Kenmore Compactor 665.7342905 (6657342905, 665 7342905) Parts

• Compactor ram gets stuck
• Noisy

The compactor failed with the ram down, so the drawer wouldn't open which in turn made the mounting brackets inaccessible. This necessitated sliding a thin oscillating saw blade between the cabinet face frame and the counter top to cut through the brackets. It was then possible to roll the unit out and place it on its side. I removed the five screws holding the bottom pan in place, dropped the pan exposing the gear/chain train. The large gear was cracked from shaft out to the edge. One of... Read more

Replaced It With New One Read more

Touch up paint Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

Rood Cause #1: One of the front roller bearings was worn out and did not spin freely. Solution #1: I replaced the two front roller bearing assemblies (both included 2-pack). Rood Cause #2: The bottom surface of the compactor slide-out assembly had become deformed (convex) most likely due to the repeated force of compaction over the years. This bottom surface rubbed against the lower frame as evidenced by removal of paint (bare metal was exposed). Friction prevented the compactor drawer... Read more

Replaced the motor with a direct replacement part. The wiring was not the same because the switch on the motor was different. The instructions that came with the motor were enough for me to figure out what to do. Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

Ordered the part, which arrived incredibly fast and switched out old one for the new. Read more

Bot both sets of roller bearings, lower ones on the appliance and the set on the trash can that rolls out. I just followed the instructions that were in the roller bearing package and only needed the tools that are recommended. Was a little tricky with the nuts, really need a person with "small" fingers to reassemble the nuts back on the lower set of bearing that are on the appliance. All in All, went well and works. Found that the new bearings are v. tight on the machine, being new, so, use... Read more

Replace element Read more

This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more

I bought new thrust races, a drive gear kit, bearings and a sprocket. When the bearing went out, the thrust races, washers, one bottom plate, and a sprocket was eaten up by the the chain due to the slack being created. I followed the video for the Drive Gear Kit repair and everything went together well. I did have to remove the tracks from inside the compactor in order to remove the cardboard liner that "hides" the drive rods. Additionally, be careful to not over-tension the chain when... Read more

After I was shocked at the price to replace the trash compactor, I was happy to find that the parts, both front & back rollers and the handle, were available from AppliancePartsPros.com. They arrived as scheduled and after viewing two videos, the job went very smooth. I hope it puts another 27 years life into the unit. Read more

Replaced broken parts Read more

I bought new thrust races, a drive gear kit, bearings and a sprocket. When the bearing went out, the thrust races, washers, one bottom plate, and a sprocket was eaten up by the the chain due to the slack being created. I followed the video for the Drive Gear Kit repair and everything went together well. I did have to remove the tracks from inside the compactor in order to remove the cardboard liner that "hides" the drive rods. Additionally, be careful to not over-tension the chain when... Read more