Kenmore Dryer 110.73932101 (11073932101, 110 73932101) Parts

Push-in.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This small retaining clip secures the door hinge in place so the door opens and closes smoothly and stays properly aligned. Replacing a worn or missing clip helps restore reliable hinge support and consistent door operation.

• Retains the hinge/hinge pin to prevent shifting or separation
• Helps maintain door alignment to avoid rubbing, sagging, or binding
• Replaces a clip that is bent, cracked, corroded, or missing
• Common signs it's needed: loose or wobbly door, difficulty closing, misaligned door, visible damaged/missing clip

• Unplug the appliance and, if applicable, remove items from the door to reduce weight
• Support the door before working on the hinge
• Remove any hinge cover/fasteners, swap the clip, and ensure it seats fully
• Reassemble and check door alignment and smooth operation

This is a mechanical defrost timer that controls the automatic defrost cycle of the refrigerator. It periodically shuts off the compressor and energizes the defrost heater so frost can melt, helping maintain proper cooling performance.

• Cycles the unit between cooling and defrost at set intervals
• Stuck or failed timers can cause warm temperatures, heavy frost, or continuous running
• Can also cause short-cycling or no-cool if contacts fail

• Disconnect power before servicing
• Access is typically from the control housing or rear service area; note wire positions before removal
• Replace one-for-one with the same terminal orientation; do not force the cam
• After install, allow one full cycle to verify defrost operation

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

A replacement front drum bulkhead that supports the dryer drum and helps keep the front bearing and seal aligned for smooth rotation. Use this bulkhead to restore proper drum alignment and reduce rubbing, noise, and excessive front play. What it does:

• Supports the front of the dryer drum and centers the front bearing/seal for stable rotation.
• Helps prevent drum rub, scraping noises, and uneven wear caused by a misaligned front support.
• Used when the front drum shows excessive play, thumping, or visible damage to the front support area.
• Installing a new bulkhead is commonly done alongside inspection of rollers, bearings, and the drive belt to ensure full drum stability.

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any service.
• Remove the front panel and drum to access the bulkhead; expect sharp edges and tensioned components—wear gloves and eye protection.
• Transfer any existing seals, bearings, or retainers only if undamaged; replace worn fasteners and inspect rollers/belts while the dryer is open.

This door spring counterbalances your dishwasher door so it opens and closes smoothly without slamming. Replacing a fatigued or broken spring restores proper tension and helps protect the hinges and latch.

• Provides counterbalance tension to the door through the hinge mechanism
• Helps the door open and close with controlled movement and stay in position
• Symptoms of failure can include a door that drops quickly, feels heavy, or won't stay put
• May also cause popping/squeaking noises or uneven action on one side of the door

• Disconnect electrical power and turn off the water supply before servicing
• Remove the toe panel/kick plate to access springs near the hinges
• Carefully relieve and reattach spring tension; wear gloves and eye protection
• Ensure both sides are tensioned evenly after replacement

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

The lid switch lever connects the washer's lid hinge to the lid switch, signaling when the lid is closed so the cycle can run. A damaged lever can prevent the safety interlock from closing, leading to no-start or spin issues. What it does:

• Transfers lid movement at the hinge to the lid switch actuator
• A closed lid so the washer can operate
• Common symptoms of a failed lever: washer won't start; won't spin; cycle pauses because the lid-closed signal isn't detected

• 1 lid switch lever

• Disconnect power before servicing
• Lift or open the top to access the hinge/switch area; locate the lever near the lid switch
• Remove the old lever and install the new one in the same orientation; free movement
• Close the lid by hand and the switch clicks before reassembly and testing

This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:

• Provides a clean, finished edge and covers sharp cabinet/console edges
• Helps keep adjacent parts aligned and secured around the opening
• Restores appearance when original trim is cracked, warped, discolored, or missing
• Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts

• 1 trim piece

• Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
• Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
• Transfer any reusable clips/inserts from the old trim to the new part.
• Align and snap/screw the new trim into place; do not overtighten.

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

For mating terminal use [AP31136300].

This out exhaust pipe directs a dryer's exhaust airflow from the appliance to the home vent, helping remove moisture and lint from the dryer cabinet. Durable replacement for worn or damaged exhaust tubing. What it does:

• Channels hot, moist air from the dryer to the external vent to prevent moisture buildup
• Helps maintain proper airflow for efficient drying and reduces lint accumulation inside the cabinet
• Replaces cracked, crushed, or disconnected exhaust connections that cause poor venting or air leaks
• Works as a direct-fit plumbing piece when original exhaust piping is damaged

• One out exhaust pipe

• Disconnect power to the appliance before installing; for gas dryers, turn off gas supply and pilot per manufacturer instructions
• Ensure the pipe fits securely to the dryer outlet and the wall vent; use manufacturer-recommended clamps or fasteners
• Inspect and clean the vent path and lint screen while replacing the pipe to ensure safe airflow

Replacement end cap that restores the appliance's finished edge and helps protect internal components from debris. A simple, low-cost repair to replace cracked, broken, or missing end caps and reduce trim wear. What it does:

• Covers and protects an exposed edge or end of the cabinet/trim.
• Helps prevent snagging, dirt buildup, and contact damage where the cap is missing or cracked.
• Restores the appearance and alignment of surrounding trim pieces.
• Common symptom: visible crack, loose or missing trim, rubbing or catching at the edge.

• Disconnect power and/or water supply to the appliance before beginning work when applicable.
• Inspect the mating surface and remove old adhesive or fasteners before installing the replacement cap.
• Install by aligning the cap and snapping or fastening into place; do not force—use correct fasteners if applicable.
• If surrounding trim is damaged, consider replacing affected pieces to ensure proper fit and finish.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test