Kenmore Washer Dryer Combo 110.88732796 (11088732796, 110 88732796) Parts

This Heater Housing is the metal enclosure that supports the heating element and thermostats and channels airflow through the heater. Replacing a warped, burned-through, or corroded housing helps restore safe, consistent dryer heat and airflow.

• Holds the heating element securely and isolates it from the cabinet
• Directs air across the element for efficient, even heating
• Provides mounting points for high-limit/cycling thermostats and thermal cut-off
• Helps with symptoms such as weak/no heat, scorching in the heater area, repeated element shorts, or visible damage/rust to the housing

• Disconnect power and pull the dryer forward for access
• Remove the rear panel and exhaust duct to reach the heater assembly
• Note wiring; transfer the heating element and thermostats from the old housing to the new one using existing hardware
• Ensure the element is centered and not touching the housing before reassembly; reconnect and test for proper heat and airflow

This heating element generates the heat your electric dryer needs to dry laundry. Replacing a failed element restores consistent temperatures and helps resolve no-heat or long dry-time issues.

• Converts electrical energy into heat inside the dryer's heater assembly
• Typical symptoms of failure: runs but no heat, takes too long to dry, or clothes remain damp
• Visual clues can include a broken/burned coil or an open-circuit continuity test
• Restores proper drying performance when the original element has burned out

• Disconnect power before servicing; heating components operate at high voltage
• Access the heater assembly; note wiring and component positions for reassembly
• Handle the element carefully to avoid stretching or deforming the coil
• After replacement, clean the exhaust duct and check related thermostats/thermal cutoffs for continuity if heat issues persist

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.

This drain hose routes water from the drain pump out of the appliance during the drain cycle. Replacing a worn hose helps the unit empty properly and reduces the risk of leaks or water damage. What it does:

• Carries wastewater from the pump outlet to the household drain path
• Provides a sealed flow path to help prevent leaks and backflow
• Replace if cracked, brittle, swollen, kinked, or internally clogged
• Help resolve symptoms like standing water, slow/no drain, water on the floor, or a "long drain" error

• 1 drain hose

• Unplug the appliance and turn off water supply before service
• Expect residual water; use towels or a shallow pan
• Release and reinstall hose clamps securely; ensure full seating on fittings
• Route to avoid kinks or sharp bends; run a test drain and check for leaks

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

This is the washer's water level pressure switch. It senses the tub's water level and tells the control when to start/stop filling and when to advance the cycle. Replacing a failing switch restores accurate fill levels and reliable cycle progression. What it does:

• Monitors tub water level via air pressure through the attached hose
• Opens/closes the inlet valve circuit to stop or start water fill
• Signals the timer/control to advance to wash, rinse, and spin at the correct level
• Common failure symptoms: overfilling or won't stop filling, won't fill, cycle won't advance, or won't agitate/spin

• 1 water level pressure switch

• Disconnect power and shut off water before servicing
• Lift/remove the control console to access the switch
• Label and transfer wires; move the pressure (air dome) hose to the new switch and ensure a snug, unkinked connection
• Inspect the hose for cracks, kinks, blockages, or water inside; reassemble and run a test fill to operation

Includes drive tube spacer, "T" bearing and both shaft seals.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

This small spring-tension retainer secures a part, bracket, or panel on the appliance. Replacing a worn or missing clip restores a tight fit, reduces rattles, and keeps the assembly correctly positioned during normal operation.

• Provides spring tension to hold mating parts, brackets, or panels in place
• Helps prevent movement and vibration that can cause noise or misalignment
• Common failure signs: loose or wobbly component, rattling, missing/damaged clip, or a part that won't stay seated

• Disconnect power (and gas/water if applicable) before servicing; wear cut-resistant gloves and eye protection
• Support the component while releasing/installing the clip; needle-nose pliers or a flat tool can help
• Note clip orientation and reinstall in the same position; do not over-bend—replace if the clip has lost tension or is corroded

Used from harness to top.

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

Replacement plug button that snaps into place to cover a small access hole or fastener opening. Restores a finished appearance and helps keep dirt, moisture and small objects out of the appliance cavity. What it does:

• Covers exposed holes or mounting openings for a clean, finished look
• Prevents dirt and debris from entering small internal cavities
• Replaces missing, cracked or worn plug buttons that no longer stay seated
• Small, low-profile design to match factory appearance

• Disconnect power to the appliance before servicing
• Typically installs by pressing into the opening until it snaps flush; a small flat screwdriver can assist
• Avoid prying against surrounding trim to prevent cosmetic damage
• Keep small parts away from children and pets

Right hand side

This welded base assembly forms the lower chassis of the unit, supporting the cabinet and mounted components. Replacing a bent, rusted, or damaged base restores structural integrity, alignment, and smoother, quieter operation.

• Serves as the main lower support structure for the cabinet/frame
• Provides mounting points for brackets, fasteners, and levelers as designed
• Helps maintain alignment of panels/doors and overall stability
• Common signs of failure: bent or rusted-through metal, excessive vibration or rattling, difficulty leveling, misaligned panels or drawer

• Disconnect power; also shut off water and/or gas before service
• Use proper lifting/support; sheet-metal edges can be sharp—wear cut-resistant gloves and eye protection
• Transfer any reusable fasteners, grommets, and brackets from the original base
• After reassembly, ensure the unit is square and level before returning to service

Size: .20 Fl. Oz. (6 ml)