Blade can be wear and tear from regular use, the accumulation of debris hindering the blade’s rotation, or mechanical issues impacting the fan motor or blade alignment.

Symptoms of a bad Convection Fan Blade include:

• Uneven cooking or baking, leading to partially cooked food
• Noises emanating from the oven during operation, indicating possible damage or obstruction
• The fan not rotating or moving irregularly, signaling mechanical issues

This OEM LG part is also compatible with Sears/Kenmore oven models.

This Fan Blade is an OEM part for LG microwaves. It is a critical component designed to circulate air within the microwave, aiding in heat dissipation and ensuring even cooking. 

Fan blades in microwaves can suffer from wear, imbalance, or damage due to regular use or accumulation of debris. A malfunctioning fan blade can lead to inadequate ventilation, affecting the microwave's cooking efficiency and potentially causing overheating.

Symptoms of a bad fan blade include:

• Unusual noises during operation, such as rattling or buzzing, indicate a loose or damaged blade.
• The microwave overheating or shutting off prematurely.
• Inconsistent cooking or hot spots in food suggest poor air circulation.
• The fan not starting, or stopping unexpectedly during use.
• Visible signs of damage or wear on the blade.

This OEM LG part is also compatible with some Sears/Kenmore models.
 

This AC synchronous motor assembly drives the appliance's rotating components to restore proper operation and consistent performance. It replaces a failed motor to stop stalling, humming or lack of rotation in affected units. What it does:

• Converts electrical input into smooth, synchronous rotational motion for the appliance's driven component
• Stops symptoms like no spin, intermittent rotation, or a motor that hums without turning
• Restores stable, timed movement where a synchronous motor is required
• Interfaces with the appliance's original mounting and wiring harness for direct replacement

• Disconnect power before beginning any repair to avoid electrical shock
• Verify wiring harness orientation and connector seating before applying power
• Inspect mounting points and shaft coupling for wear and secure per OEM guidelines

This incandescent oven lamp provides interior illumination so you can safely check food without opening the door. Direct replacement for a burned or dim oven/range light to restore cooking visibility. What it does

• Replaces a burned-out or flickering oven interior light bulb
• Restores clear visibility of the oven cavity for monitoring cooking progress
• Helps avoid opening the oven door unnecessarily, preserving oven temperature
• Fits the original lamp socket and installs in the oven light housing

• Disconnect power to the appliance before replacing the lamp to prevent electric shock
• Allow the oven and old bulb to cool completely before handling
• Use a cloth or gloves when installing the new lamp to avoid transferring oils from skin

The Broil Element is an OEM replacement part for LG electric ranges. As a vital upper heating system, this broil element helps efficiently brown and crisp foods placed directly under or on the top rack of the oven.

Causes of a defective broil element may relate to normal wear and tear on the coils from repeated high-heat cooking. Food residues adhering over time can reduce performance.

Symptoms of a problematic broil element include:

• Inadequate or uneven browning from the top-level heating system   
• Diminished functionality of the broil setting on the control panel
• Potential thermal damage or exposed wiring from a failed element

This OEM component fits some Kenmore/Sears electric range models as well. 

The Heating Element is an OEM part for LG electric ranges. It serves a critical cooking function by using electric current to generate heat energy that cooks food inside the oven cavity. The heating element is constructed from flame-resistant and durable materials precisely designed to withstand high temperatures in a clean efficient manner.  

Causes of a bad heating element can include mineral deposits on coils, cracks from overheating, or general wear over extended use.

Replacing a faulty element restores dependable oven performance. 

Symptoms of a bad element include:

• Inefficient or uneven cooking temperatures
• Longer baking and cooking times 
• Cracking or sagging coils affecting heat output
• Potential safety issues if damage exposes live wires

This element also fits the heating designs used in Jenn-Air and Frigidaire electric ovens.

The Oven Door Gasket is an OEM part for LG ranges. This seal creates an insulating barrier between the hot oven interior and the external environment. The gasket ensures proper heat retention for energy efficiency and is responsible for safely containing heat inside during baking and broiling. 

Symptoms of a faulty door gasket include:

• Excessive heat loss from the oven that compromises cooking ability
• Discomfort from direct heat around the outer door surface   
• Physical damage or gaps in the insulation compromising its sealing function

Causes of gasket failure involve normal wear and tear from repetitive door openings as well as damage from oven cleaning chemicals or abrasive scrubbing.

This OEM LG part is also compatible with some Kenmore ranges featuring LG oven systems. Replacing the worn gasket restores safe, efficient oven operation.

This outer door frame secures and finishes the refrigerator/freezer door, restoring proper fit and appearance. Replaces a damaged, cracked, or warped frame to help the door seal and close correctly. What it does:

• Provides the structural trim around the door opening and anchors the door panel
• Restores proper alignment and improves door closure when the frame is warped or broken
• Prevents drafts by supporting the door gasket area
• Helps eliminate rattling or loose front panels caused by a damaged frame

• 1 outer door frame

• Disconnect power to the appliance before starting any repairs
• Remove door trim screws and panels carefully to avoid damaging the door or gasket
• Handle the frame and surrounding trim gently to prevent cracking; some clips may be brittle with age

This front plate is the outer panel that restores the appliance's exterior appearance and provides a finished surface for controls and openings. It replaces damaged, dented, or scratched front panels to improve looks and panel alignment. What it does:

• Replaces a cracked, dented, or warped front panel that affects appearance
• Restores proper fit and alignment of control openings and trim
• Helps protect internal components from light bumps and cosmetics damage
• Returns the appliance to a uniform, factory-style exterior

• One front plate

• High-level swap: remove power, detach surrounding trim or control assembly, replace panel, and reassemble; follow manufacturer disassembly order
• Disconnect power before starting. Wear gloves to avoid sharp edges.
• Use manufacturer screws and retainers. Do not force panels; check alignment before tightening.
• If fastening points or clips are damaged, replace them with OEM-specified hardware.

This front panel is the exterior control-panel trim that restores the appliance's appearance and protects the underlying buttons and electronics from everyday wear. It gives a clean, finished look and helps keep controls sealed from spills and debris. What it does:

• Covers and protects the control area and buttons from dirt, moisture, and bumps
• Restores a damaged, cracked, or faded front surface to improve appearance
• Keeps the control electronics accessible while shielding them from direct contact
• Helps the door/control assembly align and fit properly when installed

• One front panel

• Disconnect power before servicing to avoid shock or injury
• Remove any trim screws or snaps holding the old panel; handle clips gently to avoid breaking
• Align panel tabs and secure with original hardware; do not overtighten screws
• Avoid contact with circuit boards and consider an anti-static precaution

This foot is a small rubber base pad that supports and stabilizes the appliance on the countertop or cabinet surface. Replacing a worn or missing foot helps keep the unit level and reduces vibration and slipping.

• Provides stable, non-slip support on flat surfaces
• Helps keep the appliance level for proper operation
• Replaces missing, cracked, or flattened feet
• Can reduce vibration, rattling, or shifting during use

• Unplug the appliance before servicing
• Turn the unit on its side/back for access to the base
• Pull off the old foot and press the new one firmly into place (some models may use adhesive or a tab fit)
• Verify the unit sits level; replace additional feet as needed

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This replacement slider restores smooth, guided movement for the appliance component it mounts to, helping reduce sticking, binding and noise. A simple, low-cost part that returns parts to proper alignment and operation. What it does:

• Guides and supports a moving panel or drawer to ensure even, low-friction travel
• Reduces binding, catching or noisy movement when the original slider is worn or damaged
• Keeps the associated component aligned to prevent uneven wear or mis-tracking
• Helps restore normal operation without replacing larger assemblies

• One replacement slider

• Disconnect power to the appliance before beginning any repair
• Remove the affected panel/drawer per the appliance service instructions to access the slider
• Inspect surrounding tracks or mounting tabs for damage and replace if necessary
• Test movement after installation; if binding persists, re-check alignment

This slider is a replacement glide piece that helps a drawer or sliding compartment move smoothly and stay aligned. Replacing a worn slider restores quiet, consistent travel and prevents wear on the surrounding trim. What it does:

• Guides and supports a drawer or sliding compartment for even movement
• Reduces sticking, scraping, and noisy operation from worn glides
• Keeps the drawer aligned to prevent rubbing or binding against the cabinet
• Helps extend life of associated rails and trim by restoring proper tracking

• One slider glide piece

• Disconnect power to the appliance and remove any contents before servicing
• Remove the drawer or access panel per your appliance instructions to reach the slider
• Inspect mating rail and fasteners; replace any damaged clips or screws for a secure fit

The Foot is an OEM part for LG range ovens. It sits at the base of the range and provides stability, as well as protecting countertops from heat and scratches. 

Symptoms of a faulty foot include:

• Wobbling or unstable range that rocks from side to side 
• Visible wear on the bottoms of the feet
• Countertop surface showing signs of heat damage or scratches below the range

Causes can be general wear over years of use, an impact or blow that warped the footing, or adjustment mechanisms becoming loose.

Replacing your LG OEM foot will restore a sturdy, level foundation for safe cooking. The new feet grip securely without slipping to prevent shifting of heavy appliance weight. This will also protect cabinetry surfaces beneath the range. As an official LG part, it is also compatible with some Sears and Kenmore ovens.