Parts for Frigidaire FGBM19WNVFA: Oven,Cabinet Parts

This replacement cover protects and finishes a specific component area on your appliance. Replacing a cracked or missing cover helps keep out debris, restores proper protection, and maintains a clean, factory appearance.

• Shields the underlying assembly from dust and accidental contact
• Maintains proper enclosure as designed by the manufacturer
• Direct replacement when the original is cracked, warped, or missing
• Typical symptoms include a loose or rattling panel, broken tabs, or exposed parts

• Disconnect power before servicing; also shut off gas/water if applicable
• Note screw/clip locations and orientation for correct reassembly
• Transfer any reusable hardware from the old cover
• Do not overtighten fasteners into plastic to avoid damage

The Shelf Support is an OEM part for Frigidaire countertop microwaves. It holds and stabilizes shelving inside the microwave cavity during operation. 

Symptoms of a faulty shelf support include:

• Loose or detached shelves that cannot maintain placement  
• Difficulty positioning shelves at desired height levels
• Scrapes or dents on interior microwave walls from shelf movement
• Gaps or spaces where shelf legs do not sit securely  

Causes relate to typical wear of spring clips or brackets holding shelves in place. Regular vibration from microwave turntables can weaken pressure points over time.

This OEM replacement shelf is compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Shelf Support is an OEM part for Frigidaire countertop microwaves. It holds and stabilizes shelving inside the microwave cavity during operation. 

Symptoms of a faulty shelf support include:

• Loose or detached shelves that cannot maintain placement  
• Difficulty positioning shelves at desired height levels
• Scrapes or dents on interior microwave walls from shelf movement
• Gaps or spaces where shelf legs do not sit securely  

Causes relate to typical wear of spring clips or brackets holding shelves in place. Regular vibration from microwave turntables can weaken pressure points over time.

This OEM replacement shelf is compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement cover protects internal components and restores the unit's exterior appearance. It replaces a cracked, broken or missing panel to keep wiring and mechanisms shielded and help the appliance look finished. What it does:

• Covers and protects internal components from dust and incidental contact
• Restores a flush exterior surface when an original cover is damaged or missing
• Helps prevent loose wires or controls from being exposed
• Reduces risk of snags or accidental contact with internal parts

• Disconnect power to the appliance before attempting any repair
• Remove any trim or fasteners holding the old cover in place; use appropriate screwdrivers
• Align cover tabs/clips and seat evenly before re-securing fasteners
• Replace damaged clips or mounting hardware before completing installation

This base is the lower cabinet support and trim piece that secures the appliance's kickplate and helps keep the cabinet level and stable. It restores proper fit and prevents debris from collecting under the unit. What it does

• Provides structural support for the appliance's lower cabinet and kickplate
• Secures the toe kick and helps maintain correct appliance clearance
• Helps reduce vibration and movement at the base of the appliance
• Prevents dirt and debris from entering under the cabinet
• Commonly replaced when the lower trim is cracked, broken, or missing

• One base piece as shown

• Disconnect power and water before starting work
• Remove the toe kick/trim and any mounting screws to access the base
• Use basic hand tools; handle edges carefully to avoid cuts

The Grease Filter is an OEM part for Frigidaire microwaves. This part traps grease and other particles generated during cooking, preventing them from accumulating on the internal components and the exhaust system.

Common causes of a bad grease filter include prolonged use without cleaning or replacement, accumulation of grease and food particles, and damage from high temperatures or physical impacts.

Symptoms of a bad Grease Filter include:

• Reduced ventilation efficiency
• Excessive smoke or odors during cooking
• Visible grease buildup on or around the filter
• The filter appearing clogged or damaged

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement frame restores the outer trim around the appliance door to its original fit and appearance, helping keep door components aligned and protecting internal parts from damage. What it does

• Replaces a cracked, warped, or visibly damaged door trim piece
• Secures door glass and inner components in place for proper operation
• Restores a finished look to the appliance front after impact or wear
• Helps prevent drafts and debris from entering around the door edge

• Disconnect power to the appliance before starting any repair
• Remove the door or necessary panels per the service manual to access mounting screws
• Keep track of screws and clips; work on a soft surface to avoid scratching

This transformer supplies low-voltage power to the refrigerator's control circuits so electronic components receive stable power for reliable operation. Replace a failed transformer to restore power to controls and related functions. What it does

• Converts line voltage to low-voltage power used by control boards and electronic modules.
• Commonly linked to symptoms like non-working control displays, no response from dispenser or ice controls, or intermittent electronic behavior.
• Works as a direct replacement part when the original transformer fails or shows electrical faults.
• Designed to mount and wire into the appliance's control compartment per OEM configuration.

• One transformer

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Verify wiring locations and harness orientation before removal; label connectors if needed.
• Use proper tools and follow the appliance's service manual for access and mounting instructions.

This replacement motor restores power to the appliance's fan or blower assembly so airflow and cooling performance resume. Use it to replace a failed or noisy motor and get your appliance running normally again. What it does

• Spins the fan/blower or driven component to circulate air or operate the mechanism.
• Replaces motors that stall, hum, or do not run at all.
• Can resolve reduced airflow, warm compartments, or uneven cooling when motor failure is the cause.
• Designed to match the appliance's original motor function and mounting.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Verify the motor part number and physical fit against the unit before installation.
• Basic hand tools required; access may require removing panels or shelves.

This diode is an electrical rectifier used on refrigerators to allow current flow in one direction and protect circuits from backfeed. Replacing a faulty diode restores proper circuit behavior and helps the appliance run reliably. What it does:

• Allows current to flow in a single direction to protect control and relay circuits
• Prevents backfeed that can damage electronic components
• Can be linked to intermittent operation, failure to start, or control-board-related faults
• Used wherever a single-direction current path or transient protection is required

• High-level replacement; disconnect power at the breaker or unplug the appliance before starting
• Confirm orientation/polarity matches the original during installation
• Use appropriate tools; avoid shorting leads or touching circuit traces

The Thermostat is an OEM part for Frigidaire microwaves. The thermostat accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

The Thermostat is an OEM part for Frigidaire microwaves. Situated near the top of the microwave cavity, it accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

This temperature control thermostat regulates the refrigerator's cooling cycle to help maintain set temperatures in the fresh food compartment. Replaces a failed thermostat to restore proper compressor cycling and temperature control. What it does:

• Senses cabinet temperature and cycles the compressor on and off to maintain the selected setting.
• Stops cooling when the set temperature is reached and restarts cooling as temperatures rise.
• Commonly used when the refrigerator is running constantly, not cooling, or temperatures are inconsistent.
• Works with the control knob/capillary assembly to provide user-adjustable temperature control.

• Disconnect power to the appliance before attempting service.
• Access typically requires removing the control knob and control housing; handle the capillary tube gently to avoid kinks.
• Verify correct replacement location and routing before reassembly; test operation after restoring power.

This mechanical thermostat controls refrigerator temperature by sensing evaporator or cabinet temperature and switching the compressor and fans on and off. Replaces a worn or faulty control to help restore consistent cooling and temperature regulation. What it does

• Senses temperature and closes/open circuit to run the compressor and cooling fans
• Helps maintain set temperature by cycling refrigeration system components
• Commonly linked to symptoms like warm or fluctuating temperatures, compressor not running, or continuous running
• Works as the control point for user temperature settings

• One thermostat

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Access may require removing interior panels or control housing
• Handle sensing bulb and capillary tube carefully to avoid kinks or damage

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

This capacitor helps the refrigerator compressor start and run smoothly, restoring reliable motor operation and improving cooling performance when the original capacitor fails. It's a direct-replacement electrical component used on compatible Frigidaire appliances. What it does:

• Supplies the brief electrical boost the compressor motor needs to start
• Supports continuous motor operation to maintain consistent cooling
• Commonly linked to symptoms such as the compressor struggling to start, loud humming, or reduced cooling
• Helps prevent hard starts that can lead to overheating or repeated cycle failures

• One capacitor

• Disconnect power to the appliance before service to avoid electric shock
• Capacitors can hold a charge—discharge safely before touching terminals
• Verify terminal connections match the original and secure all wiring after replacement

This evaporator fan motor circulates cold air through the freezer and refrigerator compartments to maintain even cooling. Replacing a failed fan motor restores proper airflow and helps prevent temperature drift and frost buildup. What it does:

• Spins the evaporator fan blade to move cold air across the evaporator coil and into the cabinet.
• Supports even temperature distribution between freezer and fresh-food sections.
• Common symptom link: cabinet running warmer or uneven temperatures.
• Common symptom link: excessive noise or a fan that does not spin.

• Disconnect power to the appliance before servicing to avoid electric shock.
• Handle the motor and fan blade carefully to avoid bending the blade or damaging the shaft.
• Secure all fasteners and harnesses.
• After installation, restore power and confirm the fan runs quietly and that airflow is restored.

The fuse is a protective link in the appliance's power circuit. When excessive current or a short is detected, it opens the circuit to help safeguard wiring and electronics. A blown fuse often leaves the unit completely unresponsive.

• Interrupts power during an overcurrent or short to prevent further damage
• Helps protect control boards, motors, and wiring
• Typical symptoms: no power, blank display/controls, won't start
• Tests open (no continuity) when blown

• Disconnect power at the breaker or unplug before servicing
• Replace only with the same type and rating specified by the manufacturer
• If a new fuse blows again, locate and correct the underlying short or failed component before further use
• For microwave repairs, high-voltage capacitors can retain a dangerous charge.

This replacement refrigerator water filter cartridge helps restore clean tasting water and ice by trapping common impurities. Designed as a direct-fit replacement to maintain your fridge's filtered water supply and improve taste clarity. What it does:

• Filters particulates and common contaminants to improve water and ice taste
• Helps reduce visible sediment and cloudiness from the dispenser and ice maker
• Restores normal dispensing performance when an old filter causes off-flavors or odors
• Supports consistent filtered water flow when installed and maintained

• Turn off the water supply and follow the refrigerator's filter-replacement instructions before starting
• Push/rotate or slide per your model's procedure until the filter locks in place; ensure a secure seal
• Run water through the dispenser for a short time after installation to flush air and initial carbon fines
• Replace regularly per the refrigerator manufacturer's recommendation or sooner if flow decreases or taste returns

The Lamp is an original and genuine OEM replacement part for Frigidaire microwaves. It is located inside the microwave and provides light to easily see food and monitor cooking progress.

Causes of a bad lamp can be natural bulb burnout over time, damage from foods accidentally jostling the lamp during cooking, or general wear and tear.

Symptoms of a bad lamp include:

• Dimming or flickering light inside the microwave when in use
• No light turning on when the microwave is powered on
• Broken or cracked bulb housing

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Switch is an OEM part for Frigidaire microwaves. It plays a crucial role in the microwave's overall function by detecting when the door is open or closed. The door switch communicates this information to the control board, enabling it to safely operate the microwave's electronic components and magnetron when the door is shut.

Symptoms of a bad door switch include:

• The microwave failing to operate or function properly with the door closed  
• Inability to start or pause operation when the door is opened
• Error codes or failure messages appearing on the display related to door functionality

Causes of a bad door switch can be wear and tear over time, damage from repeated opening and closing of the microwave door, or impact from accidental mishandling. 

This OEM replacement is also compatible with Electrolux, Admiral, Crosley, White-Westinghouse, and Kenmore models.
 

This infinite switch controls the heat level for an electric cooktop surface burner, restoring adjustable power to the element for even cooking and reliable temperature selection. What it does:

• Regulates electrical power to a single surface heating element so you can set low-to-high heat.
• Provides stepped "infinite" control positions rather than a simple on/off.
• Replaces a worn or failed control that causes a burner to not heat, stay stuck on one setting, or heat inconsistently.
• Uses standard spade-terminal connections found on many electric ranges.

• Disconnect power at the breaker before servicing—this part services live-voltage circuits.
• Access typically requires removing the cooktop or rear console; handle ceramic glass cooktops carefully to avoid cracking.
• Confirm terminal layout and mounting orientation before removal; take a photo of wiring for reassembly.

The Door Switch is an OEM part for Frigidaire microwaves. It plays a crucial role in the microwave's overall function by detecting when the door is open or closed. The door switch communicates this information to the control board, enabling it to safely operate the microwave's electronic components and magnetron when the door is shut.

Symptoms of a bad door switch include:

• The microwave failing to operate or function properly with the door closed  
• Inability to start or pause operation when the door is opened
• Error codes or failure messages appearing on the display related to door functionality

Causes of a bad door switch can be wear and tear over time, damage from repeated opening and closing of the microwave door, or impact from accidental mishandling. 

This OEM replacement is also compatible with Electrolux, Admiral, Crosley, White-Westinghouse, and Kenmore models.
 

This replacement electrical wire harness routes power between components so your appliance can run reliably. It restores connectivity for circuits affected by damaged or worn wiring. What it does

• Carries electrical current between internal components to restore power and signal continuity.
• Replaces frayed, cut, or burnt wiring that can cause intermittent operation or component failure.
• Helps eliminate arcing, visible burn marks, or loose-disconnect issues at terminals.
• Matches original connector types and color-coded leads for a straightforward swap.

• Always disconnect power before starting any repair to avoid shock or injury.
• Verify connector orientation and wire colors match the original before finalizing connections.
• Route and secure the harness away from moving parts and hot surfaces to prevent wear.

This is a stamped metal mounting bracket that secures internal components to the appliance frame, restoring proper alignment and support for affected assemblies. Replace a damaged or missing bracket to stop movement and maintain structural fit. What it does:

• Secures internal panels or assemblies to the cabinet to prevent shifting or vibration
• Restores correct alignment for attached components, helping reduce rattling or misfit
• Maintains stable mounting for controls, trim, or wiring harnesses that rely on frame attachment
• Works where a bent, cracked, or missing bracket causes loose parts or improper clearances

• Typical install requires basic hand tools; disconnect power before starting
• Inspect surrounding fasteners and mating surfaces; replace any damaged screws or clips
• Reinstall carefully to avoid bending the bracket; verify secure fit and component alignment

This replacement lever restores reliable manual control of the appliance component it attaches to, letting the door, dispenser or mechanism operate smoothly and predictably. Durable molded construction resists wear from normal use. What it does

• Replaces a broken, cracked or worn lever that no longer engages or pivots correctly
• Restores proper mechanical linkage so doors, latches or dispensers can open and close as intended
• Prevents slipping, binding or intermittent operation caused by damaged lever geometry
• Matches the OEM shape to fit mounting posts and pivots without modification

• One replacement lever

• Disconnect power (and water if applicable) before starting any repair
• Remove the panel or housing that covers the lever mounting area to access fasteners and clips
• Keep small screws and clips organized; lever typically secures on a post or with a retaining clip

This replacement lever restores the original lever action so your appliance opens, closes or engages controls smoothly. It's a direct-fit part that replaces a cracked, worn or broken lever to regain normal operation. What it does:

• Replaces a damaged lever that prevents a door, latch or control from operating properly
• Provides a secure pivot or release point so components engage and disengage as intended
• Common symptom fixes: lever broken, loose, stuck, or not engaging reliably
• Durable plastic construction matches the OEM fit and alignment

• Disconnect power or unplug the appliance before starting any repair
• Remove any nearby panels or fasteners to access the existing lever; retain screws for reassembly
• Align the new lever on its pivot, then snap or fasten it into place without forcing parts

This is a replacement tension spring that restores proper tension and movement on compatible Frigidaire appliance components. It helps the mechanism operate smoothly and reduces sagging, binding, or uneven motion. What it does:

• Provides tension for hinge or linkage assemblies so doors or moving parts return and stay aligned
• Restores smooth, controlled movement and reduces slapping or sudden drops
• Helps prevent binding or uneven operation caused by a weakened or broken spring
• Commonly used where a small coil spring is required to maintain part position or preload

• One tension spring

• Disconnect power and remove food/items before accessing appliance interiors or doors
• Use gloves and eye protection; springs can be under tension and may release suddenly
• Note spring orientation and attachment points before removal so reassembly matches OEM positioning

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged

The Vent Damper is an OEM part for Frigidaire microwaves. It is designed to control the flow of air through the microwave’s ventilation system, ensuring proper ventilation during operation. This component helps to prevent the backflow of air, keeping the microwave's interior and its surroundings free from unwanted odors and heat.

Causes of a bad vent damper can include wear and tear over time, accumulation of grease or debris, or damage from external impact. 

Symptoms of a bad vent damper include:

• Poor ventilation
• Unusual odors lingering around the microwave
• Excessive heat buildup
• Increased noise during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Damper is an OEM part for Frigidaire microwaves. This part regulates airflow within the microwave, ensuring that steam and odors are properly vented out during cooking.

Causes of a bad damper can include wear and tear over time, buildup of grease and debris, or damage from high temperatures.  

Symptoms of a bad Damper include:

• Poor ventilation during cooking, leading to lingering odors and steam
• The microwave overheating or not ventilating properly
• Unusual noises coming from the damper area
• The damper not opening or closing as it should

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Coupler is an OEM part for Frigidaire microwaves. It connects the microwave glass tray to the rotating turntable shaft inside the microwave. The coupler allows for the stable and secure rotation of the glass tray when in use, ensuring even cooking and heating.

Causes of a bad coupler can include wear and tear over time if utilized excessively, as well as damage due to impact or stress placed on the coupler during mishandling or cleaning of the tray.

Symptoms of a bad coupler include:

• The glass tray not spinning or rotating properly during cooking
• Excessive shaking or vibration of the tray
• Detachment or separation of the tray from the turntable shaft
• Leakage or drips occurring near the tray connection point

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Support Ring is an OEM part for Frigidaire microwaves. This support ring is an integral component that sits beneath the microwave's turntable, providing stable and balanced support. It ensures the smooth rotation of the turntable, which is essential for even cooking and heating food. 

The support ring can become worn or damaged due to regular use, leading to issues with the turntable's rotation. Common causes of deterioration include mechanical stress, uneven weight distribution from dishes, or accidental damage.

Symptoms of a faulty support ring include:

• Unsteady or wobbly turntable movement.
• The turntable struggling to rotate or not rotating at all.
• Noises such as scraping or clicking when the microwave is in operation.
• Uneven cooking or heating of food, indicating a disruption in turntable motion.
• Visible cracks, breaks, or warping of the support ring.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This glass turntable tray sits on the microwave's roller support to provide a stable, rotating surface for even heating. Replacing a cracked or missing tray restores safe operation and helps keep spills contained for easier cleanup.

• Provides a flat, heat-resistant surface for dishes and cookware
• Engages the center coupler to rotate food for more uniform cooking and defrosting
• Removes easily for cleaning and helps contain minor spills
• Common symptoms: cracked/chipped glass, wobbling, won't sit level, or tray no longer rotates due to a worn hub

• Unplug the microwave or switch off the circuit breaker before service
• Remove the old tray; wipe the roller ring and cavity floor clean
• Inspect the center coupler and roller ring for wear; replace if damaged
• Align the new tray with the coupler so it sits flat and turns freely; test with a microwave-safe cup of water

This replacement cover is a molded protective housing that shields internal appliance components from dirt and accidental contact, helping keep parts secure and maintain safe operation. What it does:

• Protects internal wiring, connectors, or small components from dust and debris
• Helps prevent accidental contact with components while servicing or using the appliance
• Keeps parts held in place to reduce rattles or movement
• Restores missing or cracked covers that expose internal areas

• Disconnect power to the appliance before beginning any work
• Typically installed with a few screws or clips after removing the access panel
• Handle gently to avoid snapping mounting tabs; replace any damaged fasteners

This replacement grill restores the appliance's front vent trim and appearance while helping keep the vent opening protected from debris. Use it to replace cracked, broken, or visibly worn grills that rattle or look damaged. What it does

• Covers the front vent/air opening and provides a finished trim around the area
• Helps keep debris and small objects out of the vent opening
• Replaces cracked or broken grills that can cause rattling or loose fit
• Restores a consistent, finished appearance to the appliance front

• Disconnect power (or gas supply where applicable) before servicing the appliance.
• Many grills secure with screws or snap-in tabs behind the lower access panel or oven door; remove panels carefully to reach mounting points.
• Handle mounting tabs gently to avoid breaking them during removal or installation.

The Mounting Bracket is an OEM part for Frigidaire microwaves. This part securely attaches the microwave to the wall or cabinetry. This bracket is designed to ensure that your microwave is mounted safely and remains stable during operation, preventing any potential movement that could lead to damage or operational issues. 

Causes of a bad Mounting Bracket can include physical damage from improper installation or accidents, wear and tear over time that weakens the bracket's integrity, and corrosion due to exposure to moisture or kitchen vapors, which can compromise its strength and stability.

Symptoms of a bad Mounting Bracket include:

• The microwave tilting or sagging
• Unusual vibrations or noise during operation, indicating that the microwave is not securely fastened
• Visible damage or rust on the bracket itself, which could weaken its support

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Mounting Kit is an OEM part for Frigidaire microwaves. It provides the necessary hardware to mount a built-in microwave securely above a cooktop or range. The mounting kit contains mounting brackets, and screws to facilitate a safe and sturdy installation. This kit does not include the installation instructions.

Causes of a bad mounting kit can include deterioration of mounting brackets or screws over time and repeated use, or if the original kit was missing components needed for a secure installation.

Symptoms of a bad or missing mounting kit include:

• The microwave become loose or detached from the wall
• Screws fall out or strips during installation
• Brackets bend or break over time
• Microwave is not level after installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Keep your microwave's ventilation performing its best. This replacement air filter helps screen cooking vapors before the air is recirculated or exhausted, restoring proper airflow and helping maintain cleaner, more effective ventilation.

• Filters air drawn through the microwave's ventilation system during cooking
• Helps reduce cooking odors and airborne particles in the exhaust stream
• Supports proper airflow and fan performance for effective venting
• Replace when saturated, damaged, or visibly dirty; do not operate without required filters
• Common signs of a spent filter: persistent odors, weaker ventilation, or a discolored/brittle filter

• Disconnect power by unplugging the unit or switching off the circuit breaker before service
• Access the filter from the underside panel or top/front grille, per your model
• Note the old filter's orientation; install the new filter the same way and secure any tabs or screws
• Ensure all panels/grilles are reinstalled securely before restoring power