Parts for Ge AVM4160DF2BS: Oven Cavity Parts

Microwave sparking or arcing? This waveguide cover shields the magnetron from food debris and prevents damage. Simple DIY repair in minutes.

Replace your cracked, broken, or warped microwave glass turntable tray. This rotating glass plate sits on the turntable support for even cooking.

Replace your microwave's turntable support ring if cracked, broken, or worn. This rotating ring assembly sits beneath the glass tray on small rollers.

Turntable stopped rotating? This microwave turntable coupler connects the motor to the glass tray. Simple pull-up removal makes this a quick DIY fix.

If your microwave turntable won't spin or makes grinding noises, the turntable motor likely failed. Simple fix with basic screwdriver work.

Holds the light bulb in your microwave. Replace if bulbs keep blowing, socket is cracked, or light won't work. Confirm fit with your model number.

Absorbs odors and filters grease from microwave exhaust. Replace when air quality diminishes or every 6 months. Verify fit with your model number.

Microwave won't power on after overheating? This thermal cutoff thermostat prevents damage by shutting down at unsafe temperatures. DIY repair.

Replace your microwave's cavity lamp cover if cracked, discolored, or missing. Protects the interior light bulb from grease and moisture. Confirm fit with your model number before ordering.

If your microwave won't turn on, trips the circuit breaker, or has an electrical smell, the fuse may be blown. Quick fix behind the control panel.

Suppresses electrical interference on your microwave's power line. Replace if cracked, damaged, or missing to reduce hum and radio-frequency noise.

Fix a microwave that won't start or hums without spinning. This motor capacitor restores proper motor operation and reduces startup strain on your appliance.

Fix poor ventilation or excessive moisture in your microwave. This vent motor circulates air and removes heat, odors, and steam from your kitchen.

Air bracket for microwaves. Secures internal airflow components. Replace if bracket is cracked, bent, broken, or missing to restore proper assembly.

Latch bracket for microwave door interlock switches. Mounts behind the control panel to hold door safety switches. Replace if cracked or broken.

If your microwave stays on with the door open or won't power on when closed, this interlock switch lever may be faulty. Simple mechanical repair.

Microwave tripping breaker when you press start? A faulty door switch often causes this. DIYers report success replacing switches in under an hour.

Microwave tripping breaker when door opens or at startup? A failed monitor switch with welded contacts is the likely cause. 30-minute DIY repair.

Microwave tripping breaker when door opens or at startup? A failed monitor switch with welded contacts is the likely cause. 30-minute DIY repair.

Fixes microwave overheating or not heating issues. This thermostat monitors internal temperature and signals controls. Simple repair for most DIYers.

Microwave not heating or heating unevenly? This magnetron generates the energy that warms food. Moderate DIY repair restores consistent performance.

Covers and protects the vent opening on your microwave. Replace if cracked, broken, or missing to maintain proper airflow and prevent debris entry.

Mounting hardware kit for securing your microwave during installation. Includes brackets and fasteners needed when original components are missing or damaged.

Replace your burnt-out microwave light bulb to restore bright interior and cooktop lighting. 30-watt incandescent bulb fits multiple models.

This is a self-tapping ST4-20 screw used to secure printed wiring boards, control panels and small appliance assemblies. It restores proper fastening and helps eliminate loose panels, vibration noise, or intermittent board contact. What it does:

• Secures printed wiring boards (PWB) and control modules to chassis or mounting standoffs
• Helps prevent board movement that can cause intermittent electrical contact or control faults
• Keeps panels and trim fastened to reduce vibration or rattling during operation
• Suitable where a self-tapping sheet-metal style screw is specified

• One ST4-20 self-tapping screw

• Disconnect power before servicing electrical components
• Use the correctly sized Phillips driver and apply steady pressure to avoid cam-out
• Do not overtighten; stop when the screw is snug to avoid damaging PCB or plastic parts
• Replace only with the specified screw to ensure proper fit and grounding where required

Mounting screw for microwaves. Secures internal components or cabinet installation brackets. Replace if stripped, missing, or damaged during repairs.