Parts for Ge CVM721M2N1S5: Oven Cavity Parts

Protects the microwave's waveguide opening from food splatter and grease. Replace when discolored, burned, or damaged to prevent arcing. Verify fit.

This base plate provides a stable mounting surface that secures and supports lower cabinet components on the appliance, helping maintain proper alignment and reduce vibration. Replace a damaged or corroded plate to restore solid support. What it does:

• Secures and supports lower-frame components and brackets to the appliance cabinet
• Helps keep internal components aligned and reduces vibration or rattling
• Prevents further wear from a bent, cracked, or corroded base area
• Common symptom: visible damage, loose panels, or increased vibration/noise from the lower cabinet

• Disconnect power and, if applicable, water supply before beginning any repair
• Remove exterior kick plate or access panels to reach mounting area; keep all fasteners for reuse unless damaged
• Verify correct orientation and tighten fasteners to secure plate without overtightening

Microwave not heating food? This magnetron generates microwave energy to heat and cook. Restores heating in countertop and over-the-range microwaves.

Microwave not heating? The high-voltage transformer supplies power to the magnetron for heat generation. Restores proper cooking performance.

Replace a faulty high voltage capacitor if your microwave won't heat food properly. This capacitor stores electrical energy for the magnetron circuit.

Microwave not heating? This high voltage diode converts AC to DC power for the magnetron. Common failure point. Moderate difficulty repair in 30-45 minutes.

Suppresses electrical interference on your microwave's power line. Replace if cracked, damaged, or missing to reduce hum and radio-frequency noise.

If your microwave won't turn on, trips the circuit breaker, or has an electrical smell, the fuse may be blown. Quick fix behind the control panel.

Fix inconsistent humidity readings in your microwave with this humidity sensor. Measures moisture levels to regulate climate-sensitive features.

Fixes microwave overheating or not heating issues. This thermostat monitors internal temperature and signals controls. Simple repair for most DIYers.

Microwave tripping breaker or won't heat? This thermal cutoff thermostat monitors temperature to prevent overheating. Straightforward replacement.

Microwave tripping the breaker or won't power on? This thermostat protects against overheating. Common fix when the unit is dead. Moderate DIY repair.

Fix a microwave that won't start or hums without spinning. This motor capacitor restores proper motor operation and reduces startup strain on your appliance.

Fix a microwave door that won't latch or close securely with this door latch support. Guides and secures the latch mechanism for proper door closure.

If your microwave stays on with the door open or won't power on when closed, this interlock switch lever may be faulty. Simple mechanical repair.

Microwave tripping breaker when you press start? A faulty door switch often causes this. DIYers report success replacing switches in under an hour.

Microwave tripping breaker when door opens or at startup? A failed monitor switch with welded contacts is the likely cause. 30-minute DIY repair.

Microwave tripping breaker or won't start? Failed door interlock switch is the likely cause. DIY repair in 30-60 minutes with basic tools.

Replacement glass bracket for microwave ovens. Secures glass turntable tray in place. Replace if cracked, broken, or missing to properly support tray.

Captures grease and airborne particles from cooking to maintain exhaust efficiency. Replace when discolored or clogged. Verify fit with your model number.

Mounting hardware kit for securing your microwave during installation. Includes brackets and fasteners needed when original components are missing or damaged.

If your microwave turntable won't spin or makes grinding noises, the turntable motor likely failed. Simple fix with basic screwdriver work.

Microwave won't spin or agitate? A worn shaft coupler fails to transfer torque between motor and turntable. Direct-fit replacement restores rotation.

Replace your microwave's turntable support ring if cracked, broken, or worn. This rotating ring assembly sits beneath the glass tray on small rollers.

Glass turntable tray for microwave ovens. Installs on rotating support ring inside microwave cavity. Replace if cracked, chipped, broken, or missing.

Fix uneven heating in your microwave with a new stirrer shaft. This part distributes microwaves evenly throughout the cavity for consistent cooking results.

Replacement stirrer cover for microwave ovens. Covers the stirrer fan blade inside the cooking cavity. Replace if cracked, broken, or missing.

If your microwave oven isn't venting properly or cooking unevenly, a faulty damper may be restricting airflow. This vent damper assembly restores ventilation.

Secures the air damper assembly in your microwave, keeping it aligned for proper venting. Replace if bracket is cracked, broken, or causing loose damper.

Mounting nut assembly that secures microwave components to studs or brackets. Replace if cracked, stripped, or missing to restore stable panel attachment.

Metal mounting plate that secures built-in microwaves above the range. Replace if cracked, bent, or causing loose fit that allows the unit to shift.

Fix uneven heating or loud operation with this microwave fan assembly. Includes motor and blade for complete airflow restoration in one unit.